LP3990 150mA Linear Voltage Regulator for Digital Applications General Description Key Specifications The LP3990 regulator is designed to meet the requirements of portable, battery-powered systems providing an accurate output voltage, low noise, and low quiescent current. The LP3990 will provide a 0.8V output from the low input voltage of 2V at up to 150mA load current. When switched into shutdown mode via a logic signal at the enable pin, the power consumption is reduced to virtually zero. n n n n n n n n n The LP3990 is designed to be stable with space saving ceramic capacitors as small as 0.47µF. Performance is specified for a -40˚C to 125˚C junction temperature range. For output voltages other than 0.8V, 1.35V, 1.5V, 1.8V, 2.5V, 2.8V, or 3.3V please contact your local NSC sales office. 2.0 to 6.0V 0.8 to 3.3V 150mA 0.47uF < 10nA 43uA 150uVRMS 55dB at 1kHz 105us Package All available in Lead Free option. 4 Pin micro SMD Features n n n n n Input Voltage Range Output Voltage Range Output Current Output Stable - Capacitors Virtually Zero IQ (Disabled) Very Low IQ (Enabled) Low Output Noise PSRR Fast Start Up 1% Voltage Accuracy at Room Temperature Stable with Ceramic Capacitor Logic Controlled Enable No Noise Bypass Capacitor Required Thermal-Overload and Short-Circuit Protection 1 mm x 1.28mm 6 pin LLP (SOT23 footprint) SOT23 - 5 For other package options contact your NSC sales office. Applications n Cellular Handsets n Hand-Held Information Appliances Typical Application Circuit 20076801 © 2004 National Semiconductor Corporation DS200768 www.national.com LP3990 150mA Linear Voltage Regulator for Digital Applications November 2004 LP3990 Pin Descriptions Packages Pin No Symbol Name and Function LLP micro SMD SOT23-5 5 A2 3 VEN Enable Input; Enables the Regulator when ≥ 0.95V. Disables the Regulator when ≤ 0.4V. Enable Input has 1MΩ pulldown resistor to GND. 2 A1 2 GND Common Ground. Connect to Pad. 1 B1 5 VOUT Voltage output. A 0.47µF Low ESR Capacitor should be connected to this Pin. Connect this output to the load circuit. 6 B2 1 VIN Voltage Supply Input. A 1.0µF capacitor should be connected at this input. 4 3 N/C No Connection. Do not connect to any other pin. 4 N/C No Connection. Do not connect to any other pin. Pad GND Common Ground. Connect to Pin 2. Connection Diagrams Micro SMD, 4 Bump Package 20076803 See NS package number TLA04 LLP-6 Package 20076806 See NS package number SDE06A www.national.com 2 LP3990 Connection Diagrams (Continued) SOT23 - 5 Package (MF) 20076808 See NS package number MF05A 3 www.national.com LP3990 Ordering Information For micro SMD Package * Please contact Sales Office for Availability Output Voltage (V) Grade LP3990 Supplied as 250 Units, Tape and Reel LP3990 Supplied as 3000 Units, Tape and Reel 0.8 STD LP3990TL-0.8 LP3990TLX-0.8 1.2* STD LP3990TL-1.2 LP3990TLX-1.2 1.35 STD LP3990TL-1.35 LP3990TLX-1.35 1.5 STD LP3990TL-1.5 LP3990TLX-1.5 1.8 STD LP3990TL-1.8 LP3990TLX-1.8 2.5* STD LP3990TL-2.5 LP3990TLX-2.5 2.8 STD LP3990TL-2.8 LP3990TLX-2.8 3.3* STD LP3990TL-3.3 LP3990TLX-3.3 Package Marking For LLP-6 Package * Please contact Sales Office for Availability Output Voltage (V) Grade LP3990 Supplied as 1000 Units, Tape and Reel LP3990 Supplied as 3000 Units, Tape and Reel Package Marking 0.8 STD LP3990SD-0.8 LP3990SDX-0.8 L085B 1.2* STD LP3990SD-1.2 LP3990SDX-1.2 L086B 1.35* STD LP3990SD-1.35 LP3990SDX-1.35 L150B 1.5 STD LP3990SD-1.5 LP3990SDX-1.5 L087B 1.8 STD LP3990SD-1.8 LP3990SDX-1.8 L088B 2.5 STD LP3990SD-2.5 LP3990SDX-2.5 L090B 2.8* STD LP3990SD-2.8 LP3990SDX-2.8 L091B 3.3* STD LP3990SD-3.3 LP3990SDX-3.3 L092B For SOT23 - 5 Package * Please contact Sales Office for Availability Output Voltage (V) Grade LP3990 Supplied as 1000 Units, Tape and Reel LP3990 Supplied as 3000 Units, Tape and Reel Package Marking 0.8* STD LP3990MF-0.8 