TECHNICAL DATA KK7407 Hex Buffers/Drivers with OpenCollector High-Voltage Outputs LOGIC DIAGRAM ORDERING INFORMATION KK7407N Plastic KK7407D SOIC TA = -10° to 70° C for all packages PIN ASSIGNMENT FUNCTION TABLE PIN 14 =VCC PIN 7 = GND Inputs Output A Y H Z L H Z = High Impedance 1 KK7407 MAXIMUM RATINGS* Symbol Parameter Value Unit VCC Supply Voltage 7.0 V VIN Input Voltage 5.5 V VOUT Output Voltage 30 V Tstg Storage Temperature Range -65 to +150 °C * Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. RECOMMENDED OPERATING CONDITIONS Symbol Parameter Min Max Unit 5.25 V VCC Supply Voltage 4.75 VIH High Level Input Voltage 2.0 VIL Low Level Input Voltage 0.8 V UOH High Level Output Voltage 30 V IOL Low Level Output Current 40 mA TA Ambient Temperature Range +70 °C -10 V DC ELECTRICAL CHARACTERISTICS over full operating conditions Guaranteed Limit Symbol Parameter Test Conditions Min Max Unit VIK Input Clamp Voltage VCC = min, IIN = -12 mA -1.5 V IOH High Level Output Current VCC = min, VOH =max 0.25 mA VOL Low Level Output Voltage VCC = min, IOL = 16 mA 0.4 V VCC = min, IOL = 40 mA 0.7 VCC = max, VIN = 2.4 V 0.04 µA VCC = max, VIN =5.5 V 1.0 mA IIH High Level Input Current IIL Low Level Input Current VCC = max, VIN = 0.4 V -1.6 mA ICC Supply Current VCC = max Outputs High 41 mA Outputs Low 30 2 KK7407 AC ELECTRICAL CHARACTERISTICS (T = 25°C, VCC = 5.0 V, CL = 15 pF, RL = 110 Ω, Input tr = tf = 10 ns) Symbol Parameter tPLH tPHL Min Max Unit Propagation Delay Time, Low to High Level Output (from Input to Output) 10 ns Propagation Delay Time, High to Low Level Output (from Input to Output) 35 ns Figure 1. Switching Waveforms * Includes all probe and jig capacitance Figure 2. Test Circuit 3 KK7407 N SUFFIX PLASTIC DIP (MS - 001AA) A Dimension, mm 8 14 B 7 1 Symbol MIN MAX A 18.67 19.69 B 6.1 7.11 5.33 C F L C -T- SEATING PLANE N G M K J H D 0.25 (0.010) M T NOTES: 1. Dimensions “A”, “B” do not include mold flash or protrusions. Maximum mold flash or protrusions 0.25 mm (0.010) per side. D 0.36 0.56 F 1.14 1.78 G 2.54 H 7.62 J 0° 10° K 2.92 3.81 L 7.62 8.26 M 0.2 0.36 N 0.38 D SUFFIX SOIC (MS - 012AB) Dimension, mm A 14 8 H B 1 G P 7 R x 45 C -TK D SEATING PLANE J 0.25 (0.010) M T C M NOTES: 1. Dimensions A and B do not include mold flash or protrusion. 2. Maximum mold flash or protrusion 0.15 mm (0.006) per side for A; for B ‑ 0.25 mm (0.010) per side. F M Symbol MIN MAX A 8.55 8.75 B 3.8 4 C 1.35 1.75 D 0.33 0.51 F 0.4 1.27 G 1.27 H 5.27 J 0° 8° K 0.1 0.25 M 0.19 0.25 P 5.8 6.2 R 0.25 0.5 4