PNSPO ® OMRON NETWORK PRODUCTS P1RX6A-SX51-01M Product Specification Sheet ORIGINATOR: PNSPO! B. Peters P1RX6A-SX51-01M Product Specification Sheet CONFIDENTIAL INFORMATION DATE: 8/7/09 DOCUMENT NO. DOC000925 SHEET 1 OF 9 REV D PNSPO ® OMRON NETWORK PRODUCTS 1.0 Description The P1RX6-SX51-01M (RX-SX51) is an optical module that receives and converts an optical HDMI™ signal. The RX-SX51 incorporates a bi-directional optical subassembly (OSA) to receive an optical HDMI™ video signal, along with the HDCP/EDID/CEC functionality, from one strand of multimode fiber and restore it to its original electrical HDMI™ signal. The HDCP encoding remains intact and unmodified throughout the entire process. 2.0 Features • • • • • • 5 receive lanes and 1 transmit lane over 1 multimode fiber Compatible with HDMI™ compliant sources and sinks Scalable to HDMI™ 1.3a 16-bit color On-board hardware and firmware for HDCP/EDID/CEC functionality Outputs TMDS signals through its 40 pin plug-down connector Automatic laser disable upon fiber disconnect This device is EXTREMELY SENSITIVE to Electrostatic Discharge (ESD). At a minimum, all handling must be performed in accordance with an ANSI-compliant ESD Control Program (ANSI/ESD S20.20-2007) to mitigate possible ESD-induced damage. Reliability and life of the device will be adversely affected if these precautions are not met. This device is a Class 3R Laser device (per IEC 60825-1:2007) and can cause damage to eye sight if used improperly. Refer to ANSI Z136 for proper handling and usage of Class 3R devices. HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. ORIGINATOR: PNSPO! B. Peters P1RX6A-SX51-01M Product Specification Sheet CONFIDENTIAL INFORMATION DATE: 8/7/09 DOCUMENT NO. DOC000925 SHEET 2 OF 9 REV D PNSPO ® OMRON NETWORK PRODUCTS 3.0 Absolute Maximum Ratings Parameter 1, 3 Storage Temperature 3.3V Supply Voltage 5.0V Supply Voltage Operating Surface Temperature 2 Operating Humidity 3 Durability – SC Connector Durability – Plug-down Connector 4.0 Symbol Min Tst VCC1 VCC2 Ta RH -40 -0.3 -0.5 0 Typ Max Units 85 3.6 6.0 65 80 °C V V °C % cycles cycles Max Units 200 50 Optical Characteristics – High-speed Lanes Parameter (per lane) Symbol Min Typ Wavelength – Lane 0 778 nm Wavelength – Lane 1 800 nm Wavelength – Lane 2 825 nm Wavelength – Lane 3 Data Rate 4 850 SX51V-01M SX51D-01M Peak Optical Input Power OMA Sensitivity Pin 5 -14.25 -16.00 nm 1.65 3.50 Gb/s 4.0 dBm dBm 1 Stresses listed may be applied without causing damage. Functionality at or above the values listed is not implied. Exposure to these values for extended periods may affect reliability. 2 See outline drawing for measurement point. 3 Non condensing, 80% RH. 4 Requires DC-balanced data pattern. Measured with input signals conforming to HDMI™ rev 1.3a, section 4.2.5, figure 4-20. 