No. STSE-CM6036A <Cat.No.060410> SPECIFICATIONS FOR NICHIA CHIP TYPE FULL COLOR MODEL : NSSM065T NICHIA CORPORATION -0- LED Nichia STSE-CM6036A <Cat.No.060410> 1.SPECIFICATIONS (1) Absolute Maximum Ratings Item Symbol Forward Current Pulse Forward Current ½ Reverse Voltage Power Dissipation ½½ Total Power Dissipation ½½½ Operating Temperature Storage Temperature Soldering Temperature IF IFP VR PD Ptot Topr Tstg Tsld ½ ½½ (Ta=25°C) Unit Absolute Maximum Rating Blue Green Red 35 35 50 110 110 200 5 123 123 125 160 -30 ~ + 85 -40 ~ +100 Reflow Soldering : 260°C for 10sec. Hand Soldering : 350°C for 3sec. mA mA V mW mW °C °C IFP Conditions : Pulse Width < = 10msec. and Duty < = 1/10 Value for one LED device (Single color). ½½½ Value for total power dissipation when two and more devices are lit simultaneously. (2) Initial Electrical/Optical Characteristics Item (Ta=25°C) Symbol Green Red Unit Typ. Max. Typ. Max. Typ. Max. IF=20[mA] (3.2) 3.5 (3.2) 3.5 (2.1) 2.5 VR= 5[V] - 50 - 50 - 50 IF=20[mA] (400) - (1200) - (700) - V µA mcd x - IF=20[mA] 0.133 - 0.189 - 0.700 - - y - IF=20[mA] 0.075 - 0.718 - 0.299 - - Reverse Current Luminous Intensity ½ Blue VF IR Iv Forward Voltage Chromaticity Coordinate Condition ½ Please refer to CIE 1931 chromaticity diagram. (3) Ranking (Ta=25°C) Item Symbol Iv Luminous Intensity Condition Blue IF=20[mA] Max. Min. Max. Min. Max. 250 500 800 1600 380 1080 (IF=20mA, Ta=25°C) Blue x y 0.139 0.035 0.129 0.050 Rank W 0.113 0.134 0.080 0.105 0.145 0.072 0.152 0.056 0.136 0.739 Rank G0d 0.176 0.220 0.750 0.745 0.250 0.638 0.219 0.637 Green x y 0.190 0.628 -1- Red Min. ½ Luminous Intensity Measurement allowance is ± 10%. Color Ranks Green Unit mcd Nichia STSE-CM6036A <Cat.No.060410> Red x y 0.674 0.296 Rank R 0.648 0.677 0.323 0.323 0.708 0.292 Color Coordinates Measurement allowance is ± 0.01. 2.INITIAL OPTICAL/ELECTRICAL CHARACTERISTICS Please refer to figure’s page. 3.OUTLINE DIMENSIONS AND MATERIALS Please refer to figure’s page. Package Material as follows ; Encapsulating Resin Electrodes : : : Heat-Resistant Polymer Epoxy Resin (Diffused) Ag Plating Copper Alloy 4.PACKAGING · The LEDs are packed in cardboard boxes after taping. Please refer to figure’s page. The label on the minimum packing unit shows ; Part Number, Lot Number, Quantity · In order to protect the LEDs from mechanical shock, we pack them in cardboard boxes for transportation. · The LEDs may be damaged if the boxes are dropped or receive a strong impact against them, so precautions must be taken to prevent any damage. · The boxes are not water resistant and therefore must be kept away from water and moisture. · When the LEDs are transported, we recommend that you use the same packing method as Nichia. 5.LOT NUMBER The first six digits number shows lot number. The lot number is composed of the following characters; - Year ( 5 for 2005, 6 for 2006 ) Month ( 1 for Jan., 9 for Sep., A for Oct., Nichia's Product Number -2- B for Nov. ) Nichia STSE-CM6036A <Cat.No.060410> 6.RELIABILITY (1) TEST ITEMS AND RESULTS Test Item Standard Test Method Test Conditions Note Number of Damaged 2 times 0/50 Resistance to Soldering Heat (Reflow Soldering) JEITA ED-4701 300 301 Tsld=260°C, 10sec. (Pre treatment 30°C,70%,168hrs.) Thermal Shock JEITA ED-4701 300 307 0°C ~ 100°C 15sec. 15sec. 100 cycles 0/50 Temperature Cycle JEITA ED-4701 100 105 -40°C ~ 25°C ~ 100°C ~ 25°C 30min. 5min. 30min. 5min. 100 cycles 0/50 Moisture Resistance Cyclic JEITA ED-4701 200 203 25°C ~ 65°C ~ -10°C 90%RH 24hrs./1cycle 10 cycles 0/50 High Temperature Storage JEITA ED-4701 200 201 Ta=100°C 500hrs. 0/50 Temperature Humidity Storage JEITA ED-4701 100 103 Ta=60°C, RH=90% 500hrs. 0/50 Low Temperature Storage JEITA ED-4701 200 202 Ta=-40°C 500hrs. 0/50 B IF=9mA G IF=19mA R IF=15mA 500hrs. 0/50 B IF=5mA G,R IF=11mA 500hrs. 0/50 B IF=9mA G IF=19mA R IF=15mA 500hrs. 0/50 Steady State Operating Life Ta=25°C, Steady State Operating Life of High Humidity Heat 60°C, RH=90%, Steady State Operating Life of Low Temperature Ta=-30°C, Value for one LED device (Single color). (2) CRITERIA FOR JUDGING DAMAGE (Value for one LED device (Single color).) Criteria for Judgement Min. Max. Item Symbol Test Conditions Forward Voltage VF B,G,R IF=20mA - U.S.L.