DA6180C.000 26 November, 2010 MAS6180C AM Receiver IC This is preliminary information on a new product under development. Micro Analog Systems Oy reserves the right to make any changes without notice. • • • • • • • • Single Band Receiver IC High Sensitivity Very Low Power Consumption Wide Supply Voltage Range Power Down Control Control for AGC On High Selectivity by Crystal Filter Fast Startup Feature DESCRIPTION The MAS6180 AM-Receiver chip is a highly sensitive, simple to use AM receiver specially intended to receive time signals in the frequency range from 40 kHz to 100 kHz. Only a few external components are required for time signal receiver. The circuit has preamplifier, wide range automatic gain control, demodulator and output FEATURES • • • • • • • • • • • comparator built in. The output signal can be processed directly by an additional digital circuitry to extract the data from the received signal. The control for AGC (automatic gain control) can be used to switch AGC on or off if necessary. APPLICATIONS Single Band Receiver IC Highly Sensitive AM Receiver, 0.4 µVRMS typ. Wide Supply Voltage Range from 1.5 V to 5.5 V Very Low Power Consumption Power Down Control Fast Startup Only a Few External Components Necessary Control for AGC On Wide Frequency Range from 40 kHz to 100 kHz High Selectivity by Quartz Crystal Filter Differential Input • Single Band Time Signal Receiver WWVB (USA), JJY (Japan), DCF77 (Germany), MSF (UK), HGB (Switzerland) and BPC (China) BLOCK DIAGRAM VDD QOP VDD AGC Amplifier QI AON QOM RFIP RFIM Demodulator & Comparator OUT Power Supply/Biasing VDD VSS PDN AGC DEC 1 (13) DA6180C.000 26 November, 2010 MAS6180 PAD LAYOUT 1160 µm VDD VSS MAS6180Cx RFIP QI PDN AGC AON OUT DEC 1320 µm RFIM QOP QOM VSS pad bonded first! DIE size = 1160 µm x 1320 µm; PAD size = 80 µm x 80 µm Note: Because the substrate of the die is internally connected to VSS, the die has to be connected to VSS or left floating. Please make sure that VSS is the first pad to be bonded. Pick-and-place and all component assembly are recommended to be performed in ESD protected area. Note: Coordinates are pad center points where origin has been located in bottom-left corner of the silicon die. Pad Identification Name X-coordinate Y-coordinate Power Supply Voltage Positive Quartz Filter Output Negative Quartz Filter Output Quartz Filter Input for Crystal AGC Capacitor Receiver Output Demodulator Capacitor AGC On Control Power Down Positive Receiver Input Negative Receiver Input Power Supply Ground VDD QOP QOM QI AGC OUT DEC AON PDN RFIP RFIM VSS 126 µm 126 µm 126 µm 126 µm 126 µm 126 µm 1034 µm 1034 µm 1034 µm 1034 µm 1034 µm 1034 µm 1122 µm 955 µm 787 µm 604 µm 435 µm 258 µm 261 µm 445 µm 613 µm 802 µm 980 µm 1111 µm Note 1 2 3 4 5 5 Notes: 1) QOM bonding pad is electrically unconnected in MAS6180C1 version 2) OUT = VSS when carrier amplitude at maximum; OUT = VDD when carrier amplitude is reduced (modulated) - the output is a current source/sink with |IOUT| > 5 µA - at power down the output is pulled to VSS (pull down switch) 3) AON = VSS means AGC off (hold current gain level); AON = VDD means AGC on (working) - Internal pull-up with current < 1 µA which is switched off at power down 4) PDN = VSS means receiver on; PDN = VDD means receiver off Fast start-up is triggered when the receiver is after power down (PDN=VDD) controlled to power up (PDN=VSS) i.e. at the falling edge of PDN signal. 