No. STSE-CC5006B <Cat.No.050303> SPECIFICATIONS FOR NICHIA CHIP TYPE BLUISH-GREEN LED MODEL : NESE021T NICHIA CORPORATION -0- Nichia STSE-CC5006B <Cat.No.050303> 1.SPECIFICATIONS (1) Absolute Maximum Ratings Item Forward Current Pulse Forward Current Allowable Reverse Current Power Dissipation Operating Temperature Storage Temperature Soldering Temperature Symbol IF IFP IR PD Topr Tstg Tsld (Ta=25°C) Unit mA mA mA mW °C °C for 10sec. for 3sec. Absolute Maximum Rating 15 50 85 60 -40 ~ +100 -40 ~ +100 Reflow Soldering : 260°C Hand Soldering : 350°C IFP Conditions : Pulse Width < = 10msec. and Duty < = 1/10 (2) Initial Electrical/Optical Characteristics Item Symbol Forward Voltage VF Luminous Intensity Iv x Chromaticity Coordinate y - Condition IF=10[mA] IF=10[mA] IF=10[mA] IF=10[mA] Typ. (3.5) (640) 0.10 0.57 (Ta=25°C) Max. Unit 4.0 V mcd - Min. 780 560 390 280 (Ta=25°C) Max. Unit 1120 mcd 780 mcd 560 mcd 390 mcd Please refer to CIE 1931 chromaticity diagram. (3) Ranking Item Luminous Intensity Rank U Rank T Rank S Rank R Symbol Iv Iv Iv Iv Condition IF=10[mA] IF=10[mA] IF=10[mA] IF=10[mA] Luminous Intensity Measurement allowance is ± 10%. Color Ranks x y Rank D 0.05 0.05 0.13 0.13 0.48 0.58 0.58 0.48 x y Rank E 0.06 0.06 0.14 0.14 0.55 0.65 0.65 0.55 x y (IF=10mA,Ta=25°C) Rank F 0.09 0.09 0.17 0.17 0.60 0.70 0.70 0.60 Color Coordinates Measurement allowance is ± 0.012. One delivery will include up to two consecutive color ranks and three luminous intensity ranks of the products. The quantity-ratio of the ranks is decided by Nichia. Correspondence table of Color Coordinates - Luminous Intensity ranks Ranking by Luminous Intensity Ranking by Color Coordinates R D E F Shaded ranks are available. -1- S T U Nichia STSE-CC5006B <Cat.No.050303> 2.TYPICAL INITIAL OPTICAL/ELECTRICAL CHARACTERISTICS Please refer to figure’s page. 3.OUTLINE DIMENSIONS AND MATERIALS Please refer to figure’s page. Material as follows ; Package : Encapsulating Resin : Electrodes : Heat-Resistant Polymer Epoxy Resin (with Diffused) Ag Plating Copper Alloy 4.PACKAGING · The LEDs are packed in cardboard boxes after taping. Please refer to figure’s page. The label on the minimum packing unit shows ; Part Number, Lot Number, Ranking, Quantity · In order to protect the LEDs from mechanical shock, we pack them in cardboard boxes for transportation. · The LEDs may be damaged if the boxes are dropped or receive a strong impact against them, so precautions must be taken to prevent any damage. · The boxes are not water resistant and therefore must be kept away from water and moisture. · When the LEDs are transported, we recommend that you use the same packing method as Nichia. 5.LOT NUMBER The first six digits number shows lot number. The lot number is composed of the following characters; -U - Year ( 4 for 2004, 5 for 2005 ) - Month ( 1 for Jan., 9 for Sep., A for Oct., - Nichia's Product Number U - Ranking by Color Coordinates - Ranking by Luminous Intensity -2- B for Nov. ) Nichia STSE-CC5006B <Cat.No.050303> 6.RELIABILITY (1) TEST ITEMS AND RESULTS Test Item Resistance to Soldering Heat (Reflow Soldering) Solderability (Reflow Soldering) Thermal Shock Standard Test Method JEITA ED-4701 300 301 Number of Damaged 0/22 Test Conditions Tsld=260°C, 10sec. (Pre treatment 30°C,70%,168hrs.) Note 2 times Tsld=215 ± 5°C, 3sec. (using flux, Lead Solder) -40°C ~ 100°C 1min. (10sec.) 1min. (Pre treatment 30°C,70%,168hrs.) -40°C ~ 25°C ~ 100°C ~ 25°C 30min. 5min. 30min. 5min. 25°C ~ 65°C ~ -10°C 90%RH 24hrs./1cycle Ta=100°C 1 time over 95% 100 cycles 0/100 100 cycles 0/100 10 cycles 0/100 1000 hrs. 0/100 Ta=60°C, RH=90% 1000 hrs. 0/100 Ta=-40°C 1000 hrs. 0/100 Steady State Operating Life Ta=25°C, IF=15mA 1000 hrs. 0/100 Steady State Operating Life of High Temperature Steady State Operating Life of High Humidity Heat Steady State Operating Life of Low Temperature Permanence of Marking Ta=85°C, IF=15mA 1000 hrs. 0/100 60°C, RH=90%, IF=15mA 1000 hrs. 0/100 Ta=-40°C, IF=10mA 1000 hrs. 0/100 1 time 0/22 4 times 0/10 3 times 3 times 0/10 0/22 Temperature Cycle Moisture Resistance Cyclic High Temperature Storage Temperature Humidity Storage Low Temperature Storage Vibration Drop Electrostatic Discharge JEITA ED-4701 300 303 JEITA ED-4701 300 307 JEITA ED-4701 100 105 JEITA ED-4701 200 203 JEITA ED-4701 200 201 JEITA ED-4701 100 103 JEITA ED-4701 200 202 JEITA ED-4701 500 501 JEITA ED-4701 400 403 JEITA ED-4701 300 304 Solvent : Isopropyl Alcohol Solvent Temperature : 20 ~ 25°C Dipping Time : 5 min. 200m/s2, 100 ~ 2000Hz (Sweep 4min.) 48min., 3directions 75cm R=1.5kΩ, C=100pF Test Voltage=2kV Negative/Positive (2) CRITERIA FOR JUDGING THE DAMAGE Criteria for Judgement Item Symbol Test Conditions Min. Max. Forward Voltage VF IF=10mA U.S.L.