*) 1.1 Reverse Current IR B,G,R VR=5V - U.S.L.*) 2.0 Luminous Intensity IV B,G,R IF=20mA L.S.L.**) 0.7 - *) U.S.L. : Upper Standard Level **) L.S.L. : Lower Standard Level -3- Nichia STSE-CM6036A-1 <Cat.No.070119> 7.CAUTIONS (1) Moisture Proof Package · When moisture is absorbed into the SMT package it may vaporize and expand during soldering. There is a possibility that this can cause exfoliation of the contacts and damage to the optical characteristics of the LEDs. For this reason, the moisture proof package is used to keep moisture to a minimum in the package. · The moisture proof package is made of an aluminum moisture proof bag. A package of a moisture absorbent material (silica gel) is inserted into the aluminum moisture proof bag. The silica gel changes its color from blue to pink as it absorbs moisture. (2) Storage · Storage Conditions Before opening the package : The LEDs should be kept at 30°C or less and 90%RH or less. The LEDs should be used within a year. When storing the LEDs, moisture proof packaging with absorbent material (silica gel) is recommended. After opening the package : The LEDs should be kept at 30°C or less and 70%RH or less. The LEDs should be soldered within 168 hours (7days) after opening the package. If unused LEDs remain, they should be stored in moisture proof packages, such as sealed containers with packages of moisture absorbent material (silica gel). It is also recommended to return the LEDs to the original moisture proof bag and to reseal the moisture proof bag again. · If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : more than 24 hours at 65 ± 5°C · Nichia LED electrodes are silver plated copper alloy. The silver surface may be affected by environments which contain corrosive substances. Please avoid conditions which may cause the LED to corrode, tarnish or discolor. This corrosion or discoloration may cause difficulty during soldering operations. It is recommended that the User use the LEDs as soon as possible. · Please avoid rapid transitions in ambient temperature, especially in high humidity environments where condensation can occur. (3) Heat Generation · Thermal design of the end product is of paramount importance. Please consider the heat generation of the LED when making the system design. The coefficient of temperature increase per input electric power is affected by the thermal resistance of the circuit board and density of LED placement on the board, as well as other components. It is necessary to avoid intense heat generation and operate within the maximum ratings given in this specification. · During operation of the LEDs the total power dissipation of the diode elements (red, green, and blue) within the LEDs must not exceed the maximum power dissipation. · The operating current should be decided after considering the ambient maximum temperature of LEDs. -4- Nichia STSE-CM6036A-1 <Cat.No.070119> (4) Soldering Conditions · The LEDs can be soldered in place using the reflow soldering method. Nichia cannot make a guarantee on the LEDs after they have been assembled using the dip soldering method. · Recommended soldering conditions Pre-heat Pre-heat time Peak temperature Soldering time Condition Reflow Soldering Lead Solder Lead-free Solder 180 ~ 200°C 120 ~ 150°C 120 sec. Max. 120 sec. Max. 240°C Max. 260°C Max. Hand Soldering Temperature Soldering time 350°C Max. 3 sec. Max. (one time only) 10 sec. Max. 10 sec. Max. refer to refer to Temperature - profile 1. Temperature - profile 2. (N2 reflow is recommended.) Although the recommended soldering conditions are specified in the above table, reflow or hand soldering at the lowest possible temperature is desirable for the LEDs. A rapid-rate process is not recommended for cooling the LEDs down from the peak temperature. [Temperature-profile (Surface of circuit board)] Use the conditions shown to the under figure. <1 : Lead Solder> <2 : Lead-free Solder> 2.5 ~ 5°C / sec. Pre-heating 120 ~ 150°C 60sec.Max. Above 200°C 2.5 ~ 5°C / sec. 1 ~ 5°C / sec. 240°C Max. 10sec. Max. 1 ~ 5°C / sec. Pre-heating 180 ~ 200°C 60sec.Max. 260°C Max. 10sec. Max. Above 220°C 120sec.Max. 120sec.Max. Use the following conditions shown in the figure. 