LM4858 Mono 1.5 W / Stereo 300mW Power Amplifier General Description Key Specifications The LM4858 is an audio power amplifier capable of delivering 1.5W (typ) of continuous average power into a mono 4Ω bridged-tied load (BTL) with 1% THD+N or 95mW per channel of continuous average power into stereo 32Ω singleended (SE) loads with 1% THD+N, using a 5V power supply. The LM4858 can automatically switch between mono BTL and stereo SE modes utilizing a headphone sense pin. It is ideal for any system that provides both a monaural speaker output and a stereo line or headphone output n n n n n n n n n n Boomer audio power amplifiers were designed specifically to provide high quality output power with a minimal amount of external components. Since the LM4858 does not require bootstrap capacitors or snubber networks, it is optimally suited for low-power portable systems. The LM4858 features an externally controlled, micropower consumption shutdown mode and thermal shutdown protection. The unity-gain stable LM4858’s gain is set by external gain-setting resistors Output Power at 1% THD+N, 1kHz: LM4858LD 3Ω BTL LM4858LD 4Ω BTL LM4858MM 4Ω BTL LM4858MM,LD 8Ω BTL LM4858MM,LD 8Ω SE LM4858MM,LD 32Ω SE THD+N at 1kHz, 95mW into 32Ω SE Single Supply Operation Shutdown Current 1.9W (typ) 1.7W (typ) 1.5W (typ) 1.1W (typ) 300mW (typ) 95mW (typ) 1% (typ) 2.4 to 5.5V 18µA (typ) Features n n n n n n n Mono 1.5W BTL or stereo 300mW output Logic controlled headphone sense “Click and pop” suppression circuitry No bootstrap capacitors required Thermal shutdown protection Unity-gain stable Available in space-saving MSOP and LLP packaging Applications n n n n Portable computers Desktop computers PDA’s Handheld games Connection Diagrams 20064729 Top View 10 Lead MSOP Order Number LM4858MM See NS Package Number MUB10A 20064728 Top View 14 Lead LLP Order Number LM4858LD See NS Package Number LDA14A Boomer ® is a registered trademark of National Semiconductor Corporation. © 2003 National Semiconductor Corporation DS200647 www.national.com LM4858 Mono 1.5 W / Stereo 300mW Power Amplifier May 2003 LM4858 Typical Application 20064731 FIGURE 1. Typical Audio Amplifier Application Circuit www.national.com 2 Thermal Resistance (Note 2) θJA (typ) — MUB10A If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage 6.0V Storage Temperature 52˚C/W θJA (typ) — LDA14A (Note 10) 56˚C/W θJC (typ) — LDA14A 4.3˚C/W −65˚C to +150˚C ESD Susceptibility (Note 4) 3.5kV ESD Machine model (Note 7) 250V Junction Temperature (TJ) 194˚C/W θJC (typ) — MUB10A Operating Ratings (Note 2) Temperature Range 150˚C −40˚C ≤ to 85˚C Solder Information (Note 1) 2.4V ≤ VDD ≤ 5.5V Supply Voltage VDD Small Outline Package Vapor Phase (60 sec.) 215˚C Infrared (15 sec.) 220˚C Note 1: See AN-450 "Surface Mounting and their effects on Product Reliability" for other methods of soldering surface mount devices. Electrical Characteristics (Notes 2, 8) The following specifications apply for VDD= 5.0V, TA= 25˚C unless otherwise specified. Symbol Parameter Conditions LM4858 Typical (Note 5) VDD Supply Voltage Limit (Note 6) Units (Limits) 2.4 V (min) 5.5 V (max) IDD Supply Current BTL Mode; VIN = 0V; IO = 0A 2.4 7.0 mA SE Mode; VIN = 0V; IO = 0A 2.4 7.0 mA ISD Shutdown Current SD Mode; VSHUTDOWN = VDD 18 VOS Output Offset Voltage BTL Mode; AV = 2 BTL OUT+ to BTL OUT− 5.0 40 mV PO Output Power BTL Mode; RL = 3Ω THD+N = 1%; LM4858LD 1.9 W BTL Mode; RL = 4Ω THD+N = 1%; LM4858LD 1.7 W BTL Mode; RL = 4Ω THD+N = 1%; LM4858MM 1.5 W BTL Mode; RL = 8Ω THD+N = 1%; LM4858MM, LD 1.1 W SE Mode; RL = 8Ω THD+N = 1%; LM4858MM, LD 300 mW SE Mode; RL = 32Ω THD+N = 1%; LM4858MM, LD 95 mW µA VIH Input Voltage High SHUTDOWN, HP-IN 2.0 V (min) VIL Input Voltage Low SHUTDOWN, HP-IN 0.8 V (max) Crosstalk Channel Seperation SE Mode, RL = 32Ω; f = 1kHz 3 73 dB www.national.com LM4858 Absolute Maximum Ratings LM4858 Electrical Characteristics (Notes 2, 8) The following specifications apply for VDD= 3.3V, TA= 25˚C unless otherwise specified. Symbol Parameter Conditions LM4858 Typical (Note 5) IDD Supply Current Limit (Note 6) Units (Limits) BTL Mode; VIN = 0V; IO = 0A 2.0 mA SE Mode; VIN = 0V; IO = 0A 2.0 mA µA ISD Shutdown Current SD Mode; VSHUTDOWN = VDD 12 VOS Output Offset Voltage BTL Mode; AV = 2 BTL OUT+ to BTL OUT− 5.0 PO Output Power BTL Mode; RL = 8Ω THD+N = 1% 440 mW SE Mode; RL = 32Ω THD+N = 