*) 1.1 Luminous Intensity IV IF=10mA L.S.L.**) 0.7 Condition 1 Luminous Intensity IV IF=10mA L.S.L.**) 0.5 Condition 2 *) U.S.L. : Upper Standard Level **) L.S.L. : Lower Standard Level These test items are judged by the criteria of Luminous Intensity Condition 2. -3- 0/22 Nichia STSE-CC5006B-1 <Cat.No.061115> 7.CAUTIONS (1) Moisture Proof Package · When moisture is absorbed into the SMT package it may vaporize and expand during soldering. There is a possibility that this can cause exfoliation of the contacts and damage to the optical characteristics of the LEDs. For this reason, the moisture proof package is used to keep moisture to a minimum in the package. · The moisture proof package is made of an aluminum moisture proof bag. A package of a moisture absorbent material (silica gel) is inserted into the aluminum moisture proof bag. The silica gel changes its color from blue to pink as it absorbs moisture. (2) Storage · Storage Conditions Before opening the package : The LEDs should be kept at 30°C or less and 90%RH or less. The LEDs should be used within a year. When storing the LEDs, moisture proof packaging with absorbent material (silica gel) is recommended. After opening the package : The LEDs should be kept at 30°C or less and 70%RH or less. The LEDs should be soldered within 168 hours (7days) after opening the package. If unused LEDs remain, they should be stored in moisture proof packages, such as sealed containers with packages of moisture absorbent material (silica gel). It is also recommended to return the LEDs to the original moisture proof bag and to reseal the moisture proof bag again. · If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : more than 24 hours at 65 ± 5°C · Nichia LED electrode sections are comprised of a silver plated copper alloy. The silver surface may be affected by environments which contain corrosive gases and so on. Please avoid conditions which may cause the LED to corrode, tarnish or discolor. This corrosion or discoloration may cause difficulty during soldering operations. It is recommended that the User use the LEDs as soon as possible. · Please avoid rapid transitions in ambient temperature, especially in high humidity environments where condensation can occur. (3) Heat Generation · Thermal design of the end product is of paramount importance. Please consider the heat generation of the LED when making the system design. The coefficient of temperature increase per input electric power is affected by the thermal resistance of the circuit board and density of LED placement on the board, as well as other components. It is necessary to avoid intense heat generation and operate within the maximum ratings given in this specification. · The operating current should be decided after considering the ambient maximum temperature of LEDs. -4- Nichia STSE-CC5006B-1 <Cat.No.061115> (4) Soldering Conditions · The LEDs can be soldered in place using the reflow soldering method. Nichia cannot make a guarantee on the LEDs after they have been assembled using the dip soldering method. · Recommended soldering conditions Reflow Soldering Lead Solder Lead-free Solder 180 ~ 200°C 120 ~ 150°C 120 sec. Max. 120 sec. Max. 240°C Max. 260°C Max. Pre-heat Pre-heat time Peak temperature Soldering time Condition Hand Soldering Temperature Soldering time 350°C Max. 3 sec. Max. (one time only) 10 sec. Max. 10 sec. Max. refer to refer to Temperature - profile 1. Temperature - profile 2. (N2 reflow is recommended.) Although the recommended soldering conditions