ORIONFANS P1TX6A-SX51-01M

PNSPO
®
OMRON NETWORK PRODUCTS
P1TX6A-SX51-01M
Product Specification Sheet
ORIGINATOR:
PNSPO!
B. Peters
P1TX6A-SX51-01M Product Specification Sheet
CONFIDENTIAL INFORMATION
DATE:
8/7/09
DOCUMENT NO.
DOC000924
SHEET 1 OF 10
D
PNSPO
®
OMRON NETWORK PRODUCTS
1.0
Description
The P1TX6-SX51-01M (TX-SX51) is an optical module
that transmits an HDMI™ signal on one strand of
multimode fiber. The TX-SX51 incorporates a bidirectional optical subassembly (OSA) to convert and
transmit an uncompressed electrical HDMI™ video
signal, along with the HDCP/EDID/CEC functionality,
over distances of up to 1000m.
2.0
•
•
•
•
•
•
Features
5 transmit lanes and 1 receive lane over 1 multimode fiber
Compatible with HDMI™ compliant sources and sinks
Scalable to HDMI™ 1.3a 16-bit color
On-board hardware and firmware for HDCP/EDID/CEC functionality
Accepts TMDS inputs directly into its 40 pin plug-down connector
Automatic laser disable upon fiber disconnect
This device is EXTREMELY SENSITIVE to Electrostatic Discharge (ESD). At a minimum, all handling must be
performed in accordance with an ANSI-compliant ESD Control Program (ANSI/ESD S20.20-2007) to mitigate
possible ESD-induced damage. Reliability and life of the device will be adversely affected if these precautions are
not met.
This device is a Class 3R Laser device (per IEC 60825-1:2007) and can cause damage to eye sight if used improperly. Refer to ANSI
Z136 for proper handling and usage of Class 3R devices.
HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
ORIGINATOR:
PNSPO!
B. Peters
P1TX6A-SX51-01M Product Specification Sheet
CONFIDENTIAL INFORMATION
DATE:
8/7/09
DOCUMENT NO.
DOC000924
SHEET 2 OF 10
D
PNSPO
®
OMRON NETWORK PRODUCTS
3.0
Absolute Maximum Ratings
Parameter
Storage Temperature 1, 3
3.3V Supply Voltage
5.0V Supply Voltage
Operating Surface Temperature 2
Operating Humidity 3
Durability – SC Connector
Durability – Plug-down Connector
4.0
Symbol
Min
Tst
VCC1
VCC2
Ta
RH
-40
-0.3
-0.5
0
Typ
Max
Units
85
3.6
6
65
80
°C
V
V
°C
%
cycles
cycles
Max
Units
200
50
Optical Characteristics – High-speed Lanes
Parameter (per lane)
Average Optical Power, per Lane
Symbol
4
Optical Modulation Amplitude
Pout
Min
Typ
-3.0
0.0
-6.25
dBm
dBm
Center Wavelength – Lane 0
778
nm
Center Wavelength – Lane 1
800
nm
Center Wavelength – Lane 2
825
nm
Center Wavelength – Lane 3
850
nm
1
Stresses listed may be applied without causing damage. Functionality at or above the values listed is not implied. Exposure to these
values for extended periods may affect reliability.
2
See outline drawing for measurement point.
3
Non condensing, 80% RH.
4
I= 5mA, T=25C.
ORIGINATOR:
PNSPO!
B. Peters
P1TX6A-SX51-01M Product Specification Sheet
CONFIDENTIAL INFORMATION
DATE:
8/7/09
DOCUMENT NO.
