ADC081S021 Single Channel, 50 to 200 ksps, 8-Bit A/D Converter General Description Features The ADC081S021 is a low-power, single channel CMOS 8-bit analog-to-digital converter with a high-speed serial interface. Unlike the conventional practice of specifying performance at a single sample rate only, the ADC081S021 is fully specified over a sample rate range of 50 ksps to 200 ksps. The converter is based upon a successiveapproximation register architecture with an internal trackand-hold circuit. The output serial data is straight binary, and is compatible with several standards, such as SPI™, QSPI™, MICROWIRE, and many common DSP serial interfaces. n n n n n The ADC081S021 operates with a single supply that can range from +2.7V to +5.25V. Normal power consumption using a +3.6V or +5.25V supply is 1.3 mW and 7.7 mW, respectively. The power-down feature reduces the power consumption to as low as 2.6 µW using a +5.25V supply. The ADC081S021 is packaged in 6-lead LLP and SOT-23 packages. Operation over the industrial temperature range of −40˚C to +85˚C is guaranteed. Specified over a range of sample rates. 6-lead LLP and SOT-23 packages Variable power management Single power supply with 2.7V - 5.25V range SPI™/QSPI™/MICROWIRE/DSP compatible Key Specifications n n n n DNL INL SNR Power Consumption — 3.6V Supply — 5.25V Supply +0.04/-0.03 LSB (typ) +0.04/-0.03 LSB (typ) 49.6 dB (typ) 1.3 mW (typ) 7.7 mW (typ) Applications n Portable Systems n Remote Data Acquisition n Instrumentation and Control Systems Pin-Compatible Alternatives by Resolution and Speed All devices are fully pin and function compatible. Resolution Specified for Sample Rate Range of: 50 to 200 ksps 200 to 500 ksps 500 ksps to 1 Msps ADC121S021 ADC121S051 ADC121S101 10-bit ADC101S021 ADC101S051 ADC101S101 8-bit ADC081S021 ADC081S051 ADC081S101 12-bit Connection Diagram 20145405 Ordering Information Order Code Temperature Range Description Top Mark ADC081S021CISD −40˚C to +85˚C 6-Lead LLP Package X9C ADC081S021CISDX −40˚C to +85˚C 6-Lead LLP Package, Tape & Reel X9C ADC081S021CIMF −40˚C to +85˚C 6-Lead SOT-23 Package X09C ADC081S021CIMFX −40˚C to +85˚C 6-Lead SOT-23 Package, Tape & Reel X09C ADC081S021EVAL SOT-23 Evaluation Board TRI-STATE ® is a trademark of National Semiconductor Corporation QSPI™ and SPI™ are trademarks of Motorola, Inc. © 2006 National Semiconductor Corporation DS201454 www.national.com ADC081S021 Single Channel, 50 to 200 ksps, 8-Bit A/D Converter January 2006 ADC081S021 Block Diagram 20145407 Pin Descriptions and Equivalent Circuits Pin No. Symbol Description ANALOG I/O 3 VIN Analog input. This signal can range from 0V to VA. DIGITAL I/O 4 SCLK Digital clock input. This clock directly controls the conversion and readout processes. 5 SDATA Digital data output. The output samples are clocked out of this pin on falling edges of the SCLK pin. 6 CS Chip select. On the falling edge of CS, a conversion process begins. 1 VA Positive supply pin. This pin should be connected to a quiet +2.7V to +5.25V source and bypassed to GND with a 1 µF capacitor and a 0.1 µF monolithic capacitor located within 1 cm of the power pin. 2 GND The ground return for the supply and signals. PAD GND For package suffix CISD(X) only, it is recommended that the center pad should be connected to ground. POWER SUPPLY www.national.com 2 Operating Ratings (Notes 1, 2) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Operating Temperature Range VA Supply Voltage Voltage on Any Analog Pin to GND −0.3V to (VA +0.3V) Voltage on Any Digital Pin to GND −0.3V to 6.5V Package Input Current (Note 3) Power Consumption at TA = 25˚C 0V to VA Clock Frequency 1 MHz to 4 MHz Sample Rate See (Note 4) ESD Susceptibility (Note 5) Human Body Model Machine Model −0.3V to 5.25V Analog Input Pins Voltage Range ± 10 mA ± 20 mA Input Current at Any Pin (Note 3) +2.7V to +5.25V Digital Input Pins Voltage Range (regardless of supply voltage) −0.3V to 6.5V Analog Supply Voltage VA −40˚C ≤ TA ≤ +85˚C up to 200 ksps Package Thermal Resistance θJA Package 3500V 300V 6-lead LLP 94˚C / W Junction Temperature +150˚C 6-lead SOT-23 265˚C / W Storage Temperature −65˚C to +150˚C Soldering process must comply with National Semiconductor’s Reflow Temperature Profile specifications. Refer to www.national.com/packaging. (Note 6) ADC081S021 Converter Electrical Characteristics (Notes 7, 9) The following specifications apply for VA = +2.7V to 5.25V, fSCLK = 1 MHz to 4 MHz, fSAMPLE = 50 ksps to 200 ksps, CL = 15 pF, unless otherwise noted. Boldface limits apply for TA = TMIN to TMAX: all other limits TA = 25˚C. Symbol Parameter Conditions Typical Limits (Note 9) 8 Bits ± 0.03 ± 0.3 LSB (max) Units STATIC CONVERTER CHARACTERISTICS Resolution with No Missing Codes VA = +2.7V to +3.6V INL Integral Non-Linearity VA = +4.75V to +5.25V VA = +2.7V to +3.6V DNL VOFF GE Differential Non-Linearity Offset Error Gain Error VA = +4.75V to +5.25V VA = +2.7V to +3.6V ± 0.03 +0.04 −0.03 −0.01 VA = +4.75V to +5.25V +0.03 VA = +2.7V to +3.6V +0.04 VA = +4.75V to +5.25V +0.1 VA = +2.7V to +3.6V TUE +0.04 −0.03 Total Unadjusted Error VA = +4.75V to +5.25V +0.055 −0.065 +0.03 −0.06 ± 0.3 ± 0.2 ± 0.2 ± 0.2 ± 0.2 ± 0.4 ± 0.4 ± 0.3 ± 0.3 LSB (max) LSB (min) LSB (max) LSB (max) LSB (min) LSB (max) LSB (max) LSB (max) LSB (max) LSB (max) LSB (min) LSB (max) LSB (min) DYNAMIC CONVERTER CHARACTERISTICS SINAD Signal-to-Noise Plus Distortion Ratio VA = +2.7 to 5.25V fIN = 100 kHz, −0.02 dBFS 49.5 49 dBFS (min) SNR Signal-to-Noise Ratio VA = +2.7 to 5.25V fIN = 100 kHz, −0.02 dBFS 49.6 49 dBFS (min) THD Total Harmonic Distortion VA = +2.7 to 5.25V fIN = 100 kHz, −0.02 dBFS −77 −65 dBFS (max) SFDR Spurious-Free Dynamic Range VA = +2.7 to 5.25V fIN = 100 kHz, −0.02 dBFS 68 65 dBFS (min) ENOB Effective Number of Bits VA = +2.7 to 5.25V fIN = 100 kHz, −0.02 dBFS 7.9 7.8 Bits (min) 3 www.national.com ADC081S021 Absolute Maximum Ratings (Notes 1, 2) ADC081S021 ADC081S021 Converter Electrical Characteristics (Notes 7, 9) (Continued) The following specifications apply for VA = +2.7V to 5.25V, fSCLK = 1 MHz to 4 MHz, fSAMPLE = 50 ksps to 200 ksps, CL = 15 pF, unless otherwise noted. Boldface limits apply for TA = TMIN to TMAX: all other limits TA = 25˚C. Symbol Parameter Conditions Typical Limits (Note 9) Units DYNAMIC CONVERTER CHARACTERISTICS IMD FPBW Intermodulation Distortion, Second Order Terms VA = +5.25V fa = 103.5 kHz, fb = 113.5 kHz −83 dBFS Intermodulation Distortion, Third Order Terms VA = +5.25V fa = 103.5 kHz, fb = 113.5 kHz −82 dBFS VA = +5V 11 MHz VA = +3V 8 MHz -3 dB Full Power Bandwidth ANALOG INPUT CHARACTERISTICS VIN Input Range IDCL DC Leakage Current CINA Input Capacitance 0 to VA V ±1 µA (max) Track Mode 30 pF Hold Mode 4 pF DIGITAL INPUT CHARACTERISTICS VIH Input High Voltage VIL Input Low Voltage IIN Input Current CIND Digital Input Capacitance VA = +5.25V 2.4 VA = +3.6V 2.1 V (min) VA = +5V 0.8 V (max) VA = +3V V (min) 0.4 V (max) ± 0.1 ±1 µA (max) 2 4 pF (max) ISOURCE = 200 µA VA − 0.07 VA − 0.2 V (min) ISOURCE = 1 mA VA − 0.1 0.4 V (max) VIN = 0V or VA DIGITAL OUTPUT CHARACTERISTICS VOH Output High Voltage VOL Output Low Voltage IOZH, IOZL TRI-STATE ® Leakage Current COUT ISINK = 200 µA 0.03 ISINK = 1 mA 0.1 ± 0.1 TRI-STATE ® Output Capacitance 2 Output Coding V V ± 10 µA (max) 4 pF (max) Straight (Natural) Binary POWER SUPPLY CHARACTERISTICS VA Supply Voltage Supply Current, Normal Mode (Operational, CS low) IA Supply Current, Shutdown (CS high) Power Consumption, Normal Mode (Operational, CS low) PD Power Consumption, Shutdown (CS high) 2.7 V (min) 5.25 V (max) VA = +5.25V, fSAMPLE = 200 ksps 1.47 2.2 mA (max) VA = +3.6V, fSAMPLE = 200 ksps 0.36 0.9 mA (max) fSCLK = 0 MHz, VA = +5.25V fSAMPLE = 0 ksps 500 nA VA = +5.25V, fSCLK = 4 MHz, fSAMPLE = 0 ksps 60 µA VA = +5.25V 7.7 11.6 mW (max) VA = +3.6V 1.3 3.24 mW (max) fSCLK = 0 MHz, VA = +5.25V fSAMPLE = 0 ksps 2.6 µW fSCLK = 4 MHz, VA = +5.25V, fSAMPLE = 0 ksps 315 µW AC ELECTRICAL CHARACTERISTICS fSCLK Clock Frequency www.national.com (Note 8) 4 1.0 MHz (min) 4.0 MHz (max) (Continued) The following specifications apply for VA = +2.7V to 5.25V, fSCLK = 1 MHz to 4 MHz, fSAMPLE = 50 ksps to 200 ksps, CL = 15 pF, unless otherwise noted. Boldface limits apply for TA = TMIN to TMAX: all other limits TA = 25˚C. Symbol Parameter Conditions Typical Limits (Note 9) Units AC ELECTRICAL CHARACTERISTICS fS Sample Rate tCONV Conversion Time DC SCLK Duty Cycle tACQ (Note 8) fSCLK = 4 MHz 50 Track/Hold Acquisition Time Throughput Time Acquisition Time + Conversion Time 50 ksps (min) 200 ksps (max) 16 SCLK cycles 40 % (min) 60 % (max) 400 ns (max) 20 SCLK cycles 50 ns (min) tQUIET (Note 10) tAD Aperture Delay 3 ns tAJ Aperture Jitter 30 ps ADC081S021 Timing Specifications The following specifications apply for VA = +2.7V to 5.25V, GND = 0V, fSCLK = 1.0 MHz to 4.0 MHz, CL = 25 pF, fSAMPLE = 50 ksps to 200 ksps, Boldface limits apply for TA = TMIN to TMAX: all other limits TA = 25˚C. Symbol Limits Units tCS Minimum CS Pulse Width Parameter Conditions Typical 10 ns (min) tSU CS to SCLK Setup Time 10 ns (min) tEN Delay from CS Until SDATA TRI-STATE ® Disabled (Note 11) 20 ns (max) tACC Data Access Time after SCLK Falling Edge (Note 12) VA = +2.7V to +3.6V 40 ns (max) VA = +4.75V to +5.25V 20 ns (max) tCL SCLK Low Pulse Width 0.4 x tSCLK ns (min) tCH SCLK High Pulse Width 0.4 x tSCLK ns (min) tH SCLK to Data Valid Hold Time 7 ns (min) tDIS tPOWER-UP SCLK Falling Edge to SDATA High Impedance (Note 13) VA = +2.7V to +3.6V VA = +4.75V to +5.25V VA = +2.7V to +3.6V VA = +4.75V to +5.25V Power-Up Time from Full Power-Down 5 ns (min) 25 ns (max) 6 ns (min) 25 ns (max) 5 ns (min) 1 µs Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. Note 2: All voltages are measured with respect to GND = 0V, unless otherwise specified. Note 3: When the input voltage at any pin exceeds the power supply (that is, VIN < GND or VIN > VA), the current at that pin should be limited to 10 mA. The 20 mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of 10 mA to two. The Absolute Maximum Rating specification does not apply to the VA pin. The current into the VA pin is limited by the Analog Supply Voltage specification. Note 4: The absolute maximum junction temperature (TJmax) for this device is 150˚C. The maximum allowable power dissipation is dictated by TJmax, the junction-to-ambient thermal resistance (θJA), and the ambient temperature (TA), and can be calculated using the formula PDMAX = (TJmax − TA)/θJA. The values for maximum power dissipation listed above will be reached only when the device is operated in a severe fault condition (e.g. when input or output pins are driven beyond the power supply voltages, or the power supply polarity is reversed). Obviously, such conditions should always be avoided. Note 5: Human body model is 100 pF capacitor discharged through a 1.5 kΩ resistor. Machine model is 220 pF discharged through zero ohms Note 6: Reflow temperature profiles are different for lead-free and non-lead-free packages. Note 7: Tested limits are guaranteed to National’s AOQL (Average Outgoing Quality Level). Note 8: This is the frequency range over which the electrical performance is guaranteed. The device is functional over a wider range which is specified under Operating Ratings. Note 9: Data sheet min/max specification limits are guaranteed by design, test, or statistical analysis. Note 10: Minimum Quiet Time required by bus relinquish and the start of the next conversion. 