Agilent HLMP-Cxxx T-13/4 (5 mm) Extra Bright Precision Optical Performance InGaN LED Lamps Data Sheet Features HLMP-CB11, HLMP-CB12, HLMP-CM11, HLMP-CM12, HLMP-CE11, HLMP-CE12, HLMP-CB26, HLMP-CB27, HLMP-CM26, HLMP-CM27, HLMP-CE26, HLMP-CE27, HLMP-CB36, HLMP-CB37, HLMP-CM36, HLMP-CM37, HLMP-CE36, HLMP-CE37 Description These high intensity blue and green LEDs are based on the most efficient and cost effective InGaN material technology. The 470 nm typical dominant wave– length for blue and 525 nm typical wavelength for green is well suited to color mixing in full color signs. The 505 nm typical dominant wavelength for cyan is suitable for traffic signal application. These LED lamps are untinted, non-diffused, T-13/4 packages incorporating second generation optics which produce well-defined spatial radiation patterns at specific viewing cone angles. These lamps are made with an advanced optical grade epoxy, offering superior temperature and moisture resistance in outdoor signal and sign applications. The high maximum LED junction temperature limit of +110 ° C enables high temperature operation in bright sunlight conditions. • Well defined spatial radiation pattern • High luminous output • Available in blue, green, and cyan color • Viewing angle: 15°, 23° and 30 ° • Standoff or non-standoff leads • Superior resistance to moisture Applications • • • • Traffic signals Commercial outdoor advertising Front panel backlighting Front panel indicator CAUTION: Devices are Class I ESD sensitive. Please observe appropriate precautions during handling and processing. Refer to Application Note AN-1142 for additional details. Package Dimensions Package A 2.35 (0.093) MAX. 1.14 ± 0.20 (0.045 ± 0.008) 5.00 ± 0.20 (0.197 ± 0.008) ∅ 5.80 ± 0.20 (0.228 ± 0.008) 0.50 ± 0.10 SQ. TYP. (0.020 ± 0.004) 0.70 (0.028) MAX. 2.54 ± 0.38 (0.100 ± 0.015) NOTE 1 CATHODE LEAD 8.71 ± 0.20 (0.343 ± 0.008) 1.00 MIN. (0.039) CATHODE FLAT 31.60 MIN. (1.244) Package B ∅ 5.80 ± 0.20 (0.228 ± 0.008) 1.14 ± 0.20 (0.045 ± 0.008) 1.50 ± 0.15 (0.059 ± 0.006) 0.70 (0.028) MAX. 0.50 ± 0.10 SQ. TYP. (0.020 ± 0.004) 5.00 ± 0.20 NOTE 1 (0.197 ± 0.008) 2.54 ± 0.38 (0.100 ± 0.015) CATHODE LEAD 8.71 ± 0.20 (0.343 ± 0.008) 1.00 MIN. (0.039) DIMENSION H (REFER TO TABLE BELOW) 31.60 MIN. (1.244) DIMENSION H: 15° = 11.40 ± 0.25 mm (0.449 ± 0.01 INCH) 23° = 11.85 ± 0.25 mm (0.467 ± 0.01 INCH) 30° = 11.50 ± 0.25 mm (0.453 ± 0.01 INCH) NOTES: 1. MEASURED JUST ABOVE FLANGE. 2. ALL DIMENSIONS ARE IN MILLIMETERS (INCHES). 3. EPOXY MENISCUS MAY EXTEND ABOUT 1 mm (0.040") DOWN THE LEADS. 4. IF HEAT SINKING APPLICATION IS REQUIRED, THE TERMINAL FOR HEAT SINK IS ANODE. 2 CATHODE FLAT Device Selection Guide Part Number Color Typical Viewing Angle, 2q1/2 (Degree) HLMP-CB11-TW0xx Blue 15 2.5 7.2 No A Clear HLMP-CB11-UVAxx Blue 15 3.2 5.5 No A Clear HLMP-CB12-TW0xx Blue 15 2.5 7.2 Yes B Clear HLMP-CM11-Y20xx Green 15 9.3 27.0 No A Clear HLMP-CM11-Z1Cxx Green 15 12.0 21.0 No A Clear HLMP-CM12-Y20xx Green 15 9.3 27.0 Yes B Clear HLMP-CE11-X10xx Cyan 15 7.2 21.0 No A Clear HLMP-CE12-X10xx Cyan 15 7.2 21.0 Yes B Clear HLMP-CB26-SV0xx Blue 23 1.9 5.5 No A Clear HLMP-CB26-TUDxx Blue 23 2.5 4.2 No A Clear HLMP-CB27-SV0xx Blue 23 1.9 5.5 Yes B Clear HLMP-CM26-X10xx Green 23 7.2 21.0 No A Clear HLMP-CM26-YZCxx Green 23 9.3 16.0 No A Clear HLMP-CM27-X10xx Green 23 7.2 21.0 Yes B Clear HLMP-CE26-WZ0xx Cyan 23 5.5 16.0 No A Clear HLMP-CE27-WZ0xx