SUBMINIATURE SOLID STATE LAMP Part Number: AM27MGC09 Features Mega Green Description SUBMINIATURE PACKAGE. The Mega Green source color devices are made with DH WIDE VIEWING ANGLE. InGaAlP on GaAs substrate Light Emitting Diode. Z-BEND LEAD. LONG LIFE - SOLID STATE RELIABILITY. LOW PACKAGE PROFILE. PACKAGE :1000PCS / REEL. MOISTURE SENSITIVITY LEVEL : LEVEL 3. RoHS COMPLIANT. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. 4. Specifications are subject to change without notice. 5. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAD1337 REV NO: V.6 DATE: MAY/08/2007 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.L.LI PAGE: 1 OF 5 ERP: 1202000286 Selection Guide Part No. Dice AM27MGC09 Lens Type Mega Green (InGaAlP) WATER CLEAR Iv (mcd) [2] @ 20mA Viewing Angle [1] Min. Typ. 2<1/2 280 600 20° Notes: 1. ?1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. 2. Luminous intensity/ luminous Flux: +/-15%. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. Hpeak Peak Wavelength Mega Green HD [1] Dominant Wavelength LH1/2 Max. Units Test Conditions 574 nm IF=20mA Mega Green 568 nm IF=20mA Spectral Line Half-width Mega Green 26 nm IF=20mA C Capacitance Mega Green 20 pF VF=0V;f=1MHz VF [2] Forward Voltage Mega Green 2.1 2.5 V IF=20mA IR Reverse Current Mega Green 10 uA VR=5V Notes: 1.Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. Absolute Maximum Ratings at TA=25°C Parameter Mega Green Units Power dissipation 75 mW DC Forward Current 30 mA Peak Forward Current [1] 150 mA 5 V Reverse Voltage Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAD1337 REV NO: V.6 DATE: MAY/08/2007 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.L.LI PAGE: 2 OF 5 ERP: 1202000286 Mega Green AM27MGC09 SPEC NO: DSAD1337 REV NO: V.6 DATE: MAY/08/2007 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.L.LI PAGE: 3 OF 5 ERP: 1202000286 AM27MGC09 Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Tape Specifications (Units : mm) SPEC NO: DSAD1337 REV NO: V.6 DATE: MAY/08/2007 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.L.LI PAGE: 4 OF 5 ERP: 1202000286 PACKING & LABEL SPECIFICATIONS AM27MGC09 SPEC NO: DSAD1337 REV NO: V.6 DATE: MAY/08/2007 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.L.LI PAGE: 5 OF 5 ERP: 1202000286