LP3990MFX-0.8 SCCB 1.2* STD LP3990MF-1.2 LP3990MFX-1.2 SCDB 1.35* STD LP3990MF-1.35 LP3990MFX-1.35 SHRB 1.5* STD LP3990MF-1.5 LP3990MFX-1.5 SCEB 1.8* STD LP3990MF-1.8 LP3990MFX-1.8 SCFB 2.5* STD LP3990MF-2.5 LP3990MFX-2.5 SCJB 2.8* STD LP3990MF-2.8 LP3990MFX-2.8 SCKB 3.3* STD LP3990MF-3.3 LP3990MFX-3.3 SCLB www.national.com 4 ESD (Note 5) (Notes 1, 2) Human Body Model If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Machine Model Input Voltage Operating Ratings(Note 1) -0.3 to 6.5V Output Voltage -0.3 to (VIN + 0.3V) to 6.5V (max) Enable Input Voltage -0.3 to (VIN + 0.3V) to 6.5V (max) Junction Temperature Input Voltage 235˚C 260˚C Storage Temperature 0 to (VIN + 0.3V) to 6.0V (max) Junction Temperature -40˚C to 125˚C Ambient Temperature TARange (Note 6) Lead/Pad Temp. (Note 3) micro SMD 2V to 6V Enable Input Voltage 150˚C LLP/SOT23 2KV 200V -40˚C to 85˚C Thermal Properties(Note 1) -65 to 150˚C Junction To Ambient Thermal Resistance(Note 8) Continuous Power Dissipation Internally Limited(Note 4) θJA(LLP-6) 88˚C/W θJA(microSMD) 220˚C/W θJASOT23-5 220˚C/W Electrical Characteristics Unless otherwise noted, VEN =950mV, VIN = VOUT + 1.0V, or 2.0V, whichever is higher. CIN = 1 µF, IOUT = 1 mA, COUT =0.47 µF. Typical values and limits appearing in normal type apply for TJ = 27˚C. Limits appearing in boldface type apply over the full junction temperature range for operation, −40 to +125˚C. (Note 13) Symbol Parameter Conditions VIN Input Voltage (Note 14) ∆VOUT Output Voltage Tolerance ILOAD = 1 mA Over full line and load regulation. Typ Limit Min 2 6 -1 +1 LLP -1.5 +1.5 Micro SMD -2.5 +2.5 -3 +3 Micro SMD LLP Units Max V % Line Regulation Error VIN = (VOUT(NOM) + 1.0V) to 6.0V, 0.02 -0.1 0.1 Load Regulation Error IOUT = 1mA to 150mA VOUT = 0.8 to 1.95V MicroSMD 0.002 -0.005 0.005 VOUT = 0.8 to 1.95V LLP, SOT-23 0.003 -0.008 0.008 VOUT = 2.0 to 3.3V MicroSMD 0.0005 -0.002 0.002 VOUT = 2.0 to 3.3V LLP, SOT-23 0.002 -0.005 0.005 VDO Dropout Voltage IOUT = 150mA (Note 7) 120 ILOAD Load Current (Notes 9, 10) IQ Quiescent Current VEN = 950mV, IOUT = 0mA 43 80 VEN = 950mV, IOUT = 150mA 65 120 Short Circuit Current Limit IOUT Maximum Output Current PSRR Power Supply Rejection Ratio (Note 11) 0.2 550 1000 150 55 f = 10kHz, IOUT = 150mA 35 5 µA 0.002 f = 1kHz, IOUT = 1mA to 150mA %/mA mV 0 VEN = 0.4V ISC %/V µA mA mA dB www.national.com LP3990 Absolute Maximum Ratings LP3990 Electrical Characteristics (Continued) Unless otherwise noted, VEN =950mV, VIN = VOUT + 1.0V, or 2.0V, whichever is higher. CIN = 1 µF, IOUT = 1 mA, COUT =0.47 µF. Typical values and limits appearing in normal type apply for TJ = 27˚C. Limits appearing in boldface type apply over the full junction temperature range for operation, −40 to +125˚C. (Note 13) Symbol en Parameter Output noise Voltage (Note 10) TSHUTDOWN Thermal Shutdown Conditions BW = 10Hz to 100kHz, Typ VOUT = 0.8 60 VOUT = 1.5 125 VOUT = 3.3 180 Temperature 155 Hysteresis 15 0.001 Limit Min Max Units µVRMS ˚C Enable Control Characteristics IEN (Note 12) Maximum Input Current at VEN Input VEN = 0.0V VIL Low Input Threshold VIN = 2V to 6V VIH High Input Threshold VIN = 2V to 6V VEN = 6V 6 0.1 2.5 10 0.4 0.95 µA V V Timing Characteristics TON Transient Response Turn On Time (Note 10) VOUT = 0.8 To 95% Level VIN(MIN) to 6.0V VOUT = 1.5 80 150 105 200 VOUT = 3.3 175 250 8 16 mV (pk - pk) 55 80 mV Line Transient Response |δVOUT| Trise = Tfall = 30µs (Note 10) δVIN = 600mV Load Transient Response |δVOUT| Trise = Tfall = 1µs (Note 10)IOUT = 1mA to 150mA COUT = 1µF µs Note 1: Absolute Maximum Ratings are limits beyond which damage can occur. Operating Ratings are conditions under which operation of the device is guaranteed. Operating Ratings do not imply guaranteed performance limits. For guaranteed performance limits and associated test conditions, see