DOC000924
SHEET 3 OF 10
D
PNSPO
®
OMRON NETWORK PRODUCTS
5.0
Electrical Specifications – High-speed Lanes
Parameter
Symbol
Min
Typ
Max
Units
1.65
3.50
Gb/s
Data Rate per Lane 5
P1TX6-SX51V-01M
P1TX6-SX51D-01M
Total Jitter (RMS), per lane
6
TJ1
10
Input Differential Impedance
6.0
ps
100
ohm
Differential Input Voltage 7
320
2000
mVp-p
Single-ended Input Voltage
Common mode input voltage
(AC-coupled input)
160
0.85
1000
VCC
mVp-p
V
V
3.45
V
235
mA
5.25
V
35
mA
2.6
Operating 3.3V Supply Voltage
VCC1
Operating 3.3V Supply Current
ICC1
Operating 5.0V Supply Voltage
VCC2
Operating 5.0V Supply Current
ICC2
3.15
4.75
3.30
5
Optical Characteristics – Low-speed Lanes
Laser Parameter
Symbol
Min
Wavelength - Lane 4
Typ
Pavg
Photodiode Parameter
Symbol
Min
Wavelength - Lane 5
5
Mb/s
-0.5
dBm
Typ
Max
Units
980
nm
5
Mb/s
Data Rate
Maximum Optical Input Power
Units
nm
Data Rate
Average Optical Power
Max
911
Pin
8
dBm
5
Measured with input signals conforming to HDMI™ rev 1.3a, section 4.2.4, figure 4-18.
Based on a jitter-free source
7
Differential CML compatible inputs
6
ORIGINATOR:
PNSPO!
B. Peters
P1TX6A-SX51-01M Product Specification Sheet
CONFIDENTIAL INFORMATION
DATE:
8/7/09
DOCUMENT NO.
DOC000924
SHEET 4 OF 10
D
PNSPO
®
OMRON NETWORK PRODUCTS
7.0
HDMI™ Signal Parameters
HDMI™ Signal Parameter 8 Symbol
Min
Typ
Max
Units
HDMI™ Input Signal – SCLIH,SDAIH
VIH
3.5
5.75
V
HDMI™ Input Signal – SCLIL,SDAIL
VIL
-0.5
1.5
V
Hot Plug Detect High
HPDH
2.4
5.3
V
Hot Plug Detect Low
HPDL
0
0.4
V
CEC Output Voltage Logic ‘0’
VCEC0
0
0.6
V
CEC Output Voltage Logic ‘1’
High to Low Input Voltage Threshold
Logic ‘0’
Low to High Input Voltage Threshold
Logic ‘1’
VCEC1
2.5
3.63
V
VCECT0
0.0
0.8
V
VCECT1
2.0
3.63
V
CEC Rise Time (10% to 90%)
tCECRise
250
μs
CEC Fall Time
tCECFall
50
μs
9
Status Signal Functional Table 10
8.0
Condition
Source
Cable
Source
Status
Sink
Cable
Status Signal Pin Output
Sink
Status
Optical
Cable
SS 1
SS 2
SS 3
SS 4
X
X
X
X
D
T
0
0
0
C
ON
C
ON
C
0
0
0
0
C
OFF
C
ON
C
0
0
0
1
C
X
D
X
C
0
0
1
1
C
X
C
OFF
C
0
0
1
1
D
X
X
X
C
0
1
1
1
X
D
C
T
0
1
Does Not Affect Output
Disconnected
Connected
Toggles Between 0 and 1 at ~ 10Hz
0 Volts
5 Volts
8
Reference I2C-Bus Specification v2 and HDMI™ rev 1.3a. Supports up to 100kHz bus speed.
The firmware version installed in the module must be version 2.10.06 or higher for CEC functionality. Update to version 2.10.06 or
higher if the current version is not at this revision level. Refer to P1_X6-SX51-01M Bootloader Manual for updating details.
10
Status signal table represents typical output. Variances in status signals may occur between different manufacturers and/or models
of sources and sinks.
9
ORIGINATOR:
PNSPO!
B. Peters
P1TX6A-SX51-01M Product Specification Sheet
CONFIDENTIAL INFORMATION
DATE:
8/7/09
DOCUMENT NO.