3.05 0.85 0.75 0.85 [Recommended soldering pad design] 1.55 1.4 1.55 (Unit : mm) 4.5 · Occasionally there is a brightness decrease caused by the influence of heat or ambient atmosphere during air reflow. It is recommended that the User use the nitrogen reflow method. · Repairing should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used. It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. · Reflow soldering should not be done more than two times. · When soldering, do not put stress on the LEDs during heating. · After soldering, do not warp the circuit board. (5) Cleaning · It is recommended that isopropyl alcohol be used as a solvent for cleaning the LEDs. When using other solvents, it should be confirmed beforehand whether the solvents will dissolve the package and the resin or not. Freon solvents should not be used to clean the LEDs because of worldwide regulations. · Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of ultrasonic cleaning on the LEDs depends on factors such as ultrasonic power and the assembled condition. Before cleaning, a pre-test should be done to confirm whether any damage to the LEDs will occur. -5- Nichia STSE-CM6036A-1 <Cat.No.070119> (6) Static Electricity · Static electricity or surge voltage damages the Blue/Green LEDs. It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs. · All devices, equipment and machinery must be properly grounded. It is recommended that precautions be taken against surge voltage to the equipment that mounts the LEDs. · When inspecting the final products in which LEDs were assembled, it is recommended to check whether the assembled LEDs are damaged by static electricity or not. It is easy to find static-damaged LEDs by a light-on test or a VF test at a lower current (below 1mA is recommended). · Damaged LEDs will show some unusual characteristics such as the leak current remarkably increases, the forward voltage becomes lower, or the LEDs do not light at the low current. Criteria : (VF > 2.0V at IF=0.5mA) (7) Others · NSSM065 complies with RoHS Directive. · Care must be taken to ensure that the reverse voltage will not exceed the absolute maximum rating when using the LEDs with matrix drive. · The LED light output is strong enough to injure human eyes. Precautions must be taken to prevent looking directly at the LEDs with unaided eyes for more than a few seconds. · Flashing lights have been known to cause discomfort in people; you can prevent this by taking precautions during use. Also, people should be cautious when using equipment that has had LEDs incorporated into it. · The LEDs described in this brochure are intended to be used for ordinary electronic equipment (such as office equipment, communications equipment, measurement instruments and household appliances). Consult Nichia’s sales staff in advance for information on the applications in which exceptional quality and reliability are required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or health (such as for airplanes, aerospace, submersible repeaters, nuclear reactor control systems, automobiles, traffic control equipment, life support systems and safety devices). · User shall not reverse engineer by disassembling or analysis of the LEDs without having prior written consent from Nichia. When defective LEDs are found, the User shall inform Nichia directly before disassembling or analysis. · The formal specifications must be exchanged and signed by both parties before large volume purchase begins. · The appearance and specifications of the product may be modified for improvement without notice. -6- Nichia STSE-CM6036A <Cat.No.060410> ICI Chromaticity Diagram 0.9 520 530 0.8 540 510 0.7 G0d 550 560 0.6 570 500 0.5 580 y 590 0.4 600 610 0.3 490 R 620 630 0.2 480 0.1 W 470 460 0 0 0.1 0.2 0.3 0.4 x ½ Color Coordinates