5 www.national.com ADC081S021 ADC081S021 Converter Electrical Characteristics (Notes 7, 9) ADC081S021 ADC081S021 Timing Specifications (Continued) Note 11: Measured with the timing test circuit shown in Figure 1 and defined as the time taken by the output signal to cross 1.0V. Note 12: Measured with the timing test circuit shown in Figure 1 and defined as the time taken by the output signal to cross 1.0V or 2.0V. Note 13: tDIS is derived from the time taken by the outputs to change by 0.5V with the timing test circuit shown in Figure 1. The measured number is then adjusted to remove the effects of charging or discharging the output capacitance. This means that tDIS is the true bus relinquish time, independent of the bus loading. www.national.com 6 ADC081S021 Timing Diagrams 20145408 FIGURE 1. Timing Test Circuit 20145406 FIGURE 2. ADC081S021 Serial Timing Diagram 7 www.national.com ADC081S021 MISSING CODES are those output codes that will never appear at the ADC outputs. The ADC081S021 is guaranteed not to have any missing codes. Specification Definitions ACQUISITION TIME is the time required to acquire the input voltage. That is, it is time required for the hold capacitor to charge up to the input voltage. OFFSET ERROR is the deviation of the first code transition (000...000) to (000...001) from the ideal (i.e. GND + 1 LSB). SIGNAL TO NOISE RATIO (SNR) is the ratio, expressed in dB, of the rms value of the input signal to the rms value of the sum of all other spectral components below one-half the sampling frequency, not including harmonics or d.c. APERTURE DELAY is the time between the fourth falling SCLK edge of a conversion and the time when the input signal is acquired or held for conversion. APERTURE JITTER (APERTURE UNCERTAINTY) is the variation in aperture delay from sample to sample. Aperture jitter manifests itself as noise in the output. SIGNAL TO NOISE PLUS DISTORTION (S/N+D or SINAD) Is the ratio, expressed in dB, of the rms value of the input signal to the rms value of all of the other spectral components below half the clock frequency, including harmonics but excluding d.c. CONVERSION TIME is the time required, after the input voltage is acquired, for the ADC to convert the input voltage to a digital word. DIFFERENTIAL NON-LINEARITY (DNL) is the measure of the maximum deviation from the ideal step size of 1 LSB. SPURIOUS FREE DYNAMIC RANGE (SFDR) is the difference, expressed in dB, between the desired signal amplitude to the amplitude of the peak spurious spectral component, where a spurious spectral component is any signal present in the output spectrum that is not present at the input and may or may not be a harmonic. DUTY CYCLE is the ratio of the time that a repetitive digital waveform is high to the total time of one period. The specification here refers to the SCLK. EFFECTIVE NUMBER OF BITS (ENOB, or EFFECTIVE BITS) is another method of specifying Signal-to-Noise and Distortion or SINAD. ENOB is defined as (SINAD − 1.76) / 6.02 and says that the converter is equivalent to a perfect ADC of this (ENOB) number of bits. TOTAL HARMONIC DISTORTION (THD) is the ratio, expressed in dB or dBc, of the rms total of the first five harmonic components at the output to the rms level of the input signal frequency as seen at the output. THD is calculated as FULL POWER BANDWIDTH is a measure of the frequency at which the reconstructed output fundamental drops 3 dB below its low frequency value for a full scale input. GAIN ERROR is the deviation of the last