1% 40 mW 40 mV VIH Input Voltage High SHUTDOWN, HP-IN 2.0 V (min) VIL Input Voltage Low SHUTDOWN, HP-IN 0.8 V (max) Electrical Characteristics (Notes 2, 8) The following specifications apply for VDD= 2.7V, TA= 25˚C unless otherwise specified. Symbol Parameter Conditions LM4858 Typical (Note 5) IDD Supply Current Limit (Note 6) Units (Limits) BTL Mode; VIN = 0V; IO = 0A 1.8 mA SE Mode; VIN = 0V; IO = 0A 1.8 mA µA ISD Shutdown Current SD Mode; VSHUTDOWN = VDD 10 VOS Output Offset Voltage BTL Mode; AV = 2 BTL OUT+ to BTL OUT− 5.0 PO Output Power BTL Mode; RL = 8Ω THD+N = 1% 300 mW SE Mode; RL = 32Ω THD+N = 1% 25 mW 40 mV VIH Shutdown Input Voltage High SHUTDOWN, HP-IN 2.0 V (min) VIL Shutdown Input Voltage Low SHUTDOWN, HP-IN 0.8 V (max) Note 2: Absolute Maximum Rating indicate limits beyond which damage to the device may occur. Note 3: Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. Note 4: Human body model, 100pF discharged through a 1.5kΩ resistor. Note 5: Typical specifications are specified at +25˚C and represent the most likely parametric norm. Note 6: Datasheet min/max specification limits are guaranteed by design, test, or statistical analysis. Note 7: Machine Model ESD test is covered by specification EIAJ IC-121-1981. A 200pF cap is charged to the specified voltage, then discharged directly into the IC with no external series resistor (resistance of discharge path must be under 50Ω). Note 8: All voltages are measured with respect to the ground pin, unless otherwise specified. Note 9: Limits are guaranteed to National’s AOQL ( Average Outgoing Quality Level ). Note 10: The given θJA is for an LM4858LD with the Exposed-DAP soldered to an exposed 1in2 area of 1oz printed circuit board copper. www.national.com 4 LM4858 External Components Description See Figure 1. Components Functional Description 1. Ri Inverting input resistance which sets the closed-loop gain in conjunction with Rf. This resistor also forms a high pass filter with Ci at fc = 1/(2πRiCi). 2. Ci Input coupling capacitor which blocks the DC voltage at the amplifier’s input terminals. Also creates a highpass filter with Ri at fc = 1/(2πRiCi). Refer to the section, Proper Selection of External Components, for an explanation of how to determine the value of Ci. 3. Rf Feedback resistance which sets the closed-loop gain in conjunction with Ri. 4. Cs Supply bypass capacitor which provides power supply filtering. Refer to the Power Supply Bypassing section for information concerning proper placement and selection of the supply bypass capacitor. 5. CB Bypass pin capacitor which provides half-supply filtering. Refer to the section, Proper Selection of External Components, for information concerning proper placement and selection of CB. 6. CO Output coupling capacitor which blocks the DC voltage at the amplifier’s output. Forms a high pass filter with the single-ended load RL at fO = 1/(2π RLCO). Typical Performance Characteristics LD Specific Characteristics LM4858LD THD+N vs Frequency LM4858LD THD+N vs Frequency 200647A5 200647A6 LM4858LD THD+N vs Output Power LM4858LD THD+N vs Output Power 200647A7 200647A8 5 www.national.com LM4858 Typical Performance Characteristics LD Specific Characteristics (Continued) LM4858LD Power Dissipation vs Output Power LM4858LD Power Derating Curve 200647A9 200647B0 Typical Performance Characteristics THD+N vs Frequency THD+N vs Frequency 20064763 20064764 THD+N vs Frequency THD+N vs Frequency 20064765 www.national.com 20064766 6 LM4858 Typical Performance Characteristics (Continued) THD+N vs Frequency THD+N vs Frequency 20064767 20064768 THD+N vs Frequency THD+N vs Output Power 20064739 20064740 THD+N vs Output Power THD+N vs Output Power 20064741 20064742 7 www.national.com LM4858 Typical Performance Characteristics (Continued) THD+N vs Output Power THD+N vs Output Power 20064743 20064744 THD+N vs Output Power THD+N vs Output Power 20064745 20064746 THD+N vs Output Power Output Power vs Load Resistance 20064748 20064747 www.national.com 8 LM4858 Typical Performance Characteristics (Continued) Output Power vs Load Resistance Output Power vs Supply Voltage 20064749 20064769 Output Power vs Supply Voltage Dropout Voltage vs Supply Voltage 20064771 20064772 Power Dissipation vs Output Power Power Dissipation vs Output Power 20064755 20064756 9 www.national.com LM4858 Typical Performance Characteristics (Continued) Power Derating Curve Channel Separation 20064757 20064780 Noise Floor Open Loop Frequency Response 20064759 20064762 Supply Current vs Supply Voltage Power Supply Rejection Ratio 20064761 www.national.com 20064760 10 LM4858 Typical Performance Characteristics (Continued) Power Supply Rejection Ratio 20064774 via diameter should be 0.012in-0.013in with a 1.27mm pitch. Ensure efficient thermal conductivity by plating through the vias. Application Information BRIDGED AND SINGLE-ENDED OPERATION As shown in Figure 1, the LM4858 contains three operational amplifiers (A1-A3). These amplifiers can be configured for SE or BTL modes. In the SE mode, the LM4858 operates as a high current output dual op amp. A1 and A3 are independent amplifiers with an externally configured gain of AV = - RF/RI. The outputs of A1 and A3 are used to drive an external set of headphones plugged into the headphone jack. Amplifier A2 is shut down to a high output impedance state in SE mode. This prevents any current flow into the mono bridge-tied load, thereby muting it. In BTL mode, A3 is shut down to a high impedance state. The audio signal from the RIGHT IN pin is directed to the inverting input of A1. As a result, the LEFT IN and RIGHT IN audio signals, VINL and VINR, are summed together at the input of A1. A2 is then activated with a closed-loop gain of AV = -1 fixed by two internal 20kΩ resistors. The outputs of A1 and A2 are then used to drive the mono bridged-tied load. Best thermal performance is achieved with the largest practical heat sink area. If the heatsink and amplifier share the same PCB layer, a nominal 2.5in2 area is necessary for 5V operation with a 4Ω load. Heatsink areas not placed on the same PCB layer as the LM4858 should be 5in2 (min) for the same supply voltage and load resistance. The last two area recommendations apply for 25˚C ambient temperature. Increase the area to compensate for ambient temperatures above 25˚C. The LM4858’s power de-rating curve in the Typical Performance Characteristics shows the maximum power dissipation versus temperature. An example PCB layout for the LD package is shown in the Demonstration Board Layout section. Further detailed and specific information concerning PCB layout, fabrication, and mounting an LD (LLP) package is available from National Semiconductor’s Package Engineering Group under application note AN1187. BRIDGE CONFIGURATION EXPLANATION When the LM4858 is in BTL mode, the output of amplifier A1 serves as the input to amplifier A2, which results in both amplifiers producing signals identical in magnitude, but out of phase by 180˚. Consequently, the differential gain for the mono channel is: EXPOSED-DAP PACKAGE PCB MOUNTING CONSIDERATION The LM4858’s exposed-DAP (die attach paddle) package (LD) provides a low thermal resistance between the die and the PCB to which the part is mounted and soldered. This allows rapid heat transfer from the die to the surrounding PCB copper traces, ground plane, and surrounding air. The result is a low voltage audio power amplifier that produces 1.7W at ≤ 1% THD+N with a 4Ω load. This high power is achieved through careful consideration of necessary thermal design. Failing to optimize thermal design may compromise the LM4858’s high power performance and activate unwanted, though necessary, thermal shutdown protection. The LD package must have its DAP soldered to a copper pad on the PCB. The DAP’s PCB copper pad is connected to a large plane of continuous unbroken copper. This plane forms a thermal mass, heat sink, and radiation area. Place the heat sink area on either outside plane in the case of a two-sided PCB, or on an inner layer of a board with more than two layers. Connect the DAP copper pad to the inner layer or backside copper heat sink area with 4(2x2) vias. The AVD = VOUT / (VINL + VINR) = 2 x (RF / RI) (1) Driving a load differentially through the BTL OUT- and BTL OUT+ outputs is an amplifier configuration commonly referred to as "bridged mode". Bridged mode operation is different from the classical single-ended amplifier configuration where one side of its load is connected to ground. A bridge amplifier design has a few distinct advantages over the single-ended configuration. It drives a load differentially, which doubles output swing for a specified supply voltage. This produces four times the output