5) Receiver inputs RFIP and RFIM have both 1.4 MΩ biasing resistors towards VDD 2 (13) DA6180C.000 26 November, 2010 6) ABSOLUTE MAXIMUM RATINGS All Voltages with Respect to Ground Parameter Supply Voltage Input Voltage ESD Rating Symbol VDD-VSS VIN VESD Latchup Current Limit Operating Temperature Storage Temperature ILUT TOP TST Conditions For all pins, Human Body Model (HBM) For all pins Min Max Unit - 0.3 VSS-0.3 ±2 +5.5 VDD+0.3 V V kV ±100 -40 - 55 +85 +150 mA °C °C Stresses beyond those listed may cause permanent damage to the device. The device may not operate under these conditions, but it will not be destroyed. Note: In latchup testing the supply voltages are connected normally to the tested device. Then pulsed test current is fed to each input separately and device current consumption is observed. If the device current consumption increases suddenly due to test current pulses and the abnormally high current consumption continues after test current pulses are cut off then the device has gone to latch up. Current pulse is turned on for 10 ms and off for 20 ms. ELECTRICAL CHARACTERISTICS Operating Conditions: VDD = 5.0V, Temperature = 25°C, unless otherwise specified. Parameter Operating Voltage Current Consumption Stand-By Current Input Frequency Range Minimum Input Voltage Maximum Input Voltage Receiver Input Resistance Receiver Input Capacitance Input Levels |lIN|<0.5 µA Output Current VOL<0.2 VDD;VOH >0.8 VDD DCF77 Output Pulses Symbol Conditions Min Typ Max Unit VDD IDD TA = -40°C..+85°C 1.5 5.0 66 68 43 45 5.5 80 V µA 65 µA 0.1 100 1 µA kHz IDDoff fIN VIN min VIN max RRFI CRFI VIL VIH |IOUT| Startup Time T 100ms T 200ms T 100ms T 200ms T 500ms T 200ms T 500ms T 800ms T 200ms T 500ms T 800ms T 200ms T 500ms T 800ms TStart Output Delay Time TDelay MSF Output Pulses WWVB Output Pulses JJY60 Output Pulses JJY40 Output Pulses VDD=1.5 V, Vin=0.4 µVrms VDD=5 V, Vin=0.4 µVrms VDD=1.5 V, Vin=20 mVrms VDD=5 V, Vin=20 mVrms See note below. 40 0.4 20 Differential Input, f=77.5 kHz 600 1.1 0.35 VDD-0.35 5 1 µVrms ≤ VIN ≤ 20 mVrms, see note below! 1 µVrms ≤ VIN ≤ 20 mVrms, see note below! 1 µVrms ≤ VIN ≤ 20 mVrms, see note below! 1 µVrms ≤ VIN ≤ 20 mVrms, see note below! 1 µVrms ≤ VIN ≤ 20 mVrms, see note below! Fast Start-up, Vin=0.4 µVrms Fast Start-up, Vin=20 mVrms µVrms mVrms kΩ pF V 15 µA 95 195 120 220 520 200 500 800 210 505 800 200 495 790 1.3 3.5 50 ms ms ms ms ms 4 s 100 ms Note: Stand-by current consumption may increase if V IH and V IL differ from VDD and 0 respectively. Note: See Note 6: Time Signal Software’s Pulse Width Recognition Limits and Table 5 on page 7! 3 (13) DA6180C.000 26 November, 2010 TYPICAL APPLICATION Note 1 Note 4 Optional Control for AGC on/hold MAS6180C1 VDD QOP Note 5 QI RFIP VDD Ferrite Antenna AON QOM AGC Amplifier RFIM Demodulator & Comparator OUT Receiver Output Power Supply/Biasing VDD VSS PDN Note 3 Power Down / Fast Startup Control RVDD 10 Ω AGC CAGC 10 µF DEC CDEC 47 nF Note 2 +5V CVDD 10 µF Figure 1. Application circuit of internal compensation capacitance option version MAS6180C1. 4 (13) DA6180C.000 26 November, 2010 TYPICAL APPLICATION (Continued) Note 1: Crystals The crystal as well as ferrite antenna frequencies are chosen according to the time-signal system (Table 1). More detailed crystal nominal frequency is normally specified for certain load capacitance but in MAS6180 filter circuit the load capacitance is not used. Effectively this means that most accurate filter frequency is achieved by using about 3 Hz higher frequency crystal than the received time signal frequency. For example in DCF77 application a 77.503 kHz crystal resonates at the desired DCF77 77.500 kHz frequency when the load capacitor is missing. Table 1. Time-Signal System Frequencies