MITSUMI 2nd RF Units for BS Digital Broadcasting Receiver TSU37 Series DBS 2nd RF Units, CATV Converters OUTLINE This is an ultra-small second RF unit for BS digital broadcast/reception, incorporating a demodulation IC and capable of receiving BS digital, 110 degree CS and conventional CS. Because it is ultra-small with a single power supply, it can be used for a variety of purposes, such as thin receivers. FEATURES 1. Excellent BER characteristics even for 110 degree CS reception. (8PSK, 950 - 2150MHz) 2. Ultra-small size achieved through adoption of direct conversion IC in the RF section. (20cc) 3. Contains ISDB high-function and high-performance demodulation IC that supports ISDB-S. 4. High sensitivity (-80dBm, typ.) with good interference characteristics. 5. Excellent phase noise characteristics and high C/N margin. 6. Supports virtical/horizontal configuration. (Ideal for slim TVs, PC expansion slots, etc.) 7. Supply voltage driven by 3.3V single power supply. SPECIFICATIONS Item Input Frequency Range Input Level Range Input Impedance Return Loss Symbol Rate Range Modulation Type Demodulator Standard FEC Rates Output Data Controller Bus Interface Power Supply Voltage Dimension (Mounting area) *Note Specifications subject to change without notice. Specifications 950~2150MHz -65~-25dBm 75Ω -7dB max. 28.86Mbaud TC8PSK, QPSK, BPSK Based on ISDB-S BPSK, QPSK (1/2, 2/3, 3/4, 5/6, 7/8), TC8PSK (2/3) 8bit parallel TS/serial TS I2C bus controll 3.3V 56.7 (W) 28.1 (D) 12.4 (H)mm MITSUMI 2nd RF Units for BS Digital Broadcasting Receiver BLOCK DIAGRAM /RESET AGC TSERR SYNC 16MHz Switched Filter RF Input TS0-TS7 Clock BPF BPF TSCLK 1/4 (4MHz) TSEN UPD61522 Demodulation IC PORTO (Band SW) I Q SFSYNC /CN_F 3.3V +B1 (LNB) internal Control bus SDA2, SCL2 1.5V 1.5V 3.3V +B2 3.3V GND TMCC_F EMG_F I&Q LPF REG PSYNC SDA SCL DIMENSIONS 8 3/8-32UNEF 70.8 3.6 13.2 57 11 ø12 27.7 24.7 2-2 12.4 24.7 B 2-2 18.15 A 4.7 3 4.7 3 0.2 3.6 7 B Terminals 1. RF IN 2. +B1 (LNBIN) 3. GND 4. +B2 (3.3V) 5. SFSYNC/CN_F 6. TMCC_F 7. EMG-F 8. TSERR 9. TSEN 10. SCL 11. SDA 12. SYNC 13. TS0 14. TS1 15. TS2 16. TS3 17. TS4 18. TS5 19. TS6 (SDEN) 20. TS7 (SDOA) 21. TSCLK 22. PSYNC 23. /RESET 0.6 0.6 53.8 19.2 21.2 23.2 25.2 27.2 29.2 31.2 33.2 35.2 37.2 39.2 41.2 43.2 45.2 47.2 49.2 5.2 7.2 9.2 11.2 13.2 15.2 2.3 15.4 22- 0.5 Unit : mm General Tolerance : ±0.5mm