HMC221 / 221E v02.0700 GaAs MMIC SOT26 SPDT SWITCH, DC - 3 GHz D E U N I T N O T C C S U I D D O PR Typical Applications Features The HMC221 & HMC221E is ideal for: RoHS-Compliant Product • ISM Applications Low Insertion Loss: 0.4 dB • PCMCIA Wireless Cards Ultra Small Package: SOT26 • Cellular Applications Input IP3: +45 dBm ns g i s De Positive Control: 0/+3V @ 10 uA ew N r fo d e Description d enGeneral m The HMC221 and HMC221E are low-cost SPDT com e switches in a 6-lead SOT26 plastic package for R Not use in general switching applications which require Included in the HMC-DK005 Designer’s Kits Functional Diagram very low insertion loss and very small size. These devices can control signals from DC to 3 GHz and is especially suited for 900 MHz, 1.8 - 2.2 GHz, and 2.4 GHz ISM applications with less than 1 dB loss. The design provides exceptional insertion loss performance, ideal for filter and receiver switching. RF1 and RF2 are reflective shorts when “Off”. The two control voltages require a minimal amount of DC current and offer compatibility with most CMOS & TTL logic families. See HMC197 for same performance in an alternate SOT26 pin-out. The HMC221E is a RoHScompliant product. SWITCHES - SPDT - SMT 14 Electrical Specifi cations, TA = +25° C, Vctl = 0/+3 to +8 Vdc Parameter Min. Typ. Max. Units 0.4 0.45 0.6 0.8 0.7 0.8 0.9 1.1 dB dB dB dB Insertion Loss DC - 1.0 GHz DC - 2.0 GHz DC - 2.5 GHz DC - 3.0 GHz Isolation DC - 1.0 GHz DC - 2.0 GHz DC - 2.5 GHz DC - 3.0 GHz 24 24 21 14 28 28 25 18 dB dB dB dB Return Loss DC - 1.0 GHz DC - 2.0 GHz DC - 2.5 GHz DC - 3.0 GHz 20 17 16 11 23 22 20 15 dB dB dB dB Input Power for 1 dB Compression (Vctl = 0/+5V) 0.5 - 1.0 GHz 0.5 - 3.0 GHz 25 23 30 29 dBm dBm Input Third Order Intercept (Vctl = 0/+5V) (Two-tone Input Power = +7 dBm Each Tone) 0.5 - 1.0 GHz 0.5 - 3.0 GHz 40 38 45 43 dBm dBm Switching Characteristics DC - 3.0 GHz 3 10 ns ns tRISE, tFALL (10/90% RF) tON, tOFF (50% CTL to 10/90% RF) 14 - 1 Frequency For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC221 / 221E v02.0700 GaAs MMIC SOT26 SPDT SWITCH, DC - 3 GHz D E U N I T N O T C C S U I D D O PR Insertion Loss -0.5 -10 ISOLATION (dB) -1 -1.5 -2 -20 ns g i s De -30 ew N r fo d e end m com e R Input 0.1 and 1.0 dB Not Compression vs. Control Voltage -40 -2.5 -50 -3 0 0.5 1 1.5 2 2.5 0 3 0.5 1 Return Loss 2.5 3 -10 -15 -20 -25 -30 14 1 dB at 1900 MHz INPUT POWER FOR 0.1 AND 1 dB COMPRESSION (dBm) -5 ISOLATION (dB) 2 35 0 1 dB at 900 MHz 30 25 0.1 dB at 900 MHz 20 0.1 dB at 1900 MHz 15 -35 0 0.5 1 1.5 2 2.5 3 3 4 5 6 7 8 9 CONTROL INPUT (Vdc) FREQUENCY (GHz) Input Third Order Intercept Point vs. Control Voltage Distortion vs. Control Voltage Control Input 48 INPUT THIRD ORDER INTERCEPT(dBm) 1.5 FREQUENCY (GHz) FREQUENCY (GHz) Third Order Intercept (dBm) +7 dBm Each Tone (Vdc) 900 MHz +3 41 39 +5 45 43 +8 46 44 46 44 1900 MHz Truth Table 42 SWITCHES - SPDT - SMT INSERTION LOSS (dB) Isolation 0 0 *Control Input Voltage Tolerances are ± 0.2 Vdc. Control Input* 900 MHz 1900 MHz 40 38 2 3 4 5 6 CONTROL INPUT (Vdc) 7 8 9 Control Current Signal Path A (Vdc) B (Vdc) Ia (uA) Ib (uA) RF to RF1 RF to RF2 0 +3 -10 10 ON OFF +3 0 10 -10 OFF ON 0 +5 -55 55 ON OFF +5 0 55 -55 OFF ON 0 +7 -210 210 ON OFF +7 0 210 -210 OFF ON 0 +8 -280 280 ON OFF +8 0 280 -280 OFF ON For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 14 - 2 HMC221 / 221E v02.0700 GaAs MMIC SOT26 SPDT SWITCH, DC - 3 GHz D E U N I T N O T C C S U I D D O PR Absolute Maximum Ratings Compression vs. Control Voltage Carrier at 900 MHz Control Input Input Power for 0.1 dB Compression Carrier at 1900 MHz Input Power for 1.0 dB Compression Input Power for 0.1 dB Compression Input Power for 1.0 dB Compression (Vdc) (dBm) (dBm) (dBm) (dBm) +3 17 20 17 20 +5 25 30 24 29 31 33 30 32 Control Voltage Range (A & B) -0.2 to +12 Vdc Storage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C ESD Sensitivity (HBM) Class 1A ew N r fo Caution: Do not operate in 1dB compression at power levels above d e +31 dBm (Vctl = +5 Vdc) and do not “hot switch” power levels d greater than +20 dBm (Vctl = +5Vdc). DC blocks are required aten m ports RFC, RF1 and RF2. com e R Not +8 Outline Drawing SWITCHES - SPDT - SMT 14 ns g i s De ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 3. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE. 4. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE. 5. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND. Package Information Part Number Package Body Material Lead Finish MSL Rating HMC221 Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 HMC221E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 Package Marking [1] H221 [2] 221E [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C 14 - 3 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC221 / 221E v02.0700 GaAs MMIC SOT26 SPDT SWITCH, DC - 3 GHz D E U N I T N O T C C S U I D D O PR Typical Application Circuit Notes: 1. Set logic gate and switch Vdd = +3V to +5V and use HCT series logic to provide a TTL driver interface. 2. Control inputs A/B can be driven directly with CMOS logic (HC) with Vdd of 5 to 8 Volts applied to the CMOS logic gates. ew N r fo 4. Highest RF signal power capability is achieved with Vdd = +8V d e and A/B set to 0/+8V. end m com e R Not 3. DC Blocking capacitors are required for each RF port as shown. Capacitor value determines lowest frequency of operation. ns g i s De 14 SWITCHES - SPDT - SMT Evaluation Circuit Board List of Materials for Evaluation PCB 101675 [1] Item Description J1 - J3 PCB Mount SMA RF Connector J4 - J7 DC Pin C1 - C3 330 pF capacitor, 0402 Pkg. U1 HMC221 / HMC221E SPDT Switch PCB [2] 101659 Evaluation PCB [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 The circuit board used in the final application should be generated with proper RF circuit design techniques. Signal lines at the RF port should have 50 Ohm impedance and the package ground leads and package bottom should be connected directly to the ground plane similar to that shown above. The evaluation circuit board shown above is available from Hittite Microwave Corporation upon request. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 14 - 4