KINGBRIGHT AM27SEC08

SUBMINIATURE SOLID STATE LAMP
AM27SEC08
SUPER BRIGHT ORANGE
Features
OSUBMINIATURE PACKAGE.
Description
OWIDE VIEWING ANGLE.
The Super Bright Orange source color devices are
OYOKE LEAD.
made with DH InGaAlP on GaAs substrate Light
OLONG LIFE-SOLID STATE RELIABILITY.
Emitting Diode.
OLOW PACKAGE PROFILE.
OPACKAGE : 1000PCS / REEL.
ORoHS COMPLIANT.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. Lead spacing is measured where the lead emerge from the package.
4. Specifications are subject to change without notice.
SPEC NO: DSAD1314
APPROVED: J. Lu
REV NO: V.2
CHECKED: Allen Liu
DATE: MAR/09/2005
DRAWN: S.H.CHEN
PAGE: 1 OF 4
ERP:1202000323
Selection Guide
Part No.
Dice
AM27SEC08
Iv (mcd)
@ 20mA
Lens Type
SUPER BRIGHT ORANGE (InGaAlP)
WATER CLEAR
Viewing
Angle
Min.
Typ.
2 θ 1/2
480
1300
20°
Note:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value.
Electrical / Optical Characteristics at TA=25°C
Symbol
Parameter
Device
λpeak
Peak Wavelength
Super Bright Orange
λD
Dominant Wavelength
∆λ1/2
Typ.
Max.
Units
Test Conditions
610
nm
IF=20mA
Super Bright Orange
601
nm
IF=20mA
Spectral Line Half-width
Super Bright Orange
29
nm
IF=20mA
C
Capacitance
Super Bright Orange
30
pF
VF=0V;f=1MHz
VF
Forward Voltage
Super Bright Orange
2.0
2.5
V
IF=20mA
IR
Reverse Current
Super Bright Orange
10
uA
VR= 5V
Absolute Maximum Ratings at TA=25°C
Parameter
Super Bright Orange
Units
Power dissipation
75
mW
DC Forward Current
30
mA
Peak Forward Current [1]
195
mA
5
V
Reverse Voltage
-40°C To +85°C
Operating/Storage Temperature
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
SPEC NO: DSAD1314
APPROVED: J. Lu
REV NO: V.2
CHECKED: Allen Liu
DATE: MAR/09/2005
DRAWN: S.H.CHEN
PAGE: 2 OF 4
ERP:1202000323
Super Bright Orange
SPEC NO: DSAD1314
APPROVED: J. Lu
AM27SEC08
REV NO: V.2
CHECKED: Allen Liu
DATE: MAR/09/2005
DRAWN: S.H.CHEN
PAGE: 3 OF 4
ERP:1202000323
AM27SEC08
Recommended Soldering Pattern
(Units : mm)
Tape Specifications
(Units : mm)
Remarks:
If there is sorting requirement (eg. forward voltage, luminous intensity or wavelength), the condition as follows:
1.Wavelength: +/-1nm (Test condition is based on the sorting standard).
2.Luminous intensity: +/-15% (Test condition is based on the sorting standard).
3.Forward voltage: +/-0.1V (Test condition is based on the sorting standard).
SPEC NO: DSAD1314
APPROVED: J. Lu
REV NO: V.2
CHECKED: Allen Liu
DATE: MAR/09/2005
DRAWN: S.H.CHEN
PAGE: 4 OF 4
ERP:1202000323