Time-Signal System Location Antenna Frequency Recommended Crystal Frequency DCF77 HGB MSF WWVB JJY BPC 77.5 kHz 75 kHz 60 kHz 60 kHz 40 kHz and 60 kHz 68.5 kHz 77.503 kHz 75.003 kHz 60.003 kHz 60.003 kHz 40.003 kHz and 60.003 kHz 68.505 kHz Germany Switzerland United Kingdom USA Japan China The crystal shunt capacitance C0 should be matched as well as possible with the internal shunt capacitance compensation capacitor CC of MAS6180. See Compensation Capacitance Options on table 2. Table 2 . Compensation Capacitance Options Device CC Crystal Description MAS6180C1 0.75 pF For low C0 crystals It should be noted that grounded crystal package has reduced shunt capacitance. This value is about 85% of floating crystal shunt capacitance. For example crystal with 1 pF floating package shunt capacitance can have 0.85 pF grounded package shunt capacitance. PCB traces of crystal should be kept at minimum to minimize additional parasitic capacitance which can cause capacitance mismatching. Table 3 below presents some crystal manufacturers having suitable crystals for time signal receiver application. Table 3. Crystal Manufacturers and Crystal Types in Alphabetical Order for Time Signal Receiver Application Manufacturer Crystal Type Dimensions Web Link Citizen Epson Toyocom KDS Daishinku Microcrystal Seiko Instruments CFV-206 C-2-Type C-4-Type DT-261 MS3V-T1R VTC-120 ø 2.0 x 6.0 ø 1.5 x 5.0 ø 2.0 x 6.0 ø 2.0 x 6.0 1.45 x 1.45 x 6.7 ø 1.2 x 4.7 http://www.citizen.co.jp/tokuhan/quartz/ http://www.epsontoyocom.co.jp/english/ http://www.kds.info/index_en.htm http://www.microcrystal.com/ http://www.sii-crystal.com 5 (13) DA6180C.000 26 November, 2010 TYPICAL APPLICATION (Continued) Note 2: AGC Capacitor The AGC and DEC capacitors must have low leakage currents due to very small signal currents through the capacitors. The insulation resistance of these capacitors should be at minimum 100 MΩ. Also probes with at least few 100 MΩ impedance should be used for voltage probing of the AGC and DEC pins. Electrolytic AGC capacitor should have voltage rating at least 25 V for low enough leakage. DEC capacitor can be low leakage chip capacitor. It is recommended to connect both AGC and DEC capacitors to VDD (see application figure 1) although VSS connection is also possible. The VDD connection provides better supply noise immunity because signals are referenced to VDD. Additionally leakage currents are minimized in this connection because in power down the AGC pin voltage is pulled to VDD (to minimum AGC gain) then corresponding to zero voltage over the AGC capacitor. Note 3: Power Down / Fast Startup Control Both power down and fast startup are controlled using the PDN pin. The device is in power down (turned off) if PDN = VDD and in power up (turned on) if PDN = VSS. Fast startup is triggered automatically by the falling edge of PDN signal, i.e., controlling device from power down to power up. The VDD must be high before falling edge of PDN to guarantee proper operation of fast startup circuitry. Before power up the device should have been kept in power down state at least 50ms. This guarantees that the AGC capacitor voltage has been completely pulled to VDD during power down. The startup time without proper fast startup control can be over minute but with fast startup it is shortened typically to few seconds. Note 4: Optional Control for AGC On/Hold AON control pin has internal pull up which turns AGC circuit on all the time if AON pin is left unconnected. Optionally AON control can be used to hold and release AGC circuit. Stepper motor drive of analog clock or watch