MICRODC WRB2405ZT-1W5

WRA-ZT-1W5&WRB-ZT-1W5 Series
1.5W,WIDE INPUT ISOLATED&REGULATED SINGLE/DUAL OUTPUT DC/DC CONVERTER MINIATURE SMD PACKAGE
SELECTION GUIDE
Input
Order code
Output
Voltage(VDC)
Voltage
(VDC)
Current(mA)
Efficiency
(%,Typ)
Nominal
Range
Max.*
Max.
Min.
WRA2405ZT-1W5
24
9-36
40
±5
±150
±15
74
WRA2412ZT-1W5
24
9-36
40
±12
±63
±6
77
WRA2415ZT-1W5
24
9-36
40
±15
±50
±5
75
WRB2403ZT-1W5
24
9-36
40
3.3
500
50
71
◆4:1 wide input voltage range
WRB2405ZT-1W5
24
9-36
40
5
300
30
76
◆Short circuit protection(automatic recovery)
WRB2409ZT-1W5
24
9-36
40
9
167
17
76
WRB2412ZT-1W5
24
9-36
40
12
125
12
79
WRB2415ZT-1W5
24
9-36
40
15
100
10
80
◆Operating temperature: -40℃ ~ +85℃
WRA4805ZT-1W5
48
18-72
80
±5
±150
±15
74
◆No heatsink required
WRA4812ZT-1W5
48
18-72
80
±12
±63
±6
76
WRA4815ZT-1W5
48
18-72
80
±15
±50
±5
76
WRB4803ZT-1W5
48
18-72
80
3.3
500
50
72
◆MTBF>1,000,000 hours
WRB4805ZT-1W5
48
18-72
80
5
300
30
75
◆RoHS Compliance
WRB4809ZT-1W5
48
18-72
80
9
167
17
78
WRB4812ZT-1W5
48
18-72
80
12
125
12
77
WRB4815ZT-1W5
48
18-72
80
15
100
10
77
FEATURES
◆SMD package
◆1500VDC isolation
◆No external component required
*Input voltage can't exceed this value, or will cause the permanent damage.
MODEL SELECTION
WRA①24②05③Z④ T⑤-1W5⑥
①Product Series
③Output Voltage
⑤SMD Package
②Input Voltage
④Wide (4:1) Input Range
⑥Rated Power
APPLICATIONS
The
WRA_ZT-1W5&WRB_ZT-1W5
series
are
specially designed for applications where a wide range
input voltage power supplies are isolated from the input
COMMON SPECIFICATIONS
power supply in a distributed power supply system on a
circuit board.
Parameter
Test conditions
Min.
Typ.
Storage humidity
These products apply to:
Operating temperature
-40
1) Where the voltage of the input power supply is wide
Storage Temp. range
-55
range(voltage range ≤4:1);
Temp. rise at full load
2) Where isolation is necessary between input and
Lead temperature
output (isolation voltage ≤1500VDC);
Short circuit protection
3 here the regulation of the output voltage and the
Cooling
output ripple noise are demanded.
Case Material
MTBF
Max.
%
85
℃
125
℃
℃
15
1.5mm from case for 10 seconds
℃
300
Continuous, automatics recovery
Free air convection
Epoxy Resin (UL94-V0)
1000
Weight
K hours
5.2
MICRODC reserves the copyright
http://www.microdc.cn
Units
95
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
Page 1 of 3
g
WRA-ZT-1W5&WRB-ZT-1W5 Series
ISOLATION SPECIFICATIONS
Parameter
TYPICAL TEMPERATURE CURVE
Test conditions
Min.
Isolation voltage
Tested for 1 minute and 1mA max
1500
Isolation resistance
Test at 500VDC
1000
Isolation capacitance
Input/Output, 100KHz/1V
Typ.
Max
Units
VDC
MΩ
1000
µF
OUTPUT SPECIFICATIONS
Parameter
Test conditions
Min.
Typ.
