HITTITE HMC1055LP2CE

HMC1055LP2CE
V00.0912
Typical Applications
Features
The HMC1055LP2CE is ideal for:
Failsafe Operation - “On” When Unpowered
• RFID & Electronic Toll Collection (ETC)
Wide Vdd Range: 1.2V to 5V
• Tags, Handsets & Portables
Very Low On State Current: 200 nA
• ISM, WLAN, WiMAX & WiBro
Low Insertion Loss: 0.7 dB
• Automotive Telematics
High IP3: +52 dBm
• Test Equipment
Compact SOT26 SMT Package
General Description
Switches - SPST - SMT
Functional Diagram
The HMC1055LP2CE is low-cost SPST Failsafe
switch in 2x2mm,8 lead DFN plastic package for
use in switching application which require low
insertion loss and very low current consumption.
With 0.7 dB typical loss, these devices can control
signals from DC to 4 GHz and are especially suited
for IF and RF applications including RFID, ISM,
automotive and battery powered tags and portables.
RF1 and is reflective open while RF2 is terminated in
50 OHMs when “Off”. The switch requires a minimal
amount of DC current in the “On” state, and offers
compatibility with CMOS and some TTL logic families.
The failsafe topology results in the switch being
normally “On”, i.e. low insertion loss from RF1 to RF2,
when no DC bias is applied.
Electrical Specifications
TA = +25° C, Vdd = +3.3 Vdc, Vctl = 0/+3.3 Vdc (Unless Otherwise Stated), 50 Ohm System
Parameter
Frequency
Min.
Typ.
Max.
Units
Insertion Loss
DC - 3.0 GHz
DC- 4.0 GHz
0.6
1.8
dB
Isolation
DC - 2.0 GHz
DC - 4.0 GHz
36
28
dB
dB
Return Loss
DC - 4.0 GHz
25
dB
Input Power for 0.1 dB Compression
Vctl = 0/+3.3V
0.5 - 4.0 GHz
28
dBm
Input Third Order Intercept
(Two-tone Input Power = +15 dBm Each Tone)
Vctl = 0/+3.3V
0.5 - 4.0 GHz
63
dBm
40
50
ns
ns
Switching Characteristics
DC - 4.0 GHz
tRISE, tFALL (10/90% RF)
tON, tOFF (50% CTL to 10/90% RF)
1
GaAs MMIC SPST
FAILSAFE SWITCH, DC - 4 GHz
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC1055CLP2CE
V00.0912
GaAs MMIC SPST
FAILSAFE SWITCH, DC - 4 GHz
Isolation Vctl=3V VDD=3V
Insertion Loss Vctl=3V VDD=3V
0
-10
-1
ISOLATION (dB)
-2
-3
+25C
+85C
-40C
-4
-20
-30
-40
-50
+25C
+85C
-40C
-60
-70
-5
0
1
2
3
4
0
5
1
0
0
-5
-5
+25C
+85C
-40C
-15
-20
-25
-30
4
5
+25C
+85C
-40C
-10
-15
-20
-25
-30
-35
-35
0
1
2
3
4
5
0
1
FREQUENCY (GHz)
2
3
4
5
FREQUENCY (GHz)
Return Loss Vctl=0V RF1
Return Loss Vctl=0V RF2
0
0
-5
RETURN LOSS (dB)
-2
RETURN LOSS (dB)
3
Return Loss Vctl=3V RF2
RETURN LOSS (dB)
RETURN LOSS (dB)
Return Loss Vctl=3V RF1
-10
2
FREQUENCY (GHz)
FREQUENCY (GHz)
-4
-6
-8
+25C
+85C
-40C
-10
-15
-20
-25
+25C
+85C
-40C
-30
-10
Switches - SPST - SMT
INSERTION LOSS (dB)
0
-35
0
1
2
3
FREQUENCY (GHz)
4
5
0
1
2
3
4
5
FREQUENCY (GHz)
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
2
HMC1055LP2CE
v00.0912
GaAs MMIC SPST
FAILSAFE SWITCH, DC - 4 GHz
Input P0.1dB vs. Temperature
Input IP3 vs. Temperature
80
35
+25C
+85C
-40C
30
INPUT P0.1dB (dBm)
INPUT IP3 (dBm)
75
70
65
60
55
1
2
3
15
10
0
0.5
4
FREQUENCY (GHz)
Switches - SPST - SMT
20
+25C
+85C
-40C
5
50
3
25
1
1.5
2
2.5
3
3.5
4
FREQUENCY (GHz)
Operating Conditions
Vdd & Vctl = 0 Vdc to +3 Vdc; Vctl_max = Vdd + 0.2 Vdc; Idd & Ictl = 0.1 µA, Typical