can produce disturbing amount of noise which can shift the input amplifier gain to unoptimal level. This can be avoided by controlling AGC hold (AON=VSS) during stepper motor drive periods and releasing AGC (AON=VDD) when motors are not driven. The AGC should be in hold only during disturbances and kept on other time released since due to leakage the AGC voltage can change slowly even when in hold. Note 5: Ferrite Antenna The ferrite antenna converts the transmitted radio wave into a voltage signal. It has an important role in determining receiver performance. Recommended antenna impedance at resonance is around 100 kΩ. Low antenna impedance corresponds to low noise but often also to small signal amplitude. On the other hand high antenna impedance corresponds to high noise but also large signal. The optimum performance where signal-to-noise ratio is at maximum is achieved in between. The antenna should have also some selectivity for rejecting near signal band disturbances. This is determined by the antenna quality factor which should be approximately 100. Much higher quality factor antennas suffer from extensive tuning accuracy requirements and possible tuning drifts by the temperature. Antenna impedance Rant can be calculated using equation 1 where fres, L, Qant and C are resonance frequency, coil inductance, antenna quality factor and antenna tuning capacitor respectively. Antenna quality factor Qant is defined by ratio of resonance frequency fres and antenna bandwidth B (equation 2). Rant = 2π ⋅ f res ⋅ L ⋅ Qant = Qant = f res B Qant 1 = 2π ⋅ f res ⋅ C 2π ⋅ B ⋅ C Equation 1. Equation 2. Table 4 on next page presents some antenna manufacturers for time signal application. 6 (13) DA6180C.000 26 November, 2010 TYPICAL APPLICATION (Continued) Table 4. Antenna Manufacturers and Antenna Types in Alphabetical Order for Time Signal Application Manufacturer Antenna Type Dimensions Web Link C.E.C Coils AP/AR Antenna Bars HR Electronic GmbH Hitachi Metals 60716 (60 kHz) 60708 (77.5 kHz) AN-T702Sxx AN-T702Mxx AN-T702Lxx RCA-SMD-77A (77.5 kHz) RCA-SMD-60A (60 kHz) ACL80A (40 kHz) Premo Sumida http://www.ceccoils.com/CECWEB/index .aspx?lang=en ø 10 x 60 mm http://www.hrelectronic.com/ 19 x 5.5 x 6.3 mm 28 x 5 x 5 mm 50 x 5 x 5 mm 75 x 15 x 6.3 mm http://www.hitachimetals.co.jp/e/prod/prod06/p06_12.html http://www.grupopremo.com/ ø 10 x 80 mm www.sumida.co.jp/jeita/XJA021.pdf Note 6: Time Signal Software’s Pulse Width Recognition Limits The typical output pulse width specifications are presented in the electrical characteristics section on page 3. Due to process variations the typical output pulse width can differ from these. Additionally the output pulse widths can vary even more depending on the receiving antenna signal strength versus noise and disturbance conditions. That is why it is important that the time signal decoding software has appropriate tolerance limits for managing the output pulse width variations successfully. The table 5 presents recommended software pulse width tolerance limits for recognizing pulses of different time signals. Table 5. Recommended Software Pulse Width Recognition Limits for Different Time Signals Parameter Symbol Min Max Unit DCF77 Output Pulses MSF Output Pulses WWVB Output Pulses JJY60 Output Pulses JJY40 Output Pulses T 100ms T 200ms T 100ms T 200ms T 500ms T 200ms T 500ms T 800ms T 200ms T 500ms T 800ms T 200ms T 500ms T 800ms 40 140 50 170 400 100 400 700 100 400 700 100 400 700 130 250 160 300 600 300 600 900 300 600 900 300 600 900 ms ms ms ms ms 7 (13) DA6180C.000 26 November, 2010 MAS6180C SAMPLES IN