code transition (111...110) to (111...111) from the ideal (VREF − 1 LSB), after adjusting for offset error. INTEGRAL NON-LINEARITY (INL) is a measure of the deviation of each individual code from a line drawn from negative full scale (1⁄2 LSB below the first code transition) through positive full scale (1⁄2 LSB above the last code transition). The deviation of any given code from this straight line is measured from the center of that code value. INTERMODULATION DISTORTION (IMD) is the creation of additional spectral components as a result of two sinusoidal frequencies being applied to the ADC input at the same time. It is defined as the ratio of the power in the second and third order intermodulation products to the sum of the power in both of the original frequencies. IMD is usually expressed in dB. www.national.com where Af1 is the RMS power of the input frequency at the output and Af2 through Af6 are the RMS power in the first 5 harmonic frequencies. THROUGHPUT TIME is the minimum time required between the start of two successive conversion. It is the acquisition time plus the conversion time. TOTAL UNADJUSTED ERROR is the worst deviation found from the ideal transfer function. As such, it is a comprehensive specification which includes full scale error, linearity error, and offset error. 8 ADC081S021 Typical Performance Characteristics TA = +25˚C, fSAMPLE = 50 ksps to 200 ksps, fSCLK = 1 MHz to 4 MHz, fIN = 100 kHz unless otherwise stated. INL fSCLK = 1 MHz DNL fSCLK = 1 MHz 20145420 20145421 INL fSCLK = 4 MHz DNL fSCLK = 4 MHz 20145460 20145461 DNL vs. Clock Frequency INL vs. Clock Frequency 20145465 20145466 9 www.national.com ADC081S021 Typical Performance Characteristics TA = +25˚C, fSAMPLE = 50 ksps to 200 ksps, fSCLK = 1 MHz to 4 MHz, fIN = 100 kHz unless otherwise stated. (Continued) Total Unadjusted Error vs. Clock Frequency VA = 3.0V or 5.0V SNR vs. Clock Frequency 20145467 20145463 SINAD vs. Clock Frequency SFDR vs. Clock Frequency 20145464 20145472 Spectral Response, VA = 5V fSCLK = 1 MHz THD vs. Clock Frequency 20145468 www.national.com 20145469 10 Spectral Response, VA = 5V fSCLK = 4 MHz Power Consumption vs. Throughput, fSCLK = 4 MHz 20145470 20145455 11 www.national.com ADC081S021 Typical Performance Characteristics TA = +25˚C, fSAMPLE = 50 ksps to 200 ksps, fSCLK = 1 MHz to 4 MHz, fIN = 100 kHz unless otherwise stated. (Continued) ADC081S021 Figure 4 shows the device in hold mode: switch SW1 connects the sampling capacitor to ground, maintaining the sampled voltage, and switch SW2 unbalances the comparator. The control logic then instructs the charge-redistribution DAC to add or subtract fixed amounts of charge from the sampling capacitor until the comparator is balanced. When the comparator is balanced, the digital word supplied to the DAC is the digital representation of the analog input voltage. The device moves from hold mode to track mode on the 13th rising edge of SCLK. Applications Information 1.0 ADC081S021 OPERATION The ADC081S021 is a successive-approximation analog-todigital converter designed around a charge-redistribution digital-to-analog converter core. Simplified schematics of the ADC081S021 in both track and hold modes are shown in Figure 3 and Figure 4, respectively. In Figure 3, the device is in track mode: switch SW1 connects the sampling capacitor to the input, and SW2 balances the comparator inputs. The device is in this state until CS is brought low, at which point the device moves to hold mode. 20145409 FIGURE 3. ADC081S021 in Track Mode 20145410 FIGURE 4. ADC081S021 in Hold Mode mode on the 13th rising edge of SCLK (see Figure 2). The SDATA pin will be placed back into TRI-STATE after the 16th falling edge of SCLK, or at the rising edge of