the Electrical Characteristics tables. Note 2: All Voltages are with respect to the potential at the GND pin. Note 3: For further information on these packages please refer to the following application notes;AN-1112 Micro SMD Package Wafer Level Chip Scale Package,AN-1187 Leadless Leadframe Package. Note 4: Internal thermal shutdown circuitry protects the device from permanent damage. Note 5: The human body model is 100pF discharged through a 1.5kΩ resistor into each pin. The machine model is a 200pF capacitor discharged directly into each pin. Note 6: The maximum ambient temperature (TA(max)) is dependant on the maximum operating junction temperature (TJ(max-op) = 125˚C), the maximum power dissipation of the device in the application (PD(max)), and the junction to ambient thermal resistance of the part/package in the application (θJA), as given by the following equation: TA(max) = TJ(max-op) - (θJA x PD(max)). Note 7: Dropout voltage is voltage difference between input and output at which the output voltage drops to 100mV below its nominal value. This parameter only for output voltages above 2.0V. Note 8: Junction to ambient thermal resistance is dependant on the application and board layout. In applications where high maximum power dissipation is possible, special care must be paid to thermal dissipation issues in board design. Note 9: The device maintains the regulated output voltage without the load. Note 10: This electrical specification is guaranteed by design. Note 11: Short circuit current is measured with VOUT pulled to 0V and VIN worst case = 6.0V. Note 12: Enable Pin has 1MΩ typical, resistor connected to GND. Note 13: All limits are guaranteed. All electrical characteristics having room-temperature limits are tested during production at TJ = 25˚C or correlated using Statistical Quality Control methods. Operation over the temperature specification is guaranteed by correlating the electrical characteristics to process and temperature variations and applying statistical process control. Note 14: VIN(MIN) = VOUT(NOM) + 0.5V, or 2.0V, whichever is higher. Output Capacitor, Recommended Specifications Symbol COUT Parameter Output Capacitor Conditions Capacitance (Note 15) Limit Min -40˚C to +125˚C 1.0 0.68 0˚C to +125˚C 0.47 0.33 ESR www.national.com Typ 5 6 Max Units µF 500 mΩ (Continued) Note 15: The capacitor tolerance should be 30% or better over temperature. The full operating conditions for the application should be considered when selecting a suitable capacitor to ensure that the minimum value of capacitance is always met. Recommended capacitor type is X7R. However, dependent on application, X5R, Y5V, and Z5U can also be used. (See capacitor section in Applications Hints) Typical Performance Characteristics. Unless otherwise specified, CIN = 1.0µF Ceramic, COUT = 0.47 µF Ceramic, VIN = VOUT(NOM) + 1.0V, TA = 25˚C, VOUT(NOM) = 1.5V , Shutdown pin is tied to VIN. Output Voltage Change vs Temperature Ground Current vs Load Current 20076831 20076810 Ground Current vs VIN. ILOAD = 0mA Ground Current vs VIN. ILOAD = 1mA 20076812 20076813 7 www.national.com LP3990 Output Capacitor, Recommended Specifications LP3990 Typical Performance Characteristics. Unless otherwise specified, CIN = 1.0µF Ceramic, COUT = 0.47 µF Ceramic, VIN = VOUT(NOM) + 1.0V, TA = 25˚C, VOUT(NOM) = 1.5V , Shutdown pin is tied to VIN. (Continued) Ground Current vs VIN. ILOAD = 150mA Short Circuit Current 20076815 20076814 Short Circuit Current Line transient 20076817 20076816 Power Supply Rejection Ratio Power Supply Rejection Ratio 20076819 www.national.com 20076820 8 Enable Start-up Time Enable Start-up Time 20076821 20076822 Load Transient Noise Density 20076825 20076828 9 www.national.com LP3990 Typical Performance Characteristics. Unless otherwise specified, CIN = 1.0µF Ceramic, COUT = 