DIL-20 PACKAGE 1 20 VSS 19 18 RFIM VDD 2 3 6 QI 7 AGC 8 MAS6180zz YYWW XXXXX.X QOP 4 QOM 5 17 RFIP 16 15 14 PDN 13 AON 9 12 DEC 11 OUT 10 Top Marking Definitions: YYWW = Year Week XXXXX.X = Lot Number zz =Sample Version PIN DESCRIPTION Pin Name VDD QOP QOM QI AGC OUT DEC AON PDN RFIP RFIM VSS Pin Type 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 NC P NC AO AO NC AI AO NC DO NC AO DI DI NC NC AI AI NC G Function Note Positive Power Supply Positive Quartz Filter Output Negative Quartz Filter Output 1 2 Quartz Filter Input for Crystal AGC Capacitor Receiver Output 3 Demodulator Capacitor AGC On Control Power Down Input 4 5 Positive Receiver Input Negative Receiver Input 6 6 Power Supply Ground A = Analog, D = Digital, P = Power, G = Ground, I = Input, O = Output, NC = Not Connected Notes: 1) QOM pin is electrically unconnected in MAS6180C1 version 2) Pin 6 between QOM and QI must be connected to VSS to eliminate DIL package lead frame parasitic capacitances disturbing the crystal filter performance. All other NC (Not Connected) type pins are also recommended to be connected to VSS to minimize noise coupling. 3) OUT = VSS when carrier amplitude at maximum; OUT = VDD when carrier amplitude is reduced (modulated) - the output is a current source/sink with |IOUT| > 5 µA - at power down the output is pulled to VSS (pull down switch) 4) AON = VSS means AGC off (hold current gain level); AON = VDD means AGC on (working) - Internal pull-up with current < 1 µA which is switched off at power down 5) PDN = VSS means receiver on; PDN = VDD means receiver off - Fast start-up is triggered when the receiver is after power down (PDN=VDD) controlled to power up (PDN=VSS) i.e. at the falling edge of PDN signal. 6) Receiver inputs RFIP and RFIM have both 1.4 MΩ biasing resistors towards VDD 8 (13) DA6180C.000 26 November, 2010 PIN CONFIGURATION & TOP MARKING FOR PLASTIC TSSOP-16 PACKAGE VSS RFIM VDD QOP QOM OUT 6180zz YYWW QI AGC RFIP PDN AON DEC Top Marking Definitions: zz = Version YYWW = Year Week PIN DESCRIPTION Pin Name Pin Type VDD QOP QOM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 P AO AO NC AI AO NC DO AO DI DI NC AI NC AI G QI AGC OUT DEC AON PDN RFIP RFIM VSS Function Positive Power Supply Positive Quartz Filter Output Negative Quartz Filter Output Note 1 2 Quartz Filter Input for Crystal AGC Capacitor Receiver Output Demodulator Capacitor AGC On Control Power Down Input 3 Positive Receiver Input 6 Negative Receiver Input Power Supply Ground 6 4 5 A = Analog, D = Digital, P = Power, G = Ground, I = Input, O = Output, NC = Not Connected Notes: 1) QOM pin is electrically unconnected in MAS6180C1 version 2) Pin 4 between QOM and QI must be connected to VSS to eliminate TSSOP package lead frame parasitic capacitances disturbing the crystal filter performance. All other NC (Not Connected) type pins are also recommended to be connected to VSS to minimize noise coupling. 3) OUT = VSS when carrier amplitude at maximum; OUT = VDD when carrier amplitude is reduced (modulated) - the output is a current source/sink with |IOUT| > 5 µA - at power down the output is pulled to VSS (pull down switch) 4) AON = VSS means AGC off (hold current gain level); AON = VDD means AGC on (working) - Internal pull-up with current < 1 µA which is switched off at power down 5) PDN = VSS means receiver on; PDN = VDD means receiver off - Fast start-up is triggered when the receiver is after power down (PDN=VDD) controlled to power up (PDN=VSS) i.e. at the falling edge of PDN signal. 