are specified in the above table, reflow or hand soldering at the lowest possible temperature is desirable for the LEDs. A rapid-rate process is not recommended for cooling the LEDs down from the peak temperature. [Temperature-profile (Surface of circuit board)] Use the conditions shown to the under figure. <1 : Lead Solder> <2 : Lead-free Solder> 1~ 5°C / sec. 2.5 ~ 5°C / sec. Pre-heating 120 ~ 150°C 60sec.Max. Above 200°C 2.5 ~ 5°C / sec. 240°C Max. 10sec. Max. 1~ 5°C / sec. Pre-heating 180 ~ 200°C 60sec.Max. Above 220°C 260°C Max. 10sec. Max. 120sec.Max. 120sec.Max. [Recommended soldering pad design] Use the following conditions shown in the figure. 7 3.3 1.1 FR4 t = 1.6mm 3.5 Copper foil 7.5 3.5 1.5 4.5 1.5 PC-Board 3.3 1.1 t = 35µm (Unit : mm) : Solder resist · Occasionally there is a brightness decrease caused by the influence of heat or ambient atmosphere during air reflow. It is recommended that the User use the nitrogen reflow method. · Repairing should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used. It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. · Reflow soldering should not be done more than two times. · When soldering, do not put stress on the LEDs during heating. · After soldering, do not warp the circuit board. -5- Nichia STSE-CC5006B-1 <Cat.No.061115> (5) Cleaning · It is recommended that isopropyl alcohol be used as a solvent for cleaning the LEDs. When using other solvents, it should be confirmed beforehand whether the solvents will dissolve the package and the resin or not. Freon solvents should not be used to clean the LEDs because of worldwide regulations. · Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of ultrasonic cleaning on the LEDs depends on factors such as ultrasonic power and the assembled condition. Before cleaning, a pre-test should be done to confirm whether any damage to the LEDs will occur. (6) Static Electricity · Static electricity or surge voltage damages the LEDs. It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs. · All devices, equipment and machinery must be properly grounded. It is recommended that measures be taken against surge voltage to the equipment that mounts the LEDs. · When inspecting the final products in which LEDs were assembled, it is recommended to check whether the assembled LEDs are damaged by static electricity or not. It is easy to find static-damaged LEDs by a light-on test or a VF test at a lower current (below 1mA is recommended). · Damaged LEDs will show some unusual characteristics such as the forward voltage becomes lower, or the LEDs do not light at the low current. Criteria : (VF > 2.0V at IF=0.5mA) (7) Others · NESE021 complies with RoHS Directive. · The LED light output is strong enough to injure human eyes. Precautions must be taken to prevent looking directly at the LEDs with unaided eyes for more than a few seconds. · Flashing lights have been known to cause discomfort in people; you can prevent this by taking precautions during use. Also, people should be cautious when using equipment that has had LEDs incorporated into it. · The LEDs described in this brochure are intended to be used for ordinary electronic equipment (such as office equipment, communications equipment, measurement instruments and household appliances). Consult Nichia’s sales staff in advance for information on the applications in which exceptional quality and reliability are required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or health (such as for airplanes, aerospace, submersible repeaters, nuclear reactor control systems, automobiles, traffic control equipment, life support systems and safety devices). · User shall not reverse engineer by disassembling or analysis of the LEDs without having prior written consent from Nichia. When defective LEDs are found, the User shall inform Nichia directly before disassembling or analysis. · The formal specifications must be exchanged and signed by both parties before large volume purchase begins. · The appearance and specifications of the product may be modified for improvement without notice. -6- Nichia STSE-CC5006B <Cat.No.050303> ICI Chromaticity Diagram 