5 Optical Modulation Amplitude. Based on an unstressed input signal. ORIGINATOR: PNSPO! B. Peters P1RX6A-SX51-01M Product Specification Sheet CONFIDENTIAL INFORMATION DATE: 8/7/09 DOCUMENT NO. DOC000925 SHEET 3 OF 9 REV D PNSPO ® OMRON NETWORK PRODUCTS 5.0 Electrical Specifications – High-speed Lanes Parameter Symbol Low Frequency Cutoff Total Jitter (RMS), per lane 6 Differential Output Voltage 6.0 7 Min Typ Max Units FCUTOFF 175 kHz TJ1 10 ps VOD 500 mVp-p Operating 3.3V Supply Voltage VCC1 Operating 3.3V Supply Current ICC1 Operating 5.0V Supply Voltage VCC2 Operating 5.0V Supply Current ICC2 3.15 4.75 3.30 5 3.45 V 160 mA 5.25 V 35 mA Optical Characteristics – Low-speed Lanes Photodiode Parameter Symbol Min Wavelength - Lane 4 Data Rate Maximum Optical Input Power Laser Parameter Min Wavelength - Lane 5 Data Rate Average Optical Power Pavg Max Units 911 nm 5 Mb/s Pin Symbol 8 Typ Typ 8 dBm Max Units 980 nm 5 Mb/s -0.5 dBm 6 Based on a jitter-free source Differential back-terminated CML outputs 8 I= 5mA ;, T=25C. 7 ORIGINATOR: PNSPO! B. Peters P1RX6A-SX51-01M Product Specification Sheet CONFIDENTIAL INFORMATION DATE: 8/7/09 DOCUMENT NO. DOC000925 SHEET 4 OF 9 REV D PNSPO ® OMRON NETWORK PRODUCTS 7.0 HDMI™ Signal Parameters HDMI™ Signal Parameter 9 Symbol Min Typ Max Units HDMI™ Input Signal – SCLIH,SDAIH VIH 3.5 5.75 V HDMI™ Input Signal – SCLIL,SDAIL VIL -0.5 1.5 V Hot Plug Detect High HPDH 2.0 5.3 V Hot Plug Detect Low HPDL 0 0.8 V +5V Power pin Signal VS 4.7 5.3 Vdc Sink Current for 5V Power Pin Signal Isink 55 mA CEC 10 Output Voltage Logic ‘0’ VCEC0 0 0.6 V CEC Output Voltage Logic ‘1’ High to Low Input Voltage Threshold Logic ‘0’ Low to High Input Voltage Threshold Logic ‘1’ VCEC1 2.5 3.63 V VCECT0 0.0 0.8 V VCECT1 2.0 3.63 V CEC Rise Time (10% to 90%) tCECRise 250 μs CEC Fall Time tCECFall 50 μs Status Signal Functional Table 11 8.0 Condition Status Signal Pin Output Source Cable Source Status Sink Cable Sink Status Optical Cable SS 1 SS 2 SS 3 SS 4 X X X X D T 0 0 0 C ON C ON C 0 0 0 0 C OFF C ON C 0 0 0 1 C X D X C 0 0 1 1 C X C OFF C 0 0 1 1 D X X X C 0 1 1 1 X D C T 0 1 Does Not Affect Outcome Disconnected Connected Toggles Between 0 and 1 at ~ 10Hz 0 Volts 5 Volts 9 Reference I2C-Bus Specification v2 and HDMI™ rev 1.3a. Supports up to 100kHz bus speed. The firmware version installed in the module must be version 2.10.06 or higher for CEC functionality. Update to version 2.10.06 or higher if the current version is not at this revision level. Refer to P1_X6-SX51-01M Bootloader Manual for updating details. 11 Status signal table represents typical output. Variances in status signals may occur between different manufacturers and/or models of sources and sinks. 10 ORIGINATOR: PNSPO! B. Peters P1RX6A-SX51-01M Product Specification Sheet CONFIDENTIAL INFORMATION DATE: 8/7/09 DOCUMENT NO. DOC000925 SHEET 5 OF 9 REV D PNSPO ® OMRON NETWORK PRODUCTS 9.0 Firmware 12 The firmware utilized with the P1RX6-SX51-01M has been evaluated with the following functional tests: 9.1 HDCP Compliance Test (Source) 1A-01 through 1A-09, 1B-01 through 1B-06 9.2 HDCP Compliance Test (Sink) 2C-01 through 2C-04 9.3 HDCP Compliance Test (Repeater) 3C-I-01 through 3C-I-07, 3C-II-01 through 3C-II-09, 3A-01 through 3A-05, 3B-01 through 3B-05 9.4 EDID for HDMI™ Compliance Test (Display sink devices) 8-1, 8-2, 8-3, 8-17, 8-18, 8-19 9.5 CEC Compliance Tests 7-1, 7-2, 8.1, 8.2, 9.1 through 9.5, 9.7-1, 10.1.1.1-1, 10.1.2, 10.2.3, 11.1.2-2, 11.1.3-2, 11.1.6-1 through 11.1.6-4, 11.2.1-1, 11.2.2-2, 11.2.2-3, 11.2.3-2, 11.2.6-1, 11.2.6-2, 11.2.7-3 through 11.2.7-6, 11.2.7-12, 11.2.7-13, 11.2.14-1, 12-1 through 12-3 10.0 Connectivity The P1RX6-SX51-01M will support up to eight Key Selection Vectors (KSV) allowing for up to eight HDCP compliant devices to be connected downstream from the SX51-01M link. 11.0 Laser Safety The P1RX6-SX51-01M meets Class-3R requirements. Use proper eye protection and handling practices per ANSI Z136. 