0.47 µF Ceramic, VIN = VOUT(NOM) + 1.0V, TA = 25˚C, VOUT(NOM) = 1.5V , Shutdown pin is tied to VIN. (Continued) LP3990 In particular, the output capacitor selection should take account of all the capacitor parameters, to ensure that the specification is met within the application. The capacitance can vary with DC bias conditions as well as temperature and frequency of operation. Capacitor values will also show some decrease over time due to aging. The capacitor parameters are also dependant on the particular case size, with smaller sizes giving poorer performance figures in general. As an example, Figure 1 shows a typical graph comparing different capacitor case sizes in a Capacitance vs. DC Bias plot. As shown in the graph, increasing the DC Bias condition can result in the capacitance value falling below the minimum value given in the recommended capacitor specifications table (0.33µF in this case). Note that the graph shows the capacitance out of spec for the 0402 case size capacitor at higher bias voltages. It is therefore recommended that the capacitor manufacturers’ specifications for the nominal value capacitor are consulted for all conditions, as some capacitor sizes (e.g. 0402) may not be suitable in the actual application. Application Hints EXTERNAL CAPACITORS In common with most regulators, the LP3990 requires external capacitors for regulator stability. The LP3990 is specifically designed for portable applications requiring minimum board space and smallest components. These capacitors must be correctly selected for good performance. INPUT CAPACITOR An input capacitor is required for stability. It is recommended that a 1.0µF capacitor be connected between the LP3990 input pin and ground (this capacitance value may be increased without limit). This capacitor must be located a distance of not more than 1cm from the input pin and returned to a clean analogue ground. Any good quality ceramic, tantalum, or film capacitor may be used at the input. Important: Tantalum capacitors can suffer catastrophic failures due to surge current when connected to a lowimpedance source of power (like a battery or a very large capacitor). If a tantalum capacitor is used at the input, it must be guaranteed by the manufacturer to have a surge current rating sufficient for the application. There are no requirements for the ESR (Equivalent Series Resistance) on the input capacitor, but tolerance and temperature coefficient must be considered when selecting the capacitor to ensure the capacitance will remain ) 1.0µF over the entire operating temperature range. OUTPUT CAPACITOR The LP3990 is designed specifically to work with very small ceramic output capacitors. A 0.47µF ceramic capacitor (temperature types Z5U, Y5V or X7R) with ESR between 5mΩ to 500mΩ, is suitable in the LP3990 application circuit. For this device the output capacitor should be connected between the VOUT pin and ground. It is also possible to use tantalum or film capacitors at the device output, COUT (or VOUT), but these are not as attractive for reasons of size and cost (see the section Capacitor Characteristics). The output capacitor must meet the requirement for the minimum value of capacitance and also have an ESR value that is within the range 5mΩ to 500mΩ for stability. 