power as that produced by a single-ended amplifier under the same conditions. This increase in attainable output power assumes that the amplifier is not current limited or clipped. In order to choose an 11 www.national.com LM4858 Application Information POWER SUPPLY BYPASSING (Continued) amplifier’s closed-loop gain without causing excessive output signal clipping, please refer to the Audio Power Amplifier Design section. A bridge configuration, such as the one used in LM4858, also creates a second advantage over single-ended amplifiers. Since the differential outputs, BTL OUT- and BTL OUT+, are biased at half-supply, no net DC voltage exists across the load. This eliminates the need for the output coupling capacitor that a single supply, single-ended amplifier configuration requires. Eliminating an output coupling capacitor in a single-ended configuration forces the half-supply bias voltage across the load. This increases internal IC power dissipation and may cause permanent loudspeaker damage. As with any power amplifier, proper supply bypassing is critical for low noise performance and high power supply rejection. The capacitor location on both the bypass and power supply pins should be as close to the device as possible. The value of the pin bypass capacitor, CB, directly affects the LM4858’s half-supply voltage stability and PSRR. The stability and supply rejection increase as the bypass capacitor’s value increases Typical applications employ a 5V regulator with a 10µF and a 0.1µF bypass capacitors which aid in supply filtering. This does not eliminate the need for bypassing the supply nodes of the LM4858. The selection of bypass capacitors, especially CB, is thus dependent upon desired PSRR requirements, click and pop performance, system cost, and size constraints. POWER DISSIPATION SHUTDOWN FUNCTION Whether the power amplifier is bridged or single-ended, power dissipation is a major concern when designing the amplifier. Equation 2 states the maximum power dissipation point for a single-ended amplifier operating at a given supply voltage and driving a specified load. In order to reduce power consumption while not in use, the LM4858 features amplifier bias circuitry shutdown. This shutdown function is activated by applying a logic high to the SHUTDOWN pin. The trigger point is 2.0V minimum for a logic high level, and 0.8V maximum for a logic low level. It is best to switch between ground and the supply, VDD, to ensure correct shutdown operation. By switching the SHUTDOWN pin to VDD, the LM4858 supply current draw will be minimized in idle mode. Whereas the device will be disabled with shutdown voltages less than VDD, the idle current may be greater than the typical value of 18µA. In either case, the SHUTDOWN pin should be tied to a fixed voltage to avoid unwanted state changes. PDMAX = (VDD)2 / (2π2 RL): Single-Ended (2) However, a direct consequence of the increased power delivered to the load by a bridge amplifier is an increase in internal power dissipation. Equation 3 states the maximum power dissipation point for a bridge amplifier operating at the same given conditions. PDMAX = 4 x (VDD)2 / (2π2 RL): Bridge Mode In many applications, a microcontroller or microprocessor output is used to control the shutdown circuitry. This provides a quick, smooth shutdown transition. Another solution is to use a single-pole, single-throw switch in conjunction with an external pull-up resistor. When the switch is closed, the SHUTDOWN pin is connected to ground and enables the amplifier. If the switch is open, the external pull-up resistor, RPU2 will disable the LM4858. This scheme guarantees that the SHUTDOWN pin will not float, thus preventing unwanted state changes. (3) The LM4858 is designed to drive either two single-ended loads simultaneously or one mono bridged-tied load. In SE mode, the maximum internal power dissipation is 2 times that of Equation 2. In BTL mode, the maximum internal power dissipation is the result of Equation 3. Even with this substantial increase in power dissipation, the LM4858 does not require heatsinking. The power dissipation from Equation 3 must not be greater than the power dissipation predicted by Equation 4: PDMAX = (TJMAX - TA) / θJA HP-IN FUNCTION The LM4858 features a headphone control pin, HP-IN, that enables the switching between BTL and SE modes. A logiclow