HMC197A / 197AE v02.1210 Typical Applications Features The HMC197A(E) is ideal for: Low Insertion Loss: 0.4 dB • MMDS & WirelessLAN Ultra Small Package: SOT26 • PCMCIA Wireless Cards Input IP3: +45 dBm • Portable Wireless Positive Control: 0/+3V @ 3 µA Functional Diagram General Description The HMC197A(E) is a low-cost SPDT switch in a 6-lead SOT26 plastic package for use in general switching applications which require very low insertion loss and very small size. The device can control signals from DC to 3 GHz and is especially suited for 900 MHz, 1.8 - 2.2 GHz, and 2.4 GHz ISM applications with less than 1 dB loss. The design provides exceptional insertion loss performance, ideal for filter and receiver switching. RF1 and RF2 are reflective shorts when “Off”. The two control voltages require a minimal amount of DC current and offer compatibility with most CMOS & TTL logic families. See HMC221A(E) for same performance in an alternate SOT26 pin-out. Switches - SPDT - SMT 14 Electrical Specifications, TA = +25° C, Vctl = 0/+3 to +8 Vdc, 50 Ohm System Parameter Frequency Min. Typ. Max. Units 0.4 0.45 0.7 0.8 0.7 0.8 0.9 1.1 dB dB dB dB Insertion Loss DC - 1.0 GHz DC - 2.0 GHz DC - 2.5 GHz DC - 3.0 GHz Isolation DC - 1.0 GHz DC - 2.0 GHz DC - 2.5 GHz DC - 3.0 GHz 24 24 18 14 28 28 22 18 dB dB dB dB Return Loss DC - 1.0 GHz DC - 2.0 GHz DC - 2.5 GHz DC - 3.0 GHz 20 16 14 10 30 22 17 13 dB dB dB dB Input Power for 1dB Compression (Vctl = 0/+5V) 0.5 - 1.0 GHz 0.5 - 3.0 GHz 25 23 30 29 dBm dBm Input Third Order Intercept (Vctl = 0/+5V) (Two-tone Input Power = +7 dBm Each Tone) 0.5 - 1.0 GHz 0.5 - 3.0 GHz 40 38 45 43 dBm dBm Switching Characteristics DC - 3.0 GHz 3 10 ns ns tRISE, tFALL (10/90% RF) tON, tOFF (50% CTL to 10/90% RF) 14 - 1 GaAs MMIC SOT26 SPDT Switch, DC - 3 GHz For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC197A / 197AE v02.1210 GaAs MMIC SOT26 SPDT Switch, DC - 3 GHz Insertion Loss Isolation 0 0 -10 ISOLATION (dB) -1 -1.5 -2 -20 -30 -40 -2.5 -50 -3 0 0.5 1 1.5 2 2.5 0 3 0.5 1 1.5 2 2.5 3 FREQUENCY (GHz) FREQUENCY (GHz) Input 0.1 and 1.0 dB Compression vs. Control Voltage Return Loss 14 35 0 1 dB at 1900 MHz P1dB & P0.1dB (dBm) RETURN LOSS (dB) -10 -20 -30 1 dB at 900 MHz 30 25 0.1 dB at 900 MHz 20 0.1 dB at 1900 MHz -40 15 -50 0 0.5 1 1.5 2 2.5 3 3 4 5 Input Third Order Intercept Point vs. Control Voltage 7 8 9 Distortion vs. Control Voltage Control Input 54 Third Order Intercept (dBm) +7 dBm Each Tone (Vdc) 900 MHz 1900 MHz +3 50 49 +5 50 49 +8 51 50 52 IP3 (dBm) 6 CONTROL INPUT (V) FREQUENCY (GHz) 50 Truth Table 48 Switches - SPDT - SMT INSERTION LOSS (dB) -0.5 *Control Input Voltage Tolerances are ± 0.2 Vdc. Control Input* 900 MHz 1900 MHz 46 44 2 3 4 5 6 CONTROL INPUT (V) 7 8 9 Control Current Signal Path State A (Vdc) B (Vdc) Ia (µA) Ib (µA) RF to RF1 RF to RF2 0 +3 -3 3 ON OFF +3 0 3 -3 OFF ON 0 +5 -5 5 ON OFF +5 0 5 -5 OFF ON 0 +8 -32 32 ON OFF +8 0 32 -32 OFF ON For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 14 - 2 HMC197A / 197AE v02.1210 GaAs MMIC SOT26 SPDT Switch, DC - 3 GHz Absolute Maximum Ratings Compression vs. Control Voltage Carrier at 900 MHz Control Input (Vdc) Input Power for 0.1 dB Compression Carrier at 1900 MHz Input Power for 1.0 dB Compression (dBm) (dBm) Input Power for 0.1 dB Compression Input Power for 1.0 dB Compression (dBm) (dBm) +3 21 24 21 24 +5 28 30 27 30 +8 32 34 31 33 Control Voltage Range (A & B) -0.2 to +12 Vdc Storage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C ESD Sensitivity (HBM) Class 1A ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Caution: Do not operate in 1dB compression at power levels above +31 dBm (Vctl = +5 Vdc) and do not “hot switch” power levels greater than +20 dBm (Vctl = +5Vdc). DC blocks are required at ports RFC, RF1 and RF2. Outline Drawing Switches - SPDT - SMT 14 NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 3. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE. 4. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE. 5. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND. Package Information Part Number Package Body Material Lead Finish MSL Rating HMC197A Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 [1] HMC197AE RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 [2] Package Marking [3] 197A XXXX 197AE XXXX [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX 14 - 3 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC197A / 197AE v02.1210 GaAs MMIC SOT26 SPDT Switch, DC - 3 GHz Typical Application Circuit Notes: 1. Set logic gate and switch Vdd = +3V to +5V and use HCT series logic to provide a TTL driver interface. 2. Control inputs A/B can be driven directly with CMOS logic (HC) with Vdd of 5 to 8 Volts applied to the CMOS logic gates. 3. DC Blocking capacitors are required for each RF port as shown. Capacitor value determines lowest frequency of operation. 4.Highest RF signal power capability is achieved with Vdd = +8V and A/B set to 0/+8V. Evaluation Circuit Board Switches - SPDT - SMT 14 List of Materials for Evaluation PCB 101674 [1] Item Description J1 - J3 PCB Mount SMA RF Connector J4 - J6 DC Pin C1 - C3 330 pF Capacitor, 0603 Pkg. U1 HMC197A / HMC197AE SPDT Switch PCB [2] 101658 Evaluation PCB [1] Reference this number when ordering complete evaluation PCB The circuit board used in the final application should be generated with proper RF circuit design techniques. Signal lines at the RF port should have 50 Ohm impedance and the package ground leads and package bottom should be connected directly to the ground plane similar to that shown above. The evaluation circuit board shown above is available from Hittite Microwave Corporation upon request. [2] Circuit Board Material: Rogers 4350 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 14 - 4