Conditions
Vdd - Vctl ≥ + 1.2 Vdc
-0.2 Vdc < Vdd - Vctl < +0.4 Vdc
RF1 - RF2
OFF
ON
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
v00.0912
HMC1055LP2CE
GaAs MMIC SPST
FAILSAFE SWITCH, DC - 4 GHz
Absolute Maximum Ratings
RF Input Power (Vctl = 0/+3.3V)
+34 dBm
Supply Voltage (Vdd)
+6.0 Vdc
Control Voltage Range (Vctl)
-0.2 to +(Vdd + 0.2) Vdc
Channel Temperature
150 °C
Continuous Pdiss (T= 85 °C)
(derate 6.67 mW/ °C above 85°C)
0.88 W
Thermal Resistance
74 °C/W
Storage Temperature
-65 to +150 °C
Operating Temperature
-40 to +85 °C
ESD Sensitivity (HBM)
Class 1A
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
DC blocks are required at ports RF1 and RF2.
NOTES:
1. PACKAGE BODY MATERIAL: LOW STRESS INJECTION MOLDED PLASTIC SILICA AND SILICON
IMPREGNATED.
2. LEAD AND GROUND PADDLE MATERIAL: COPPER ALLOY.
3. LEAD AND GROUND PADDLE PLATING: 100% MATTE TIN.
4. DIMENSIONS ARE IN INCHES [MILLIMETERS].
5. LEAD SPACING TOLERANCE IS NON-CUMULATIVE.
6. CHARACTERS TO BE HELVETICA MEDIUM, .016 HIGH, OR LASER MARK LOCATED APPROX. AS
SHOWN.
7. PAD BURR LENGTH SHALL BE 0.15mm MAX. PAD BURR HEIGHT SHALL BE 0.05mm MAX.
8. PACKAGE WARP SHALL NOT EXCEED 0.05mm
9. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND.
10. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB LAND PATTE
Package Information
Part Number
Package Body Material
Lead Finish
HMC1055
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL Rating
MSL1
[1]
Switches - SPST - SMT
Outline Drawing
Package Marking
1055
[[1] Max peak reflow temperature of 260 °C
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
4
HMC1055LP2CE
v00.0912
GaAs MMIC SPST
FAILSAFE SWITCH, DC - 4 GHz
Pin Descriptions
Pin Number
Function
Description
1, 4
N/C
2, 3
GND
These pins and the exposed ground paddle must be
connected to RF ground.
5,8
RF1,RF2
These pins are DC coupled and matched to 50 Ohms.
Blocking capacitors are required.
6
Vdd
Supply Voltage
7
Vctl
See truth and control voltage tables.
Interface Schematic
Switches - SPST - SMT
Typical Application Circuit
Note:
1. DC Blocking capacitors are required for each RF port as shown. Capacitor value determines lowest frequency of operation.
5
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
v00.0912
HMC1055LP2CE
GaAs MMIC SPST
FAILSAFE SWITCH, DC - 4 GHz
List of Materials for Evaluation
EVAL01-HMC1055LP2C
Item
Description
J1 - J2
PCB Mount SMA RF Connector
J3 - J4
DC Pin
C1
1,000 pF Capacitor, 0402 Pkg.
C2 - C3
330 pF capacitor, 0402 Pkg.
U1
HMC1055LP2CE SPST Switch
PCB [2]
600-00215-00 Evaluation PCB
[1] Reference this number when ordering complete evaluation PCB
The circuit board used in the final application
should be generated with proper RF circuit design
techniques. Signal lines at the RF port should
have 50 Ohm impedance and the package ground
leads should be connected directly to the ground
plane similar to that shown above. The evaluation circuit board shown above is available from
Hittite Microwave Corporation upon request.
Switches - SPST - SMT
Evaluation PCB
[2] Circuit Board Material: Rogers 4350
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
6