T-1 3/4 (5mm) VARIABLE HEIGHT LED BOARD INDICATOR WP7113BR9.52/ID Features HIGH EFFICIENCY RED Description LED FIRMLY HELD BY SPACER-NO ADDITIONAL FIXTURING OR GLUEING NECESSARY. SUITABLE FOR BACK PANEL ILLUMINATION, The High Efficiency Red source color devices are made with Gallium Arsenide Phosphide on Gallium Phosphide Orange Light Emitting Diode. CIRCUIT BOARD INDICATOR, LED INDICATOR. UL RATING:94V-0. HOUSING MATERIAL:TYPE 66 NYLON. RoHS COMPLIANT. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. 4. Specifications are subject to change without notice. SPEC NO: DSAF2108 APPROVED: J. Lu REV NO: V.1 CHECKED: Allen Liu DATE:APR/19/2005 DRAWN: H.Q.YUAN PAGE: 1 OF 4 ERP:1102001516 Selection Guide Part No. Dice WP7113BR9.52/ID Iv (mcd) @ 10mA Lens Type HIGH EFFICIENCY RED (GaAsP/GaP) Viewing Angle Min. Typ. 2 θ 1/2 8 45 30° RED DIFFUSED Note: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength High Efficiency Red λD Dominant Wavelength ∆λ1/2 Max. Units Test Conditions 627 nm IF=20mA High Efficiency Red 625 nm IF=20mA Spectral Line Half-width High Efficiency Red 45 nm IF=20mA C Capacitance High Efficiency Red 15 pF VF=0V;f=1MHz VF Forward Voltage High Efficiency Red 2.0 2.5 V IF=20mA IR Reverse Current High Efficiency Red 10 uA VR = 5V Absolute Maximum Ratings at TA=25°C Parameter High Efficiency Red Units Power dissipation 105 mW DC Forward Current 30 mA Peak Forward Current [1] 160 mA 5 V Reverse Voltage Operating/Storage Temperature -40°C To +85°C Lead Solder Temperature [2] 260°C For 3 Seconds Lead Solder Temperature [3] 260°C For 5 Seconds Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. 2mm below package base. 3. 5mm below package base. SPEC NO: DSAF2108 APPROVED: J. Lu REV NO: V.1 CHECKED: Allen Liu DATE:APR/19/2005 DRAWN: H.Q.YUAN PAGE: 2 OF 4 ERP:1102001516 High Efficiency Red WP7113BR9.52/ID Remarks: If special sorting is required (e.g. binning based on forward voltage,luminous intensity, or wavelength), the typical accuracy of the sorting process is as follows: 1. Wavelength: +/-1nm 2. Luminous Intensity: +/-15% 3. Forward Voltage: +/-0.1V Note: Accuracy may depend on the sorting parameters. SPEC NO: DSAF2108 APPROVED: J. Lu REV NO: V.1 CHECKED: Allen Liu DATE:APR/19/2005 DRAWN: H.Q.YUAN PAGE: 3 OF 4 ERP:1102001516 PACKING & LABEL SPECIFICATIONS SPEC NO: DSAF2108 APPROVED: J. Lu REV NO: V.1 CHECKED: Allen Liu WP7113BR9.52/ID DATE:APR/19/2005 DRAWN: H.Q.YUAN PAGE: 4 OF 4 ERP:1102001516