3.0mmx1.0 mm RIGHT ANGLE SMD CHIP LED LAMP APA3010SEC Features z3.0mmx1.0mm RIGHT ANGLE SMT LED, 2.0mm THICKNESS. SUPER BRIGHT ORANGE Description The Super Bright Orange device is made with DH InGaAlP (on GaAs substrate) light emitting diode chip. zLOW POWER CONSUMPTION. zWIDE VIEWING ANGLE. zIDEAL FOR BACK LIGHT AND INDICATOR. zVARIOUS COLORS AND LENS TYPES AVAILABLE. zPACKAGE : 2000PCS / REEL. zRoHS COMPLIANT. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.15(0.006") unless otherwise noted. 3. Specifications are subject to change without notice. SPEC NO: DSAD1039 REV NO: V.6 DATE: JUN/29/2005 PAGE: 1 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: .S.H.CHEN ERP: 1203000614 Selection Guide Part No. Dice APA3010SEC Iv (mcd) @ 20mA Lens Type SUPER BRIGHT ORANGE (InGaAlP) WATER CLEAR Viewing Angle Min. Typ. 2θ1/2 70 300 120° Note: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Super Bright Orange λD Dominant Wavelength ∆λ1/2 Max. Units Test Conditions 610 nm IF=20mA Super Bright Orange 601 nm IF=20mA Spectral Line Half-width Super Bright Orange 29 nm IF=20mA C Capacitance Super Bright Orange 30 pF VF=0V;f=1MHz VF Forward Voltage Super Bright Orange 2.0 2.5 V IF=20mA IR Reverse Current Super Bright Orange 10 uA VR= 5V Absolute Maximum Ratings at TA=25°C Parameter Super Bright Orange Units Power dissipation 75 mW DC Forward Current 30 mA Peak Forward Current [1] 195 mA Reverse Voltage 5 V Operating / Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAD1039 REV NO: V.6 DATE: JUN/29/2005 PAGE: 2 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: .S.H.CHEN ERP: 1203000614 Super Bright Orange APA3010SEC SPEC NO: DSAD1039 REV NO: V.6 DATE: JUN/29/2005 PAGE: 3 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: .S.H.CHEN ERP: 1203000614 APA3010SEC Recommended Soldering Pattern (Units : mm) Tape Specifications (Units : mm) SPEC NO: DSAD1039 REV NO: V.6 DATE: JUN/29/2005 PAGE: 4 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: .S.H.CHEN ERP: 1203000614 PACKING & LABEL SPECIFICATIONS APA3010SEC Remarks: If special sorting is required (e.g. binning based on forward voltage, luminous intensity, or wavelength), the typical accuracy of the sorting process is as follows: 1. Wavelength: +/-1nm 2. Luminous Intensity: +/-15% 3. Forward Voltage: +/-0.1V Note: Accuracy may depend on the sorting parameters. SPEC NO: DSAD1039 REV NO: V.6 DATE: JUN/29/2005 PAGE: 5 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: .S.H.CHEN ERP: 1203000614