to HP-IN activates the BTL mode, while a logic-high activates the SE mode. The trigger point is 2.0V minimum for a logic high level and 0.8V maximum for a logic low level. A microcontroller or microprocessor output should be used to control the headphone sense circuitry. This provides a quick, smooth shutdown transition. Another solution is to use a single-pole, single-throw switch in conjunction with an external pull-up resistor. When the switch is closed, the HP-IN pin is connected to the ground and activates BTL mode. If the switch is open, the external pull-up resistor, RPU1, will activate SE mode. This scheme guarantees that the HP-IN pin will not float, thus preventing unwanted state changes. (4) For the package MUB10A, θJA = 194˚C/W. TJMAX = 150˚C for the LM4858. Depending on the ambient temperature, TA, of the surroundings, Equation 4 can be used to find the maximum internal power dissipation supported by the IC packaging. If the result of Equation 3 is greater than that of Equation 4, then either the supply voltage must be decreased, the load impedance increased, or the ambient temperature reduced. For the typical application of a 5V power supply, and an 8Ω bridged load, the maximum ambient temperature possible without violating the maximum junction temperature is approximately 27˚C for package MUB10A. This assumes the device operates at maximum power dissipation and uses surface mount packaging. Internal power dissipation is a function of output power. If typical operation is not around the maximum power dissipation point, operation at higher ambient temperatures is possible. Refer to the Typical Performance Characteristics curves for power dissipation information for different output power levels. www.national.com PROPER SELECTION OF EXTERNAL COMPONENTS Proper selection of external components in applications using integrated power amplifiers is critical for optimum device and system performance. While the LM4858 is tolerant to a variety of external component combinations, consideration must be given to the external component values that maximize overall system quality. 12 must make sure that the chosen power supply voltage and output load does not violate the conditions explained in the Power Dissipation section. (Continued) The LM4858’s unity-gain stability allows a designer to maximize system performance. The LM4858’s gain should be set no higher than necessary for any given application. A low gain configuration maximizes signal-to-noise performance and minimizes THD+N. However, a low gain configuration also requires large input signals to obtain a given output power. Input signals equal to or greater than 1VRMS are available from sources such as audio codecs. Please refer to the section, Audio Power Amplifier Design, for a more complete explanation of proper gain selection. Once the power dissipation equations have been addressed, the required differential gain can be determined from Equation 7. (7) RF / RI = AVD / 2 Selecting Input and Output Capacitor Values Besides gain, one of the major considerations is the closedloop bandwidth of the amplifier. To a large extent, the bandwidth is dictated by the choice of external components shown in Figure 1. The input coupling capacitor CI and resistor RI form a first order high pass filter that limits low frequency response. CI’s value should be based on the desired frequency response weighed against the following: Large value input and output capacitors are both expensive and space consuming for portable designs. Clearly a certain sized capacitor is needed to couple in low frequencies without severe attenuation. But in many cases the speakers used in portable systems, whether internal or external, have little ability to reproduce signals below 150Hz. Thus, large value input and output capacitors may not increase system performance. From Equation 6, the minimum AVD is 2.83; use AVD = 3. The desired input impedance was 20kΩ, and with an AVD of 3, using Equation 8 results in an allocation of RI = 20kΩ and RF = 30kΩ. The final design step is to set the amplifier’s −3dB frequency bandwidth. To achieve the desired ± 0.25dB pass band magnitude variation limit, the low frequency response must extend to at least one−fifth the lower bandwidth limit and the high frequency response must extend o at least five times the upper bandwidth limit. The