KINGBRIGHT WP1034IDT

2mm FLAT TOP LED LAMP
WP1034IDT
Features
HIGH EFFICIENCY RED
Description
MOUNTS FLUSH WITH PANEL.
The High Efficiency Red source color devices are made with
LOW POWER CONSUMPTION.
Gallium Arsenide Phosphide on Gallium Phosphide Orange
LONG LIFE - SOLID STATE RELIABILITY.
Light Emitting Diode.
RoHS COMPLIANT.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. Lead spacing is measured where the leads emerge from the package.
4. Specifications are subject to change without notice.
SPEC NO: DSAF2526
REV NO: V.1
DATE: APR/18/2005
PAGE: 1 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: W.J.ZHU
ERP:1101000336
Selection Guide
Part No.
Dice
WP1034IDT
Iv (mcd)
@ 10mA
Lens Type
HIGH EFFICIENCY RED (GaAsP/GaP)
RED DIFFUSED
Viewing
Angle
Min.
Typ.
2 θ 1/2
3
8
70°
Note:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value.
Electrical / Optical Characteristics at TA=25°C
Symbol
Parameter
Device
Typ.
λpeak
Peak Wavelength
High Efficiency Red
λD
Dominant Wavelength
∆λ1/2
Max.
Units
Test Conditions
627
nm
IF=20mA
High Efficiency Red
625
nm
IF=20mA
Spectral Line Half-width
High Efficiency Red
45
nm
IF=20mA
C
Capacitance
High Efficiency Red
15
pF
VF=0V;f=1MHz
VF
Forward Voltage
High Efficiency Red
2.0
2.5
V
IF=20mA
IR
Reverse Current
High Efficiency Red
10
uA
VR= 5V
Absolute Maximum Ratings at TA=25°C
Parameter
High Efficiency Red
Units
Power dissipation
105
mW
DC Forward Current
30
mA
Peak Forward Current [1]
160
mA
5
V
Reverse Voltage
Operating / Storage Temperature
-40°C To +85°C
Lead Solder Temperature [2]
260°C For 3 Seconds
Lead Solder Temperature [3]
260°C For 5 Seconds
Notes:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
2. 2mm below package base.
3. 5mm below package base.
SPEC NO: DSAF2526
REV NO: V.1
DATE: APR/18/2005
PAGE: 2 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: W.J.ZHU
ERP:1101000336
High Efficiency Red
WP1034IDT
SPEC NO: DSAF2526
REV NO: V.1
DATE: APR/18/2005
PAGE: 3 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: W.J.ZHU
ERP:1101000336
PACKING & LABEL SPECIFICATIONS
WP1034IDT
Remarks:
If special sorting is required (e.g. binning based on forward voltage, luminous intensity, or wavelength),
the typical accuracy of the sorting process is as follows:
1. Wavelength: +/-1nm
2. Luminous Intensity: +/-15%
3. Forward Voltage: +/-0.1V
Note: Accuracy may depend on the sorting parameters.
SPEC NO: DSAF2526
REV NO: V.1
DATE: APR/18/2005
PAGE: 4 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: W.J.ZHU
ERP:1101000336