KODENSHI KK33091AN

TECHNICAL DATA
Powerful High-grade FET driver
KK33091A
Description of basic functions.
The capability of handling high voltages on power line attributed to
transient commutation of loads in conditions of automobile exploitation.
Load of microcircuit is a device on the base of MOS transistors
that enables switching high current levels in automobile electrical
system. Microcircuit has Fault indication output when there is short
circuit in load or when load transistor current level exceeds preset value.
ORDERING INFORMATION
KK33091AN Plastic
KK33091AD SOIC
TA = -40° to 125° C
for all packages.
Functions
Microcircuit provides pumping of charge (on output capacity on
pin Gate of gate control)to drive power MOS transistor. Input Input , compatible with logic levels
of CMOS microcircuits ,controls pumping of charge (switch in/switch off).
Check of drain-source voltage is implemented (VDS) on power МОS transistor, detection of
shorted load , presentation of error signal on pin Fault.
Microcircuit has pin VT of timer, that is both input in timer window comparators and output of
current square circuit, depending on r m s voltage drain-source on power MOS transistor, as power
dissipated in МОS device is proportional to VDS2.
External resistor RT and capacitor CT, connected to timer pin enable programming of timing data
necessary for protection of power MOS-device.
Internal circuit of stabilizer diodes with the total break down voltage of about 30V provides
protection of microcircuit and power МОS transistor from supply voltage value to be exceeded.
Activation of microcircuit Zener stabilizer diodes attributed to switching-off МОS transistor for the
time when supply voltage value exceeded , in addition pin Fault does not change its logic state .
1
KK33091A
Features.
• Works with a wide variety of N-channel power field transistors
• Input of control compatible with CMOS logic
• Built in pumping of charge without external components
• Detection and protection from shorted load and current exceeding
• Failure unit reporting a FET overcurrent and shorted load condition
• Possibility to connect induced loads
• Forward overvoltage and battery polarity reverse protection
• Extended range of operating temperatures
Table of Maximum operation ratings and absolute maximum ratings .
Maximum operation ratings and absolute maximum ratings of exploitation
Name of parameter , unit of
measurement
Symbol
1
supply voltage on output VCC (pin
05), V
Consumption current in mode of
limiting by protection (input 05),
mА
DIP package
SO-8 package
Range of adjusting voltage on input
Input (pin 07),V
(direct voltage)
2
range of voltage, delivered to pin
»» (pin 06), V
(direct voltage)
Temperature of chip, °С
Temperature of storage, °С
operation range of ambient
temperatures, °С
VCC
IC
Maximum operation
rating
Standard
min
max
3
4
7,0
24,0
Absolute maximum
rating
Standard
min
max
5
6
-0,7
28,0
10
1,0
Vin
-0,7
28,0
-0.7
-65
-65
28,0
150
150
-65
150
VOUT
TJ
TSTG
ТA
-40
125
2
KK33091A
Тable of electrical parameters .
Electrical parameters of microcircuits KK33091AN, KK33091AD
Name of parameter,
unit of measurement
Symbol
Mode of measurement
standard
consumption current, mА
Icc
Limitation value of supply voltage on
pin Vcc (pin 05), V
output voltage range on pin »Gate» (pin
04) relatively voltage of power supply
source Vcc, V
current on pin »Gate» (pin 04), µА
output voltage of saturation on
pin»Gate» (pin 04), V
voltage on pin »Gate» in mode of load
short circuit (pin 06), V
Threshold voltage on input »Input»
(pin 07), V
input current of pin »Input» (pin 07), µ
А
current coefficient of timer (pin 08), µ
А/V2
threshold voltage of synchronization
(pin 08), V
lower level
upper level
current on pin »» (pin 06), µА
Vz
29,0
max
0,3
6,0
35,0
VGS
8,0
15,0
-
30
0
400
1,4
-
VGC
6,4
7,7
4
VIL
VIH
Iin
3,5
-
1,5
250
-
0,7
1,5
5
0,4
4,3
500
-
1,2
5,2
0,1
0,8
-
IG
VG(sat)
К
VTL
VTH
IOL
IOH
VOL
Vin = 0 V:
Vin=5,0 V (Rx=100 kОhm):
VG =Vcc
IG =10µА
Vin=5,0 V
Rx=100 kОhm, Vт=0, VDC=1,0
V
VF =5,0 V
VF =0
IF =500 µА
min
-
note
2
3
-
-
Voltage of saturation on pin»» (pin
06), V
Note
1 .Standards for electrical parameters of table , unless otherwise noted , are given for conditions :
7,0 V ≤ Vcc ≤ 24 V; -40°С ≤ Тa ≤125°С.
2 .Measure total consumption current on pins 02 and 05 of microcircuit (when resistor is Rx=100 kОhm, connected
to pin 02, and resistor with the value of 45 kОhm, connected to pin 06).
3 . Protection of device from short-term voltage surge on power line at the expense of internal circuit of
semiconductor stabilitrons.
4. Measure voltage relatively pin «SRC» in shorted load mode , when voltage on load approximately will make less
than 1В in НУ relatively potential «general». Mode of measurements , residual stress on load of short-circuit mode are to
be specified in the course of development basing on the reference dependence reading results for temperature range.
5 Current coefficient of timer is a constant (coefficient )of proportionality of voltage into current conversion, used to
check VDS voltage, formed on field transistor.
For microcircuit KK33091AN, arranged in 8-pin plastic DIP-package of MS-001BA type, Rtja is 100 °С/W; For
microcircuit KK33091AD – arranged in 8-pin plastic SO-package of MS-012AA MC33091AD type, Rtja is 145 °С/W.
permissible value of static potential value is 2000 V (human body model).
Nominal block diagram and IC connection circuit
3
KK33091A
Тable of pin purpose.
Table of pin purpose of microcircuits KK33091AN, KK33091AD
№ of pin
Purpose of pin
01
02
pin of voltage check on load (SRC)
pin for connection to resistor generating current dependence from voltage on
external transistor (DRN)
general pin (GND)
pin of external transistor gate control (Gate)
pin of connection to supply voltage chain (Vcc)
pin of emergency indication ()
control input (Input)
pin of timer timesetting circuit (Vт)
03
04
05
06
07
08
4
KK33091A
N SUFFIX PLASTIC DIP
(MS – 001BA)
A
Dimension, mm
5
8
B
1
4
C
-T- SEATING
PLANE
N
G
M
K
0.25 (0.010) M
J
H
D
MIN
MAX
A
8.51
10.16
B
6.1
7.11
5.33
C
L
F
Symbol
T
NOTES:
1. Dimensions “A”, “B” do not include mold flash or protrusions.
Maximum mold flash or protrusions 0.25 mm (0.010) per side.
D
0.36
0.56
F
1.14
1.78
G
2.54
H
7.62
J
0°
10°
K
2.92
3.81
L
7.62
8.26
M
0.2
0.36
N
0.38
D SUFFIX SOIC
(MS - 012AA)
Dimension, mm
A
8
5
B
H
1
G
P
4
R x 45
C
-TD
K
SEATING
PLANE
J
F
0.25 (0.010) M T C M
NOTES:
1. Dimensions A and B do not include mold flash or protrusion.
2. Maximum mold flash or protrusion 0.15 mm (0.006) per side
for A; for B ‑ 0.25 mm (0.010) per side.
M
Symbol
MIN
MAX
A
4.8
5
B
3.8
4
C
1.35
1.75
D
0.33
0.51
F
0.4
1.27
G
1.27
H
5.72
J
0°
8°
K
0.1
0.25
M
0.19
0.25
P
5.8
6.2
R
0.25
0.5
5