Max
Units
Output power
Refer to products program
1.5
W
Positive voltage accuracy
Refer to recommended circuit
0.15
±1
±3
%
Negative voltage accuracy
Refer to recommended circuit
±3
±5
%
Load regulation
From 10% to 100% load
±0.5
±1.5*
%
Line regulation
Input voltage from low to high
±0.2
±0.75
%
Temperature Drift (Vout)
Refer to recommended circuit
±0.03
%/℃
Output ripple & noise**
20MHz Bandwidth
35
100
mVp-p
Switching Frequency
100% load, input voltage range
550
kHz
* Dual output models unbalanced load:±5%.
**Test ripple and noise by “parallel cable”method. See detailed operation instructions at Testing of Power
Converter section, application notes.
RECOMMENDED CIRCUIT
APPLICATION NOTE
1) Requirement on output load
In order to ensure the product operate efficiently and reliably,
in addition to a max
load), a minimum load is specified for this kind of DC/DC converter. Make sure the
load (namely full
specified
range
of
input voltage is not exceeded, the minimum output load no less than 10% load
load. If the actual load is less
than the specified minimum load, the output ripple may increase sharply while its efficiency
and reliability
will reduce greatly. If the actual output power is very small, please add an appropriate resistor as extra
loading, or contact our company for other lower output power products.
2) Recommended Circuit
All the WRA_ZT-1W5 & WRB_ZT-1W5 series have been tested according to the following
recommended testing circuit before leaving factory. This series should be tested under load (see Figure 1).
If you want to further decrease the input/output ripple, you can increase capacitance properly or choose
capacitors with low ESR. However, the capacitance of the output filter capacitor must be proper. If the
capacitance is too big, a startup problem might arise. For every channel of output, provided the safe and
reliable operation is ensured, the maximum capacitance of its filter capacitor sees (Table 1). General:
Cin: 10µF~47µF
Cout: 10µF/100mA
3) Input Current
When it is used in unregulated power supply, be sure that the fluctuating range of the power supply
and the rippled voltage do not exceed the module standard. Input current of power supply should afford the
flash startup current of this kind of DC/DC module (Figure 2)
General: Ip ≤1.6*Iin-max
4) No parallel connection or plug and play
http://www.microdc.cn
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
Page 2 of 3
WRA-ZT-1W5&WRB-ZT-1W5 Series
OUTLINE DIMENSIONS & FOOTPRINT DETAILS
MECHANICAL DIMENSIONS
RECOMMENDED FOOTPRINT(TOP VIEW)
TUBE OUTLINE DIMENSIONS
Note:
1. The load shouldn't be less than 10%, otherwise ripple will increase dramatically.
2.
Operation under 10% load will not damage the converter; However, they may not meet all specification listed.
3.
Capacitor MAX load tested at input voltage range and full load.
4. All specifications measured at Ta=25℃, humidity<75%, nominal input voltage and rated output load unless otherwise specified.
5.
Only typical models listed, other models may be different, please contact our technical person for more details.
6.
In this datasheet, all the test methods of indications are based on corporate standards.
RoHS COMPLIANT INFORMATION
Microdc Professional Power Module,Inc.
This series is compatible with RoHS soldering systems with a peak wave solder temperature of 300°C
Tel:0086-20-86000646 E-mail:[email protected]
for 10 seconds. The pin termination finish on the SIP package type is Tin Plate, Hot Dipped over Matte
Website:http://www.microdc.cn
Tin with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in this series are
Microdc Professional Power module,Inc.makes no representation that
backward compatible with Sn/Pb soldering systems.
the use of its products in the circuits described herein, or the use of other
technical information contained herein, will not infringe upon existing or
REACH COMPLIANT INFORMATION
future patent rights. Specifications are subject to change without notice.
This series has proven that this product does not contain harmful chemicals, it also has harmful chemical
©2010
substances through the registration, inspection and approval.
Microdc Professional Power Module, Inc. Guangzhou
http://www.microdc.cn
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
Page 3 of 3