GL34A-GL34M Surface Mount Rectifiers REVERSE VOLTAGE: 50 - 1000 V CURRENT: 0.5A Features 11 DO - 213AA Plastic package has underwriters laboratory 1 flammability classifications For surface mounted applications SOLDERABLE ENDS Low profile package 0 D2=D1 + -0.20 1.6± 0.1 Built-in strain relief,ideal for automated placement Glass passivated chip junction 11 D2 D1 High temperature soldering: 1 250oC/10 seconds at terminals 0.5± 0.1 0.5± 0.1 Mechanical Data 11 3.5± 0.2 Case:JEDEC DO-213AA,molded plastic over 11passivated chip Dimensions in millimeters Polarity: Color band denotes cathode end Weight: 0.0014 ounces, 0.036 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25oC ambient temperature unless otherwise specified GL34A GL34B GL34D GL34G GL34J GL34K GL34M UNITS Polarity color bands (2nd Band) Gray Red Orange Yellow Green Blue Violet Maximum recurrent peak reverse voltage VRRM 50 100 200 400 600 800 1000 V Maximum RMS voltage VRWS 35 70 140 280 420 560 700 V Maximum DC blocking voltage VDC 50 100 200 400 600 800 1000 V Maximum average forw ord rectified current V @TL=75 Peak forw ard surge current V 8.3ms single half-sine-w ave superimposed V on rated load (JEDEC Method) Maximum instantaneous forw ard voltage at 0.5 A Maximum DC reverse current at rated DC blockjing voltage @TA=25oC IF(AV) 0.5 A IFSM 10.0 A VF IR @TA=125oC 1.2 1.3 5.0 A 50.0 Typical junction capacitance(NOTE 2) CJ 4.0 Typical reverse recovery time(NOTE3) t rr 1.5 Typical thermal resitance (NOTE 4) Operating junction temperature range Storage temperature range V R JA TJ TSTG 150 -55--------+150 -55--------+150 NOTE: 1.Measured at 1.0MHz and applied reverse voltage of 4.0volts 2.Thermal resistance form junction to ambient and junction to lead P.C.B mounted on 0.27"X0.27"(7.0X7.0mm2) copper pad areas 3.Measured with IF=0.5A,IR=1.0A,Irr=0.25A. 4. Thermal resistance from junction to ambient and junction to lead P.C.B.mounted on 0.27''X0.27''(7.0X7.0mm2) copper pad areas http://www.luguang.cn mail:[email protected] pF S o C/W o C GL34A-GL34M Surface Mount Rectifiers Ratings AND Charactieristic Curves FIG.1 -- FORWARD DERATING CURVE FIG.2 PEAK FORWARD SURGE CURRENT 100 Resistive or inductive Load 1.0 0.8 0.6 0.4 0.2X0.2(5.0X5.0mm) THICK COPPERPAND AREAS 0.2 0 0 20 40 60 80 100 120 140 160 PEAK FORWARD SURGE CURRENT,AMPERES AVERAGE FORWARD CURRENT,AMPERES 1.2 O T L =110 C 8.3m s Single Half Sine (JE DE C M ethod) 40 30 S 1(A-J) 10 S 1(K,M) 1 1 10 AMBIENT TEMPERATURE 10 O TJ=25 C 1 0.01 0.4 0.6 0.8 1.0. 1.2 S 1.4 1.6 1.8 FIG.4 -- TYPICAL REVERSE CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT MICROAMPERES INSTANTANEOUS FORWARD CURRENT,AMPERES 100 Puise Width=300 1%DUTY CYCLE 100 NUMBER OF CYCLES AT 60Hz FIG.3 -- TYPICAL FORWARD CHARACTERISTICS 0.1 W ave 2.0 INSTANTANEOUS FORWARD VOLTAGE,VOLTS 100 10 O TJ=125 C 1 O TJ=75 C 0.1 TJ=25OC 0.01 0.001 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, FIG.5-TYPICAL JUNCTION CAPACITANCE FIG.6-TRANSIENT THERMAL IMPEDANCE 100 60 f=1MHz TJ=25 40 20 10 4 2 1 .1 .2 .4 1.0 2 4 10 20 40 REVERSE VOLTAGE,VOLTS http://www.luguang.cn 100 TRANSIENT THERMAL IMPEDANCE, /W JUNCTION CAPACITANCE pF 100 10 S1(K,M) S1(A-J) 1 UNITS MOUNTED on 0.20x0.20''(5.0X5.0mm)X0.5mil INCHES(0.013mm) THICK COPPERLAND AREAS 0.1 0.01 0.1 1 10 PULSE DURATON,SEC mail:[email protected] 100