0.9 520 530 0.8 540 510 550 0.7 F 560 E 0.6 570 500 D 580 y 0.5 590 0.4 600 610 0.3 620 630 490 0.2 480 0.1 470 460 0 0 0.1 0.2 0.3 0.4 0.5 x ½ Color Coordinates Measurement allowance is ± 0.012. -7- 0.6 0.7 0.8 5 2.5 2.0 1.5 1.0 0.5 0 3.0 3.5 4.0 4.5 5.0 Forward Voltage VF (V) Ta=25°C 3.0 0 10 20 30 40 50 60 Forward Current IFP (mA) -8- Ambient Temperature vs. Forward Voltage Ambient Temperature vs. Relative Luminosity 5.0 2.0 4.6 IFP=10mA 4.2 3.8 3.4 3.0 2.6 -60 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (°C) IFP=10mA 1.0 0.5 0.2 -60 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (°C) Allowable Forward Current IFP (mA) Relative Luminosity (a.u.) 10 Relative Luminosity (a.u.) Forward Current IFP (mA) 20 1 2.5 Forward Voltage VF (V) Ta=25°C 100 Ta=25°C 50 20 15 10 1 5 10 20 50 100 Duty Ratio (%) Ambient Temperature vs. Allowable Forward Current Allowable Forward Current IF (mA) 3.5 100 50 Duty Ratio vs. Allowable Forward Current Forward Current vs. Relative Luminosity Forward Voltage vs. Forward Current 25 20 15 10 5 0 0 20 40 60 80 100 Ambient Temperature Ta (°C) NICHIA CORPORATION NESE021 Title CHARACTERISTICS No. 050223536372 Nichia STSE-CC5006B <Cat.No.050303> Model Forward Current vs. Chromaticity diagram (λD) 1mA(513nm) 5mA(508nm) y 0.60 10mA(506nm) 0.55 0.50 50mA(500nm) 0.45 0 0.05 0.10 0.15 0.20 0.25 520 Ta=25°C 515 510 505 500 495 490 1 5 10 20 50 100 Forward Current IFP (mA) Ta=25°C IF=10mA 1.0 0.8 0.6 0.4 0.2 0 350 400 450 500 550 600 650 Wavelength λ (nm) Ambient Temperature vs. Dominant Wavelength Dominant Wavelengthλ D (nm) -9- Dominant Wavelength λ D (nm) x Forward Current vs. Dominant Wavelength 1.2 Directivity 515 0° 1.0 520 IFP=10mA Relative Luminosity (a.u.) Ta=25°C 0.65 Relative Emission Intensity (a.u.) 0.70 Spectrum 510 505 500 495 490 -60 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (°C) Ta=25°C IFP=10mA 10° 20° 30° 40° 50° 60° 0.5 70° 80° 0 90° 60° 30° Radiation Angle NICHIA CORPORATION 0.5 90° 1.0 NESE021 Title CHARACTERISTICS No. 050108536381 Nichia STSE-CC5006B <Cat.No.050303> Model 0° (2.4) Protection device 3 2 4 1 K 1 3.5 ± 0.3 K 2.8 (C 0.6) 1 Pin Mark 2 ± 0.3 (0.8) (0.4) -10- 0.8 ± 0.3 4 (1.9) K 3.2 A 2 (2.4) 3 0.8 ± 0.3 Internal Circuit ITEM PACKAGE ENCAPSULATING RESIN ELECTRODES MATERIALS Heat-Resistant Polymer Epoxy Resin (with Diffused) Ag Plating Copper Alloy NESE021 has a protection device built in as a protection circuit against static electricity. 2.2 Model NICHIA CORPORATION Title No. NESE021 OUTLINE DIMENSIONS 050108536391 Unit mm 15/1 Scale Allow ±0.2 Nichia STSE-CC5006B <Cat.No.050303> 0.7 (0.8) (2.75) 3.5±0.05 1 Pin Mark 4±0.1 Reel End of tape φ φ2 1 ±0.8 ±0 φ 13 2.85±0.1 No LEDs .2 Label 2.15±0.1 1+0.25 -0 φ 60+1 -0 2±0.05 11.4±1 9±0.3 φ 180+0 -3 3.65±0.1 φ 1.5+0.1 -0 Reel part 0.25±0.05 8+0.3 - 0.1 4±0.1 1.75±0.1 Taping part XXXX LED TYPE NxSx021T LOT XXXXXX-U QTY pcs LEDs mounting part No LEDs -11Pull direction Top cover tape Embossed carrier tape Reel Lead Min.40mm (No LEDs) Reel Lead Min.160mm (No LEDs is more than 40) Reel Lead Min.400mm Model Taping is based on the JIS C 0806 : Packaging of Electronic Components on Continuous Tapes. NICHIA CORPORATION Title No. NxSx021T TAPING DIMENSIONS 050108536401 Unit mm Scale Allow Nichia STSE-CC5006B <Cat.No.050303> 2,000pcs/Reel Nichia STSE-CC5006B-1 <Cat.No.061115> The reel and moisture absorbent material are put in the moisture proof foil bag and then heat sealed. Reel Label NICHIA Seal XXXX LED TYPE LOT QTY NxSx021T xxxxxx-U PCS NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN Moisture proof foil bag Moisture absorbent material The box is partitioned with the cardboard. Label NICHIA Nichia XXXX LED LED TYPE RANK QTY NxSx021T U PCS NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN Packing unit Moisture proof foil bag Cardboard box Cardboard box S Cardboard box M Cardboard box L Reel/bag 1reel Quantity/bag (pcs) 2,000 MAX. Dimensions (mm) 291¯237¯120¯8t 259¯247¯243¯5t 444¯262¯259¯8t NICHIA CORPORATION -12- Reel/box 7reel MAX. 15reel MAX. 30reel MAX. Quantity/box (pcs) 14,000 MAX. 30,000 MAX. 60,000 MAX. Model NxSx021T Title PACKING No. 050621542151