CS, whichever occurs first. After a conversion is completed, the quiet time (tQUIET) must be satisfied before bringing CS low again to begin another conversion. Sixteen SCLK cycles are required to read a complete sample from the ADC081S021. The sample bits (including leading or trailing zeroes) are clocked out on falling edges of SCLK, and are intended to be clocked in by a receiver on subsequent rising edges of SCLK. The ADC081S021 will produce three leading zero bits on SDATA, followed by eight data bits, most significant first. After the data bits, the ADC081S021 will clock out four trailing zeros. If CS goes low before the rising edge of SCLK, an additional (fourth) zero bit may be captured by the next falling edge of SCLK. 2.0 USING THE ADC081S021 The serial interface timing diagram for the ADC081S021 is shown in Figure 2. CS is chip select, which initiates conversions on the ADC081S021 and frames the serial data transfers. SCLK (serial clock) controls both the conversion process and the timing of serial data. SDATA is the serial data out pin, where a conversion result is found as a serial data stream. Basic operation of the ADC081S021 begins with CS going low, which initiates a conversion process and data transfer. Subsequent rising and falling edges of SCLK will be labelled with reference to the falling edge of CS; for example, "the third falling edge of SCLK" shall refer to the third falling edge of SCLK after CS goes low. At the fall of CS, the SDATA pin comes out of TRI-STATE and the converter moves from track mode to hold mode. The input signal is sampled and held for conversion on the falling edge of CS. The converter moves from hold mode to track www.national.com 12 5.0 ANALOG INPUTS (Continued) An equivalent circuit for the ADC081S021’s input is shown in Figure 7. Diodes D1 and D2 provide ESD protection for the analog inputs. At no time should the analog input go beyond (VA + 300 mV) or (GND − 300 mV), as these ESD diodes will begin to conduct, which could result in erratic operation. 3.0 ADC081S021 TRANSFER FUNCTION The output format of the ADC081S021 is straight binary. Code transitions occur midway between successive integer LSB values. The LSB width for the ADC081S021 is VA/256. The ideal transfer characteristic is shown in Figure 5. The transition from an output code of 0000 0000 to a code of 0000 0001 is at 1/2 LSB, or a voltage of VA/512. Other code transitions occur at steps of one LSB. The capacitor C1 in Figure 7 has a typical value of 4 pF, and is mainly the package pin capacitance. Resistor R1 is the on resistance of the track / hold switch, and is typically 500 ohms. Capacitor C2 is the ADC081S021 sampling capacitor and is typically 26 pF. The ADC081S021 will deliver best performance when driven by a low-impedance source to eliminate distortion caused by the charging of the sampling capacitance. This is especially important when using the ADC081S021 to sample AC signals. Also important when sampling dynamic signals is an anti-aliasing filter. 20145414 20145411 FIGURE 7. Equivalent Input Circuit FIGURE 5. Ideal Transfer Characteristic 6.0 DIGITAL INPUTS AND OUTPUTS 4.0 TYPICAL APPLICATION CIRCUIT A typical application of the ADC081S021 is shown in Figure 6. Power is provided in this example by the National Semiconductor LP2950 low-dropout voltage regulator, available in a variety of fixed and adjustable output voltages. The power supply pin is bypassed with a capacitor network located close to the ADC081S021. Because the reference for the ADC081S021 is the supply voltage, any noise on the supply will degrade device noise performance. To keep noise off the supply, use a dedicated linear regulator for this device, or provide sufficient decoupling from other circuitry