variation for both response limits is 0.17dB, well within the ± 0.25dB desired limit. This results in: fL = 100Hz / 5 = 20Hz fH = 20kHz x 5 = 100kHz AUDIO POWER AMPLIFIER DESIGN Design a 1W / 8Ω Bridged Audio Amplifier Given: 1WRMS • Power Output: 8Ω • Load Impedance 1VRMS • Input Level: 20kΩ • Input Impedance: 100Hz - 20kHz ± 0.25dB • Bandwidth: As stated in the External Components section, RI in conjunction with CI create a highpass filter. Find the coupling capacitor’s value using Equation 9. CI ≥ 1 / (2πRIfL) CI ≥ 1 / ( 2π x 20kΩ x 20Hz) = 0.397µF (9) Use a 0.39µF capacitor, the closest standard value. The high frequency pole is determined by the product of the desired high frequency pole, fH, and the differential gain, AVD. With AVD = 3 and fH = 100kHz, the resulting GBWP = 150kHz which is much smaller than the LM4858 GBWP of 10MHz. This difference indicates that a designer can still use the LM4858 at higher differential gains without bandwidth limitations. A designer must first determine the minimum supply voltage needed to obtain the specified output power. By extrapolating from the Output Power vs Supply Voltage graphs in the Typical Performance Characteristics section, the supply rail can be easily found. A second way to determine the minimum supply rail is to calculate the required VOPEAK using Equation 5 and add the dropout voltage. This results in Equation 6, where VODTOP and VODBOT are extrapolated from the Dropout Voltage vs Supply Voltage curve in the Typical Performance Characteristics section. PCB LAYOUT AND SUPPLY REGULATION CONSIDERATIONS FOR DRIVING 3Ω AND 4Ω LOADS Power dissipated by a load is a function of the voltage swing across the load and the load’s impedance. As load impedance decreases, load dissipation becomes increasingly dependant on the interconnect (PCB trace and wire) resistance between the amplifier output pins and the load’s connections. Residual trace resistance causes a voltage drop, which results in power dissipated in the trace and not in the load as desired. For example, 0.1Ω trace resistance reduces the output power dissipated by a 4Ω load from 2.0W to 1.95W. This problem of decreased load dissipation is exacerbated as load impedance decreases. Therefore, to maintain the highest load dissipation and widest output voltage swing, PCB traces that connect the output pins to a load must be as wide as possible. Poor power supply regulation adversely affects maximum output power. A poorly regulated supply’s output voltage (5) VDD ≥ (VOPEAK + (VODTOP + VODBOT)) (8) (6) Using the Output Power vs Supply Voltage graph for an 8Ω load, the minimum supply rail is 4.7V. But since 5V is a standard supply voltage in most applications, it is chosen for the supply rail. Extra supply voltage creates headroom that allows the LM4858 to reproduce peaks in excess of 1W without producing audible distortion. However, the designer 13 www.national.com LM4858 Application Information LM4858 Application Information plies, trace resistance creates the same effects as poor supply regulation. Therefore, making the power supply traces as wide as possible helps maintain full output voltage swing. (Continued) decreases with increasing load current. Reduced supply voltage causes decreased headroom, output signal clipping, and reduced output power. Even with tightly regulated sup- Demonstration Board Layout 200647B2 FIGURE 2. Recommended MM PC Board Layout: Component-Side SilkScreen 200647B3 FIGURE 3. Recommended MM PC Board Layout: Component-Side Layout www.national.com 14 LM4858 Demonstration Board Layout (Continued) 200647B4 FIGURE 4. Recommended MM PC Board Layout: Bottom-Side Layout 15 www.national.com LM4858 Physical Dimensions inches (millimeters) unless otherwise noted 10-Lead Mini SOIC, 118 Mil Wide, .5mm Pitch PKG Order Number LM4858MM NS Package Number MUB10A www.national.com 16 LM4858 Mono 1.5 W / Stereo 300mW Power Amplifier Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 14-Lead LLP, 118 Mil Wide, .8mm Pitch PKG Order Number LM4858LD NS Package Number LDA14A LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Americas Customer Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Support Center Email: [email protected] National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: [email protected] Tel: 81-3-5639-7560 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.