[ UTZ-SC0319_2 ] 2012/10/02 Blue Laser Diode NDB4216E Engineering Sample Features Outline Dimension • Optical Output Power: CW 100mW • Can Type: φ 5.6 mm Floating Mounted with Photo Diode and Zener Diode Unit (mm) ( 0 + .03 0 6 5. 1. 6) Φ Absolute Maximum Ratings Φ (90°) Item Symbol Optical Output Power Po Absolute Maximum Ratings 120 Allowable Reverse Current Ir (LD) 85 mA PD Reverse Voltage Vr (PD) 5 V Storage Temperature Tstg -40 ~ 85 °C Operating Case Temperature Tc -10 ~ 60 °C (0.4) 1.2± 0.1 2.3±0.2 Φ 3.55±0.1 (Tc=25°C) Max Unit 100 mW 0.25±0.03 Z+ Φ 4.2±0.2 Glass Thickness 1.0±0.1 0.4±0.1 mW Emitting Point (1.3) Reference Plane 6.5±1.0 Initial Electrical/Optical Characteristics Emitting Point Unit 4×Φ 0.43±0.08 Item Optical Output Power Condition CW Symbol Po Min - Typ. - Peak Wavelength Po=100mW λp 450 - 460 nm Threshold Current CW Ith 15 30 55 mA 4 Operating Current Po=100mW Iop 80 110 150 mA Y+ Slope Efficiency CW η 0.7 1.2 1.7 W/A Operating Voltage Po=100mW Vop 4.0 5.2 6.5 V Parallel Beam Po=100mW Divergence* Perpendicular Beam Parallel Po=100mW Pointing Accuracy Perpendicular Monitor Current** Po=100mW θ// 6.0 8.5 12.5 ° θ⊥ 17.0 23.0 27.0 ° ∆θ// -2.5 - 2.5 ° ∆θ⊥ -3.0 - 3.0 ° Im 0.2 1.0 2.0 mA 3 X+ 1 2 Φ 2.0±0.2 ( ) are reference figures Pin Connection * Full angle at 50% from peak intensity This model has a Zener Diode built in as a protection circuit against static ** Monitor Current is short time power reference purpose only. Not guaranteed for electricity. accuracy. All figures in this specification are measured by Nichia's method and may contain measurement deviations. This model is Engineering Sample for evaluation or design purpose only. Life time is not guaranteed. The above specifications are for reference purpose only and subjected to change without prior notice. Safety of Laser light Laser Light can damege the human eyes and skin. Do not expose the eye or skin to any laser light directly and/or through optical lens. When handling the LDs, wear appropriate safety glasses to prevent laser light, even any reflections from entering to the eye. Focused laser beam through optical instruments will increase the chance of eye hazard. These LDs are classified in Class 4 of IEC60825-1 and 21 CFR Part 1040.10 Safety Standards. It is absolutely necessary to take overall safety measures against User's modules, equipment and systems into which Nichia LDs are incorporated and/or integrated. NICHIA CORPORATION http://www.nichia.co.jp HEADQUARTERS 491 Oka, Kaminaka-Cho, Anan-Shi, TOKUSHIMA 774-8601, JAPAN PHONE: +81-884-22-2311 FAX: +81-884-21-0148 CONTACT TOKYO SALES OFFICE 13F Tamachi Center Building 34-7, Shiba 5-Chome, Minato-Ku, TOKYO 108-0014, JAPAN PHONE: +81-3-3456-3108 FAX: +81-3-5440-7330 -1- [ UTZ-SC0319_2 ] 2012/10/02 Typical Characteristics Optical Output Power vs. Forward Current Forward Voltage vs. Forward Current 7 Tc=-10℃ ℃ Tc=20℃ ℃ Tc=40℃ ℃ Tc=60℃ ℃ 100 80 6 Forward Voltage Vf [V] Optical Output Power Po [mW] 120 60 40 20 5 4 3 Tc=-10 ℃ Tc=20 ℃ Tc=40℃ ℃ Tc=60℃ ℃ 2 1 0 0 0 20 40 60 80 100 120 0 140 20 40 80 100 120 140 Forward Current If [mA] Forward Current If [mA] Threshold Current vs. Case Temperature Peak Wavelength vs. Case Temperature 55 460 Peak Wavelength λ p [nm] 50 45 40 35 30 25 20 15 459 458 457 456 455 -10 0 10 20 30 40 50 60 -10 0 10 Case Temperature Tc [ºC] -20 30 40 50 60 Relative Optical Output Power [a.u.] Spectrum θ/ / θ⊥ -40 20 Case Temperature Tc [ºC] Far Field Pattern Relative Intensity [a.u.] Threshold Current Ith [mA] 60 0 20 40 450 Angle θ [°] 452 454 456 Wavelength λ [nm] -2- 458 460 [ UTZ-SC0319_2 ] 2012/10/02 Cautions (1) Operating method The LD shall change its forward voltage requirement and optical output power according to temperature change. Also, the LD will require more operation current to maintain same output power as it degrades. Confirm that the optical output power generated by spike current when switching on and off does not exceed the maximum absolute rating. Also, employ appropriate countermeasures to reduce chattering and/or overshooting in the Circuit. (2) Static Electricity Static electricity or electrical surges will reduce and degrade the reliability of the LDs. It is recommended to use a wrist strap or anti-electrostatic glove when handling the Product. (3) Absolute Maximum Rating Active layer of LDs shall have high current density and generate high electric field during its operation. In order to prevent excessive damage, the LD must be operated strictly below Absolute Max Rating. (4) Others Nichia LDs described in this brochure are intended to be used for ordinary electronic equipment (such as office equipment, communications equipment, measurement instruments and household appliances). Consult Nichia’s sales staff in advance for information on the applications in which exceptional quality and reliability are required, particularly when the failure or malfunction of the LDs may directly jeopardize life or health (such as for airplanes, aerospace, submersible repeaters, nuclear reactor control systems, automobiles, traffic control equipment, life support systems and safety devices). The Purchaser must acknowledge that any LD can be failed statically and must design its equipments fail safe design. Prior to use of the LD, please confirm that the LD, as described in Nichia’s specifications, meets the life expectancy needs of, and provides the features required by the Circuit and any related modules, equipment and/or systems. Nichia prohibit Purchaser from reverse engineering, disassembling, or taking any other steps to derive the structure or design of the LD. The appearance and specifications of the product may be modified for improvement without notice. The formal specifications must be exchanged and signed by both parties before large volume purchase begins. No unauthorized transmission or reproduction of this document, either in whole or in part, is permitted. -3-