Cyan 23 5.5 16.0 Yes B Clear HLMP-CB36-QT0xx Blue 30 1.15 3.2 No A Clear HLMP-CB36-RSAxx Blue 30 1.5 2.5 No A Clear HLMP-CB37-RU0xx Blue 30 1.5 4.2 Yes B Clear HLMP-CB37-RSDxx Blue 30 1.5 2.5 Yes B Clear HLMP-CM36-X10xx Green 30 7.2 21.0 No A Clear HLMP-CM36-XYCxx Green 30 7.2 12.0 No A Clear HLMP-CM37-X10xx Green 30 7.2 21.0 Yes B Clear HLMP-CM37-XYCxx Green 30 7.2 12.0 Yes B Clear HLMP-CM37-XYDxx Green 30 7.2 12.0 Yes B Clear HLMP-CE36-WZ0xx Cyan 30 5.5 16.0 No A Clear HLMP-CE37-WZ0xx Cyan 30 5.5 16.0 Yes B Clear Intensity (cd) at 20 mA Min. Max. Standoff Package Dimension Lens Notes: 1. Tolerance for luminous intensity measurement is ±15%. 2. The luminous intensity is measured on the mechanical axis of the lamp package. 3. The optical axis is closely aligned with the package mechanical axis. 4. LED light output is bright enough to cause injuries to the eyes. Precautions must be taken to prevent looking directly at the LED without proper safety equipment. 5. 2q1/2 is the off-axis angle where the luminous intensity is 1/2 the on-axis intensity. 3 Part Numbering System HLMP - x x xx - x x x xx Mechanical Options 00: Bulk DD: Ammo Pack Color Bin Options 0: Full Color Bin Distribution A: Color Bin 1 and 2 C: Color Bin 3 and 4 D: Color Bin 4 and 5 Maximum Intensity Bin 0: No Maximum Intensity Bin Limitation Others: Refer to Device Selection Guide Minimum Intensity Bin Refer to Device Selection Guide Viewing Intensity Bin 11: 15° Without Standoff 12: 15° With Standoff 26: 23° Without Standoff 27: 23° With Standoff 36: 30° Without standoff 37: 30° With Standoff Color B: Blue 470 nm M: Green 525 nm E: Cyan 505 nm Package C: T-13/4 (5 mm) Round Lamp 4 Absolute Maximum Rating at TA = 25°C Parameters Value Unit 30 mA 100 mA Average Forward Current 30 mA Power Dissipation 120 mW LED Junction Temperature 110 °C Operating Temperature Range –40 to +85 °C Storage Temperature Range –40 to +100 °C Wave Soldering Temperature[2] 250 for 3 secs °C DC Forward Current [1] Peak Pulsed Forward Current[3] Notes: 1. Derate linearly as shown in Figure 2. 2. 1.59 mm (0.060 inch) below body. 3. Duty factor 10%, frequency 1 KHz. Electrical/Optical Characteristics TA = 25o C Blue Parameters Symbol Forward Voltage VF Reverse Voltage[1] VR Min. Typ. Max. Green Min. Typ. Max. 3.5 4.0 5.0 Cyan Min. Typ. Max. Units Test Condition 3.5 4.0 V IF = 20 mA V IR = 10 µA 240 o C/W LED Junction to Anode Lead 490 505 510 nm IF = 20 mA 3.6 4.0 5.0 240 5.0 Thermal Resistance RqJ-PIN Dominant Wavelength[2] ld Peak Wavelength lPEAK 464 516 501 nm Peak of Wavelength of Spectral Distribution at IF = 20 mA Spectral Half Width Dl1/2 23 32 30 nm Wavelength Width at Spectral Distribution Power Point at IF = 20 mA Luminous Efficacy[3] hv 74 484 319 lm/W Emitted Luminous Power/Emitted Radiant Power 460 470 480 240 520 525 540 Notes: 1. The reverse voltage of the product is equivalent to the forward voltage of the protective chip at I R = 10 µA. 2. The dominant wavelength, ld, is derived from the Chromaticity Diagram and represents the color of the lamp. 3. The radiant intensity, Ie in watts/steradian, may be found from the equation Ie = Iv/h v, where Iv is the luminous intensity in candelas and hv is the luminous efficacy in lumens/watt. 5 1.00 40 IF – FORWARD CURRENT – mA CYAN RELATIVE INTENSITY 0.80 GREEN BLUE 0.60 0.40 0.20 0 350 20 RΘJ-A = 780 °C/W 10 0 400 450 500 550 600 650 RΘJ-A = 585 °C/W 30 0 WAVELENGTH – nm Figure 1. Relative intensity vs. wavelength. RELATIVE DOMINANT WAVELENGTH (NORMALIZED AT 20 mA) FORWARD CURRENT – mA BLUE 20 10 GREEN 0 1.0 4.0 3.0 2.0 80 100 Figure 3. Forward current vs. forward voltage. 