20076840 FIGURE 1. Graph Showing a Typical Variation in Capacitance vs DC Bias The ceramic capacitor’s capacitance can vary with temperature. The capacitor type X7R, which operates over a temperature range of -55˚C to +125˚C, will only vary the capacitance to within ± 15%. The capacitor type X5R has a similar tolerance over a reduced temperature range of -55˚C to +85˚C. Many large value ceramic capacitors, larger than 1µF are manufactured with Z5U or Y5V temperature characteristics. Their capacitance can drop by more than 50% as the temperature varies from 25˚C to 85˚C. Therefore X7R is recommended over Z5U and Y5V in applications where the ambient temperature will change significantly above or below 25˚C. Tantalum capacitors are less desirable than ceramic for use as output capacitors because they are more expensive when comparing equivalent capacitance and voltage ratings in the 0.47µF to 4.7µF range. Another important consideration is that tantalum capacitors have higher ESR values than equivalent size ceramics. This means that while it may be possible to find a tantalum capacitor with an ESR value within the stable range, it would have to be larger in capacitance (which means bigger and more costly) than a ceramic capacitor with the same ESR value. It should also be noted that the ESR of a typical NO-LOAD STABILITY The LP3990 will remain stable and in regulation with no external load. This is an important consideration in some circuits, for example CMOS RAM keep-alive applications. CAPACITOR CHARACTERISTICS The LP3990 is designed to work with ceramic capacitors on the output to take advantage of the benefits they offer. For capacitance values in the range of 0.47µF to 4.7µF, ceramic capacitors are the smallest, least expensive and have the lowest ESR values, thus making them best for eliminating high frequency noise. The ESR of a typical 0.47µF ceramic capacitor is in the range of 20mΩ to 40mΩ, which easily meets the ESR requirement for stability for the LP3990. For both input and output capacitors, careful interpretation of the capacitor specification is required to ensure correct device operation. The capacitor value can change greatly, depending on the operating conditions and capacitor type. www.national.com 10 Micro SMD MOUNTING (Continued) The micro SMD package requires specific mounting techniques, which are detailed in National Semiconductor Application Note AN-1112. For best results during assembly, alignment ordinals on the PC board may be used to facilitate placement of the micro SMD device. tantalum will increase about 2:1 as the temperature goes from 25˚C down to -40˚C, so some guard band must be allowed. ENABLE CONTROL The LP3990 features an active high Enable pin, VEN, which turns the device on when pulled high. When not enabled the regulator output is off and the device typically consumes 2nA. If the application does not require the Enable switching feature, the VEN pin should be tied to VIN to keep the regulator output permanently on. Micro SMD LIGHT SENSITIVITY Exposing the micro SMD device to direct light may affect the operation of the device. Light sources, such as halogen lamps, can affect electrical performance, if placed in close proximity to the device. Light with wavelengths in the infra-red portion of the spectrum is the most detrimental, and so, fluorescent lighting used inside most buildings, has little or no effect on performance. To ensure proper operation, the signal source used to drive the VEN input must be able to swing above and below the specified turn-on/off voltage thresholds listed in the Electrical Characteristics section under VIL and VIH. 11 www.national.com LP3990 Application Hints LP3990 Physical Dimensions inches (millimeters) unless otherwise noted micro SMD, 4 Bump, Package (TLA04) NS Package Number TLA04ALA The dimensions for X1, X2 and X3 are given as: X1 = 1.003 +/− 0.03mm X2 = 1.283 +/− 0.03mm X3 = 0.600 +/− 0.075mm LLP, 6 Lead, Package (SOT23 Land) NS Package Number SDE06A www.national.com 12 inches (millimeters) unless otherwise noted (Continued) SOT23 - 5 Package NS Package Number MF05A National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: [email protected] National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: [email protected] Tel: 81-3-5639-7560 LP3990 150mA Linear Voltage Regulator for Digital Applications Physical Dimensions