6) Receiver inputs RFIP and RFIM have both 1.4 MΩ biasing resistors towards VDD 9 (13) DA6180C.000 26 November, 2010 PACKAGE (TSSOP-16) OUTLINES C E D Seating Plane B F G H A O Pin 1 B Detail A B L I I1 K P Section B-B J1 M J Dimension N Min A B C D E F G H I I1 J J1 K L M (The length of a terminal for soldering to a substrate) N O P Detail A Max 6.40 BSC 4.30 4.50 5.00 BSC 0.05 0.15 1.10 0.30 0.19 0.65 BSC 0.18 0.09 0.09 0.19 0.19 0° 0.24 0.50 0.28 0.20 0.16 0.30 0.25 8° 0.26 0.75 1.00 REF 12° 12° Unit mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm Dimensions do not include mold flash, protrusions, or gate burrs. All dimensions are in accordance with JEDEC standard MO-153. 10 (13) DA6180C.000 26 November, 2010 SOLDERING INFORMATION ◆ For Pb-Free, RoHS Compliant TSSOP-16 Resistance to Soldering Heat Maximum Temperature Maximum Number of Reflow Cycles Reflow profile According to RSH test IEC 68-2-58/20 260°C 3 Thermal profile parameters stated in IPC/JEDEC J-STD-020 should not be exceeded. http://www.jedec.org max 0.08 mm Solder plate 7.62 - 25.4 µm, material Matte Tin Seating Plane Co-planarity Lead Finish EMBOSSED TAPE SPECIFICATIONS Tape Feed Direction P0 D0 P2 A E1 F1 W D1 A A0 P Tape Feed Direction T Section A - A B0 S1 K0 Pin 1 Designator Dimension Min Max Unit A0 B0 D0 D1 E1 F1 K0 P P0 P2 S1 T W 6.50 5.20 6.70 5.40 mm mm mm mm mm mm mm mm mm mm mm mm mm 1.50 +0.10 / -0.00 1.50 1.65 7.20 1.20 11.90 1.85 7.30 1.40 12.10 4.0 1.95 0.6 0.25 11.70 2.05 0.35 12.30 11 (13) DA6180C.000 26 November, 2010 REEL SPECIFICATIONS W2 A D C Tape Slot for Tape Start N B W1 2000 Components on Each Reel Reel Material: Conductive, Plastic Antistatic or Static Dissipative Carrier Tape Material: Conductive Cover Tape Material: Static Dissipative Carrier Tape Cover Tape End Start Trailer Dimension A B C D N W1 (measured at hub) W2 (measured at hub) Trailer Leader Weight Leader Components Min 1.5 12.80 20.2 50 12.4 Max Unit 330 14.4 mm mm mm mm mm mm 18.4 mm 13.50 160 390, of which minimum 160 mm of empty carrier tape sealed with cover tape mm mm 1500 g 12 (13) DA6180C.000 26 November, 2010 ORDERING INFORMATION Product Code Product Description Capacitance Option MAS6180C1TC00 Single Band AM-Receiver IC with Differential Input CC = 0.75 pF MAS6180C1UC06 Single Band AM-Receiver IC with Differential Input EWS-tested wafer, diameter 8”, thickness 395 µm ± 5%. TSSOP-16, Pb-free, RoHS compliant, Tape & Reel CC = 0.75 pF Contact Micro Analog Systems Oy for other wafer thickness options. ◆ The formation of product code An example for MAS6180C1TC00: MAS6180 C 1 Product Design Capacitance option: name version CC = 0.75 pF TC Package type: TC = 400 µm thick EWS tested wafer 00 Delivery format: 00 = undiced wafer 05 = dies on tray 06 = tape & reel 08 = in tube LOCAL DISTRIBUTOR MICRO ANALOG SYSTEMS OY CONTACTS Micro Analog Systems Oy Kutomotie 16 FI-00380 Helsinki, FINLAND Tel. +358 10 835 1100 Fax +358 10 835 1109 http://www.mas-oy.com NOTICE Micro Analog Systems Oy reserves the right to make changes to the products contained in this data sheet in order to improve the design or performance and to supply the best possible products. Micro Analog Systems Oy assumes no responsibility for the use of any circuits shown in this data sheet, conveys no license under any patent or other rights unless otherwise specified in this data sheet, and makes no claim that the circuits are free from patent infringement. Applications for any devices shown in this data sheet are for illustration only and Micro Analog Systems Oy makes no claim or warranty that such applications will be suitable for the use specified without further testing or modification. 13 (13)