to keep noise off the ADC081S021 supply pin. Because of the ADC081S021’s low power requirements, it is also possible to use a precision reference as a power supply to maximize performance. The three-wire interface is shown connected to a microprocessor or DSP. The ADC081S021 digital inputs (SCLK and CS) are not limited by the same maximum ratings as the analog inputs. The digital input pins are instead limited to +5.25V with respect to GND, regardless of VA, the supply voltage. This allows the ADC081S021 to be interfaced with a wide range of logic levels, independent of the supply voltage. 7.0 MODES OF OPERATION The ADC081S021 has two possible modes of operation: normal mode, and shutdown mode. The ADC081S021 enters normal mode (and a conversion process is begun) when CS is pulled low. The device will enter shutdown mode if CS is pulled high before the tenth falling edge of SCLK after CS is pulled low, or will stay in normal mode if CS remains low. Once in shutdown mode, the device will stay there until CS is brought low again. By varying the ratio of time spent in the normal and shutdown modes, a system may trade-off throughput for power consumption, with a sample rate as low as zero. 7.1 Normal Mode The fastest possible throughput is obtained by leaving the ADC081S021 in normal mode at all times, so there are no power-up delays. To keep the device in normal mode continuously, CS must be kept low until after the 10th falling edge of SCLK after the start of a conversion (remember that a conversion is initiated by bringing CS low). If CS is brought high after the 10th falling edge, but before the 16th falling edge, the device will remain in normal mode, but the current conversion will be aborted, and SDATA will return to TRI-STATE (truncating the output word). Sixteen SCLK cycles are required to read all of a conversion word from the device. After sixteen SCLK cycles have 20145413 FIGURE 6. Typical Application Circuit 13 www.national.com ADC081S021 Applications Information ADC081S021 Applications Information To enter shutdown mode, a conversion must be interrupted by bringing CS high anytime between the second and tenth falling edges of SCLK, as shown in Figure 8. Once CS has been brought high in this manner, the device will enter shutdown mode, the current conversion will be aborted and SDATA will enter TRI-STATE. If CS is brought high before the second falling edge of SCLK, the device will not change mode; this is to avoid accidentally changing mode as a result of noise on the CS line. (Continued) elapsed, CS may be idled either high or low until the next conversion. If CS is idled low, it must be brought high again before the start of the next conversion, which begins when CS is again brought low. After sixteen SCLK cycles, SDATA returns to TRI-STATE. Another conversion may be started, after tQUIET has elapsed, by bringing CS low again. 7.2 Shutdown Mode Shutdown mode is appropriate for applications that either do not sample continuously, or it is acceptable to trade throughput for power consumption. When the ADC081S021 is in shutdown mode, all of the analog circuitry is turned off. 20145416 FIGURE 8. Entering Shutdown Mode 20145417 FIGURE 9. Entering Normal Mode When the VA supply is first applied, the ADC081S021 may power up in either of the two modes: normal or shutdown. As such, one dummy conversion should be performed after start-up, as described in the previous paragraph. The part may then be placed into either normal mode or the shutdown mode, as described in Sections 7.1 and 7.2. When the ADC081S021 is operated continuously in normal mode, the maximum throughput is fSCLK / 20. Throughput may be traded for power consumption by running fSCLK at its maximum specified rate and performing