SUS01 1W DC-DC Unregulated Single Output Converter series Features : 1000VDC I/O isolation Internal SMD technology Built-in EMI filter Cooling by free air convection Non-conductive plastic case Dual in line package 100% burn-in test Low cost / High reliability 2 years warranty SELECTION GUIDE ORDER NO. SUS01L-05 SUS01M-05 SUS01N-05 SUS01O-05 DC OUTPUT VOLTAGE 5V OUTPUT CURRENT RANGE 0 ~ 200mA EFFICIENCY 73% 74% 72% 74% SUS01L-12 SUS01M-12 SUS01N-12 SUS01O-12 ORDER NO. DC OUTPUT VOLTAGE 12V OUTPUT CURRENT RANGE 0 ~ 84mA EFFICIENCY 78% SUS01L-09 SUS01M-09 SUS01N-09 SUS01O-09 75% 79% 80% 77% SUS01L-15 SUS01M-15 SUS01N-15 SUS01O-15 9V 0 ~ 111mA 15V 0 ~ 67mA 83% 83% 79% 82% 83% 83% 10.8 ~ 13.2V 12V 21.6 ~ 26.4V 24V 43.2 ~ 52.8V 48V 4.5 ~ 5.5V 5V 10.8 ~ 13.2V 12V 21.6 ~ 26.4V 24V 43.2 ~ 52.8V 48V 112mA 55mA 28mA 280mA 112mA 55mA 28mA 11mA 10mA 3mA 21mA 11mA 10mA 3mA 82% SPECIFICATION RATED POWER 1W RIPPLE & NOISE (max.) Note.2 100mVp-p LINE REGULATION Note.3 1.2% for 1% input variation LOAD REGULATION Note.4 8.0% VOLTAGE ACCURACY 50KHz min. VOLTAGE RANGE NORMAL VOLTAGE 4.5 ~ 5.5V 5V INPUT CURRENT INPUT 2.0% SWITCHING FREQUENCY Full load 280mA No load 21mA FILTER Capacitor type Fuse recommended PROTECTION Momentary OVERLOAD Protection type : Broken Momentary PROTECTION SHORT CIRCUIT Protection type : Broken WORKING TEMP. -25 ~ +71 WORKING HUMIDITY 20% ~ 90% RH non-condensing ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION WITHSTAND VOLTAGE SAFETY & ISOLATION RESISTANCE EMC ISOLATION CAPACITANCE MTBF OTHERS DIMENSION -25 ~ +105 80pF max. 700khrs min. MIL-HDBK-217F(25 ) 22.6*9.9*8.4mm or 0.89"*0.39"*0.33" inch (L*W*H) Mechanical Specification Unit: mm (inch) Derating Curve Pin Configuration 3.81 (0.15) 9.9 (0.39) 0.5 (0.02) 22.6 (0.89) 12.7 (0.50) 1 BOTTOM VIEW 11 10 9 , 10 ~ 95% RH 0.03% / (0 ~ 50 ) 10 ~ 500Hz, 2G 10min./1 cycle, period for 60min. each along X, Y, Z axes I/P-O/P:1KVDC I/P-O/P: 100M Ohms / 500VDC / 25 / 70% RH 3.1g WEIGHT 16 (Refer to output load derating curve) 6 7 8 Pin No. Output 1 & 16 +Vin 6 & 11 7 & 10 -Vout +Vout 8 & 9 -Vin 100 LOAD (%) OUTPUT 80 2.54 (0.10) 7.62 (0.30) NOTE 8.4 (0.33) -25 0 25 50 60 71 100 Ta ( ) 1.All parameters are specified at normal input, rated load, 25 70% RH ambient. 2.Ripple & noise are measured at 20MHz by using a 12" twisted pair terminated with a 0.1uf & 47uf capacitor. 3.Line regulation is measured from low line to high line at rated load. 4.Load regulation is measured from 20% to 100% rated load. File Name: SUS01-SPEC 2011-04-25