SUBMINIATURE SOLID STATE LAMP Part Number: AM2520CGCK03 Green Features Description z SUBMINIA TURE PACKAGE. The Green source color devices are made with InGaAlP on z WIDE VIEWING ANGLE. GaAs substrate Light Emitting Diode. z GULL WING LEAD. z LONG LIFE - SOLID STATE RELIABILITY. z LOW PACKAGE PROFILE. z MOISTURE SENSITIVITY LEVEL : LEVEL 3. z PACKAGE : 1000PCS / REEL. z RoHS COMPLIANT. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. 4. Specifications are subject to change without notice. 5. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAC3399 REV NO: V.3 DATE: MAY/08/2007 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.L.LI PAGE: 1 OF 5 ERP: 1202000449 Selection Guide Part No. Dice AM2520CGCK03 Lens Type Green (InGaAlP) WATER CLEAR Viewing Angle [1] Iv (mcd) [2] @ 20mA Min. Typ. 2θ1/2 110 400 20° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. 2. Luminous intensity/ luminous Flux: +/-15%. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Green λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 574 nm IF=20mA Green 570 nm IF=20mA Spectral Line Half-width Green 20 nm IF=20mA C Capacitance Green 15 pF VF=0V;f=1MHz VF [2] Forward Voltage Green 2.1 2.5 V IF=20mA IR Reverse Current Green 10 uA VR=5V Notes: 1.Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. Absolute Maximum Ratings at TA=25°C Parameter Green Units Power dissipation 75 mW DC Forward Current 30 mA Peak Forward Current [1] 150 mA 5 V Reverse Voltage Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAC3399 REV NO: V.3 DATE: MAY/08/2007 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.L.LI PAGE: 2 OF 5 ERP: 1202000449 Green AM2520CGCK03 SPEC NO: DSAC3399 REV NO: V.3 DATE: MAY/08/2007 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.L.LI PAGE: 3 OF 5 ERP: 1202000449 AM2520CGCK03 Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Tape Specifications (Units : mm) SPEC NO: DSAC3399 REV NO: V.3 DATE: MAY/08/2007 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.L.LI PAGE: 4 OF 5 ERP: 1202000449 PACKING & LABEL SPECIFICATIONS AM2520CGCK03 SPEC NO: DSAC3399 REV NO: V.3 DATE: MAY/08/2007 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.L.LI PAGE: 5 OF 5 ERP: 1202000449