fewer conversions per unit time, raising the ADC081S021 CS line after the 10th and before the 15th fall of SCLK of each conversion. A plot of typical power consumption versus throughput is shown in the Typical Performance Curves section. To calculate the power consumption for a given throughput, multiply the fraction of time spent in the normal mode by the normal mode power consumption and add the fraction of time spent in shutdown mode multiplied by the shutdown mode power consumption. Note that the curve of power consumption vs. throughput is essentially linear. This is because the power consumption in the shutdown mode is so small that it can be ignored for all practical purposes. To exit shutdown mode, bring CS back low. Upon bringing CS low, the ADC081S021 will begin powering up (power-up time is specified in the Timing Specifications table). This microsecond of power-up delay results in the first conversion result being unusable. The second conversion performed after power-up, however, is valid, as shown in Figure 9. If CS is brought back high before the 10th falling edge of SCLK, the device will return to shutdown mode. This is done to avoid accidentally entering normal mode as a result of noise on the CS line. To exit shutdown mode and remain in normal mode, CS must be kept low until after the 10th falling edge of SCLK. The ADC081S021 will be fully powered-up after 16 SCLK cycles. 8.0 POWER MANAGEMENT The ADC081S021 takes time to power-up, either after first applying VA, or after returning to normal mode from shutdown mode. This corresponds to one "dummy" conversion for any SCLK frequency within the specifications in this document. After this first dummy conversion, the ADC081S021 will perform conversions properly. Note that the tQUIET time must still be included between the first dummy conversion and the second valid conversion. www.national.com 14 noise in the substrate that will degrade noise performance if that current is large enough. The larger the output capacitance, the more current flows through the die substrate and the greater is the noise coupled into the analog channel, degrading noise performance. To keep noise out of the power supply, keep the output load capacitance as small as practical. It is good practice to use a 100 Ω series resistor at the ADC output, located as close to the ADC output pin as practical. This will limit the charge and discharge current of the output capacitance and maintain noise performance. (Continued) 9.0 POWER SUPPLY NOISE CONSIDERATIONS The charging of any output load capacitance requires current from the power supply, VA. The current pulses required from the supply to charge the output capacitance will cause voltage variations on the supply. If these variations are large enough, they could degrade SNR and SINAD performance of the ADC. Furthermore, discharging the output capacitance when the digital output goes from a logic high to a logic low will dump current into the die substrate, which is resistive. Load discharge currents will cause "ground bounce" 15 www.national.com ADC081S021 Applications Information ADC081S021 Physical Dimensions inches (millimeters) unless otherwise noted 6-Lead LLP Order Number ADC081S021CISD or ADC081S021CISDX NS Package Number SDB06A 6-Lead SOT-23 Order Number ADC081S021CIMF, ADC081S021CIMFX NS Package Number MF06A www.national.com 16 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2. Leadfree products are RoHS compliant. National Semiconductor Americas Customer Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: [email protected] National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: [email protected] Tel: 81-3-5639-7560 ADC081S021 Single Channel, 50 to 200 ksps, 8-Bit A/D Converter Notes