Measurement allowance is ± 0.01. -7- 0.5 0.6 0.7 0.8 20 10 5 BLUE GREEN RED 1 1.6 2.0 2.4 2.8 3.2 3.6 4.0 4.4 4.8 Forward Voltage VF (V) 3.6 3.2 2.8 2.4 2.0 1.6 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (°C) 1 2.0 Relative Luminosity (a.u.) Forward Voltage VF (V) -8- 4.0 2 0 20 40 60 80 100 120 Forward Current IFP (mA) Ambient Temperature vs. Relative Luminosity (IFP=20mA) BLUE GREEN RED 3 0 Ambient Temperature vs. Forward Voltage 4.4 4 1.0 0.5 0.2 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (°C) 200 110 50 35 BLUE, GREEN RED 20 10 1 5 10 20 50 100 Duty Ratio (%) Ambient Temperature vs. Power Dissipation ½ (IFP=20mA) BLUE GREEN RED (Ta=25°C) 300 Ambient Temperature vs. Power Dissipation ½½ 140 BLUE, GREEN RED 120 100 80 60 40 20 0 0 20 40 60 80 100 Ambient Temperature Ta (°C) 200 160 120 80 40 0 0 20 40 60 80 100 Ambient Temperature Ta (°C) (NOTE) ½ Model NICHIA CORPORATION NSSM065 Title CHARACTERISTICS No. 060323650591 Nichia STSE-CM6036A <Cat.No.060410> The value for one device should be within the absolute maximum rating when one or two and more devices are lit (Full color). ½½ Total value should be within the absolute maximum rating when two and more devices are lit (Full color). Total Power Dissipation Ptot (mW) 50 BLUE GREEN RED 5 Power Dissipation PD (mW) 100 (Ta=25°C) 6 Allowable Forward Current IFP (mA) (Ta=25°C) Relative Luminosity (a.u.) Forward Current IFP (mA) 200 Duty Ratio vs. Allowable Forward Current Forward Current vs. Relative Luminosity Forward Voltage vs. Forward Current Spectrum Directivity BLUE GREEN RED 0.8 0.6 0.4 0.2 -9- 0 400 450 500 550 600 650 700 Wavelength λ (nm) 1.0 (Ta=25°C, IFP=20mA) 0.5 BLUE GREEN RED 0 -90° -60° -30° 0° 30° 60° 90° Radiation Angle (Ta=25°C, IFP=20mA) 1.0 Relative Luminosity (a.u.) 1.0 (Ta=25°C, IF=20mA) Relative Luminosity (a.u.) Relative Emission Intensity (a.u.) 1.2 Y(90°) Y-Y X-X X (-90°) X (90°) Y(-90°) 0.5 BLUE GREEN RED 0 -90° -60° -30° 0° 30° 60° 90° Radiation Angle NICHIA CORPORATION NSSM065 Title CHARACTERISTICS No. 070315650602 Nichia STSE-CM6036A-2 <Cat.No.070326> Model 3.3 3 (R 0.7) 4 3 5 2 6 1 2.1 (2.6) 3 0.5 (2.6) -10- (C 0.3 ) 1 Pin Mark (0.3) 4 1.5 (0.9) 5 Green Blue ITEM 2 1 MATERIALS PACKAGE Heat-Resistant Polymer ENCAPSULATING RESIN Epoxy Resin (Diffused) ELECTRODES Ag Plating Copper Alloy (1.24) Model Red LED die and blue LED die are mounted on the cathode side, green LED die is mounted on the anode side. NICHIA CORPORATION Title No. NSSM065 OUTLINE DIMENSIONS 060314650611 Unit mm 15/1 Scale Allow ±0.2 Nichia STSE-CM6036A <Cat.No.060410> 0.8 6 Red 3 1 Pin Mark 4±0.1 Reel end of tape φ 1+0.25 -0 1.65±0.1 11.4±1 9±0.3 φ 60+1 -0 φ2 1 ±0.8 ±0.2 φ 13 Label 3in1 LED TYPE NSSM065T LOT xxxxxx QTY pcs 3.1±0.1 No LEDs φ 180+0 -3 Reel part 3.45±0.1 (2.75) 3.5±0.05 2±0.05 0.2±0.05 8+0.3 - 0.1 4±0.1 φ 1.5+0.1 -0 1.75±0.1 Taping part LEDs mounting part No LEDs -11Top cover tape Pull direction Embossed carrier tape Reel Lead Min.160mm (No LEDs) Reel Lead Min.100mm (No LEDs) Reel Lead Min.400mm Model Taping is based on the JIS C 0806 : Packaging of Electronic Components on Continuous Tapes. NICHIA CORPORATION Title No. NSSM065T TAPING DIMENSIONS 060314650621 Unit mm Scale Allow Nichia STSE-CM6036A <Cat.No.060410> 2,500pcs/Reel Nichia STSE-CM6036A <Cat.No.060410> The reel and moisture absorbent material are put in the moisture proof foil bag and then heat sealed. Reel Label NICHIA Seal 3in1 LED TYPE LOT QTY NSSM065T xxxxxx PCS NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN Moisture proof foil bag Moisture absorbent material The box is partitioned with the cardboard. Label NICHIA 3in1 LED Nichia LED TYPE NSSM065T QTY PCS NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN Packing unit Moisture proof foil bag Cardboard box Cardboard box S Cardboard box M Cardboard box L Reel/bag 1reel Quantity/bag (pcs) 2,500 MAX. Dimensions (mm) 291¯237¯120¯8t 259¯247¯243¯5t 444¯262¯259¯8t NICHIA CORPORATION -12- Reel/box 7reel MAX. 15reel MAX. 30reel MAX. Quantity/box (pcs) 17,500 MAX. 37,500 MAX. 75,000 MAX. Model NSSM065T Title PACKING No. 060314650631