SURFACE MOUNT DISPLAY Part Number: ACDC04-41SEKWA-F01 Super Bright Orange Features Description z 0.4INCH DIGIT HEIGHT. The Super Bright Orange device is made with InGaAlP z LOW CURRENT OPERATION. (on GaAs substrate) light emitting diode chip. z EXCELLENT CHARACTER APPEARANCE. z I.C. COMPATIBLE. z MECHANICALLY RUGGED. z GRAY FACE,WHITE SEGMENT. z PACKAGE: 250PCS/ REEL. z MOISTURE SENSITIVITY LEVEL : LEVEL 4. z RoHS COMPLIANT. Package Dimensions& Internal Circuit Diagram Notes: 1. All dimensions are in millimeters (inches), Tolerance is ±0.25(0.01")unless otherwise noted. 2. Specifications are subject to change without notice. 3.The gap between the reflector and PCB shall not exceed 0.25mm. SPEC NO: DSAG0250 REV NO: V.5 DATE: JUN/14/2007 PAGE: 1 OF 5 APPROVED: WYNEC CHECKED: Joe Lee DRAWN: Y.H.CHEN ERP: 1352000327 Selection Guide Part No. Dice ACDC04-41SEKWA-F01 Iv (ucd) [1] @ 10mA Lens Type Super Bright Orange (InGaAlP) WHITE DIFFUSED Description Min. Typ. 12000 41200 Common Cathode, Rt. Hand Decimal Units Test Conditions Note: 1. Luminous intensity/ luminous Flux: +/-15%. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. Max. λpeak Peak Wavelength Super Bright Orange 610 nm IF=20mA λD [1] Dominant Wavelength Super Bright Orange 601 nm IF=20mA Δλ1/2 Spectral Line Half-width Super Bright Orange 29 nm IF=20mA C Capacitance Super Bright Orange 15 pF VF=0V;f=1MHz VF [2] Forward Voltage Super Bright Orange 2.1 2.5 V IF=20mA IR Reverse Current Super Bright Orange 10 uA VR=5V Notes: 1.Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. Absolute Maximum Ratings at TA=25°C Parameter Super Bright Orange Units Power dissipation 75 mW DC Forward Current 30 mA Peak Forward Current [1] 195 mA 5 V Reverse Voltage Operating / Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAG0250 REV NO: V.5 DATE: JUN/14/2007 PAGE: 2 OF 5 APPROVED: WYNEC CHECKED: Joe Lee DRAWN: Y.H.CHEN ERP: 1352000327 Super Bright Orange ACDC04-41SEKWA-F01 SPEC NO: DSAG0250 REV NO: V.5 DATE: JUN/14/2007 PAGE: 3 OF 5 APPROVED: WYNEC CHECKED: Joe Lee DRAWN: Y.H.CHEN ERP: 1352000327 ACDC04-41SEKWA-F01 Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.15) Reel Dimension Tape Specifications (Units : mm) SPEC NO: DSAG0250 REV NO: V.5 DATE: JUN/14/2007 PAGE: 4 OF 5 APPROVED: WYNEC CHECKED: Joe Lee DRAWN: Y.H.CHEN ERP: 1352000327 PACKING & LABEL SPECIFICATIONS ACDC04-41SEKWA-F01 SPEC NO: DSAG0250 REV NO: V.5 DATE: JUN/14/2007 PAGE: 5 OF 5 APPROVED: WYNEC CHECKED: Joe Lee DRAWN: Y.H.CHEN ERP: 1352000327