12.0 Patents This product contains the following patents or patents pending: 6201908, 6396978, 6456757, 6558046, 6572278, 6652161. 12 Firmware is not warranted for interoperability with all HDMITM sources and sinks. ORIGINATOR: PNSPO! B. Peters P1RX6A-SX51-01M Product Specification Sheet CONFIDENTIAL INFORMATION DATE: 8/7/09 DOCUMENT NO. DOC000925 SHEET 6 OF 9 REV D PNSPO ® OMRON NETWORK PRODUCTS 13.0 ROSA Module Pin Numbers and Descriptions The SX51 RX Module utilizes a 40 pin plug-down connector. Recommended mounting position is on the top of the board and secured in place with mounting screws located along the bottom face of the module enclosure. For information on the specifications of the connector, contact Hirose (DF12 (5.0)-40DP-0.5V). Pin # Name Description 1 TMDS 2 + Positive differential TMDS 2 signal (850nm) 2 VCC1 +3.3V Power Supply 3 GND Ground 4 VCC1 +3.3V Power Supply 5 TMDS 2 - Negative differential TMDS 2 signal (850nm) 6 13 NC 13 Do Not Connect 7 TMDS 1 + Positive differential TMDS 1 signal (825nm) 8 NC Do Not Connect 9 GND Ground 10 NC Do Not Connect 11 TMDS 1 - Negative differential TMDS 1 signal (825nm) 12 NC Do Not Connect 13 TMDS 0 + Positive differential TMDS 0 signal (800nm) 14 SS 1 Fiber Connect Status Signal 15 GND Ground 16 SS 2 5V Source Status Signal 17 TMDS 0 - Negative differential TMDS 0 signal (800nm) 18 SS 3 Hot Plug Sink Status Signal 19 CLK + Positive differential CLK signal (778nm) 20 SS 4 Video Detect Status Signal NC = Do not connect this pin ORIGINATOR: PNSPO! B. Peters P1RX6A-SX51-01M Product Specification Sheet CONFIDENTIAL INFORMATION DATE: 8/7/09 DOCUMENT NO. DOC000925 SHEET 7 OF 9 REV D PNSPO ® OMRON NETWORK PRODUCTS ROSA Module Pin Numbers and Descriptions (Cont’d) Pin # Name Description 21 GND Ground 22 Reserved Reserved for Omron future use – Do Not Connect 23 CLK - Negative differential CLK signal (778nm) 24 NC Do Not Connect 25 SINK_CEC 26 NC Do Not Connect 27 NC Do Not Connect 28 NC Do Not Connect 29 SINK_SCL 30 NC Do Not Connect 31 SINK_SDA Sink Data 32 NC Do Not Connect 33 GND 14 Sink CEC Sink Clock 15 Ground Module Reset 16 34 Reset (Must be asserted to +5V for normal operation) 35 SINK_5V 36 VCC2 +5V Power Supply 37 SINK_HPD Sink Hot Plug Detect signal 38 VCC2 +5V Power Supply 39 GND Ground 40 GND Ground Sink 5V signal 17 14 Internal 27.4kΩ pull-up to 3.3v Internal 2kΩ pull-up to 5v 16 See Information Package for Mechanical Reset Circuit 17 Internal 10kΩ pull-down to ground 15 ORIGINATOR: PNSPO! B. Peters P1RX6A-SX51-01M Product Specification Sheet CONFIDENTIAL INFORMATION DATE: 8/7/09 DOCUMENT NO. DOC000925 SHEET 8 OF 9 REV D PNSPO ® OMRON NETWORK PRODUCTS 14.0 Dimensions The SX51 RX Module is designed to work with a standard SC ferrule only. Insertion of any other type may result in damage. For dust cap information, contact L-Com (DSTCP-SC). Dimensions and orientation are for reference only. **Temperature measurement point All dimensions are in mm. ORIGINATOR: PNSPO! B. Peters P1RX6A-SX51-01M Product Specification Sheet CONFIDENTIAL INFORMATION DATE: 8/7/09 DOCUMENT NO. DOC000925 SHEET 9 OF 9 REV D