1.6 1.4 1.2 1.0 0.8 GREEN 0.6 0.4 BLUE 0.2 0 0 5 10 15 20 1.020 GREEN 1.015 1.010 1.005 BLUE 1.000 0.995 0.990 0 10 20 30 DC FORWARD CURRENT – mA FORWARD VOLTAGE – V RELATIVE INTENSITY (NORMALIZED AT 20 mA) 60 1.025 CYAN 25 30 FORWARD CURRENT – mA Figure 5. Relative intensity vs. DC forward current. 6 40 Figure 2. Forward current vs. ambient temperature. 30 0 20 VF – FORWARD VOLTAGE – VOLTS Figure 4. Relative dominant wavelength vs. DC forward current. RELATIVE LUMINOUS INTENSITY 1 0.5 0 -90 -60 -30 0 30 60 90 60 90 60 90 ANGULAR DISPLACEMENT – DEGREES Figure 6. Spatial radiation pattern for Cx11 and Cx12. RELATIVE LUMINOUS INTENSITY 1 0.5 0 -90 -60 -30 0 30 ANGULAR DISPLACEMENT – DEGREES Figure 7. Spatial radiation pattern for Cx26 and Cx27. RELATIVE LUMINOUS INTENSITY 1 0.5 0 -90 -60 -30 0 30 ANGULAR DISPLACEMENT – DEGREES Figure 8. Spatial radiation pattern for Cx36 and Cx37. 7 Intensity Bin Limit Table Blue Color Bin Table Intensity (mcd) at 20 mA Bin Min Dom Max Dom Xmin Ymin Xmax Ymax Bin Min Max 1 460.0 464.0 0.1440 0.0297 0.1766 0.0966 N 680 880 0.1818 0.0904 0.1374 0.0374 2 464.0 468.0 0.1374 0.0374 0.1699 0.1062 0.1766 0.0966 0.1291 0.0495 0.1291 0.0495 0.1616 0.1209 0.1699 0.1062 0.1187 0.0671 0.1187 0.0671 0.1517 0.1423 0.1616 0.1209 0.1063 0.0945 0.1063 0.0945 0.1397 0.1728 0.1517 0.1423 0.0913 0.1327 P 880 1150 Q 1150 1500 R 1500 1900 S 1900 2500 T 2500 3200 U 3200 4200 V 4200 5500 W 5500 7200 X 7200 9300 Y 9300 12000 Z 12000 16000 Green Color Bin Table 1 16000 21000 Bin Min Dom Max Dom Xmin Ymin Xmax Ymax 1 520.0 524.0 0.0743 0.8338 0.1856 0.6556 0.1650 0.6586 0.1060 0.8292 0.1060 0.8292 0.2068 0.6463 0.1856 0.6556 0.1387 0.8148 0.1387 0.8148 0.2273 0.6344 0.2068 0.6463 0.1702 0.7965 0.1702 0.7965 0.2469 0.6213 0.2273 0.6344 0.2003 0.7764 0.2003 0.7764 0.2659 0.6070 0.2469 0.6213 0.2296 0.7543 Tolerance for each bin limit is ±15%. 3 4 5 468.0 472.0 476.0 472.0 476.0 480.0 Tolerance for each bin limit is ±0.5 nm. 2 3 4 5 524.0 528.0 532.0 536.0 528.0 532.0 536.0 540.0 Tolerance for each bin limit is ±0.5 nm. Cyan Color Bin Table Bin Min Dom Max Dom Xmin Ymin Xmax Ymax 1 490.0 495.0 0.0454 0.2945 0.1164 0.3889 0.1318 0.306 0.0235 0.4127 0.0345 0.4127 0.1057 0.4769 0.1164 0.3889 0.0082 0.5384 0.0082 0.5384 0.1027 0.5584 0.1057 0.4769 0.0039 0.6548 0.0039 0.6548 0.1097 0.6251 0.1027 0.5584 0.0139 0.7502 0.0132 0.4882 0.1028 0.5273 0.1092 0.4417 0.0040 0.6104 0.0040 0.6104 0.1056 0.6007 0.1028 0.5273 0.0080 0.7153 2 3 4 7 8 495.0 500.0 505.0 498.0 503.0 500.0 505.0 510.0 503.0 508.0 Tolerance for each bin limit is ±0.5 nm. 8 www.agilent.com/semiconductors For product information and a complete list of distributors, please go to our web site. For technical assistance call: Americas/Canada: +1 (800) 235-0312 or (916) 788-6763 Europe: +49 (0) 6441 92460 China: 10800 650 0017 Hong Kong: (+65) 6756 2394 India, Australia, New Zealand: (+65) 6755 1939 Japan: (+81 3) 3335-8152(Domestic/International), or 0120-61-1280(Domestic Only) Korea: (+65) 6755 1989 Singapore, Malaysia, Vietnam, Thailand, Philippines, Indonesia: (+65) 6755 2044 Taiwan: (+65) 6755 1843 Data subject to change. Copyright © 2004 Agilent Technologies, Inc. December 7, 2004 5989-1022EN