DOC000924
SHEET 5 OF 10
D
PNSPO
®
OMRON NETWORK PRODUCTS
9.0
Fiber Transmission Distance
Data Rate
1.65
Gbps
3.50
Gbps
Skew
Limit
OM1
(160 MHz*km)
OM2
(500 MHz*km)
OM3
(1000 MHz*km)
Units
None
200
400
1000
m
2.42ns
200
400
400
m
None
100
200
500
m
2.42ns
100
200
400
m
10.0 Laser Safety
The P1TX6-SX51-01 meets Class-3R requirements.
and handling practices per ANSI Z136.
Use proper eye protection
11.0 Firmware 11
The firmware utilized with the P1TX6-SX51-01M has been evaluated through the
following functional tests:
11.1 HDCP Compliance Test (Source)
1A-01 through 1A-09, 1B-01 through 1B-06
11.2 HDCP Compliance Test (Sink)
2C-01 through 2C-04
11.3 HDCP Compliance Test (Repeater)
3C-I-01 through 3C-I-07, 3C-II-01 through 3C-II-09, 3A-01 through 3A-05, 3B-01 through
3B-05
11.4 EDID for HDMI™ Compliance Test (Display sink devices)
8-1, 8-2, 8-3, 8-17, 8-18, 8-19
11.5 CEC Compliance Tests
7-1, 7-2, 8.1, 8.2, 9.1 through 9.5, 9.7-1, 10.1.1.1-1, 10.1.2, 10.2.3, 11.1.2-2, 11.1.3-2,
11.1.6-1 through 11.1.6-4, 11.2.1-1, 11.2.2-2, 11.2.2-3, 11.2.3-2, 11.2.6-1, 11.2.6-2,
11.2.7-3 through 11.2.7-6, 11.2.7-12, 11.2.7-13, 11.2.14-1, 12-1 through 12-3
12.0 Connectivity
The P1TX6-SX51-01M will support up to eight Key Selection Vectors (KSV)
allowing for up to eight HDCP compliant devices to be connected downstream
from the SX51-01M link.
11
Firmware is not warranted for interoperability with all HDMITM sources and sinks.
ORIGINATOR:
PNSPO!
B. Peters
P1TX6A-SX51-01M Product Specification Sheet
CONFIDENTIAL INFORMATION
DATE:
8/7/09
DOCUMENT NO.
DOC000924
SHEET 6 OF 10
D
PNSPO
®
OMRON NETWORK PRODUCTS
13.0 Patents
This product contains the following patents or patents pending: 6201908,
6396978, 6456757, 6558046, 6572278, 6652161.
ORIGINATOR:
PNSPO!
B. Peters
P1TX6A-SX51-01M Product Specification Sheet
CONFIDENTIAL INFORMATION
DATE:
8/7/09
DOCUMENT NO.
DOC000924
SHEET 7 OF 10
D
PNSPO
®
OMRON NETWORK PRODUCTS
14.0 TOSA Module Pin Numbers and Descriptions
The SX51 TX Module utilizes a 40 pin plug-down connector. Recommended
mounting position is on the top of the board and secured in place with mounting
screws located along the bottom face of the module enclosure. For information
on the specifications of the connector, contact Hirose (DF12 (5.0)-40DP-0.5V).
ORIGINATOR:
PNSPO!
Pin #
Name
Description
1
TMDS 2 +
Positive differential TMDS 2 signal (850nm)
2
VCC1
+3.3V Power Supply
3
GND
Ground
4
VCC1
+3.3V Power Supply
5
TMDS 2 -
Negative differential TMDS 2 signal (850nm)
6
Reserved
Reserved for Omron future use – Do Not Connect
7
TMDS 1 +
Positive differential TMDS 1 signal (825nm)
8
Reserved
Reserved for Omron future use – Do Not Connect
9
GND
Ground
10
Reserved
Reserved for Omron future use – Do Not Connect
11
TMDS 1 -
Negative differential TMDS 1 signal (825nm)
12
Reserved
Reserved for Omron future use – Do Not Connect
13
TMDS 0 +
Positive differential TMDS 0 signal (800nm)
14
SS 1
Fiber Connect Status Signal
15
GND
Ground
16
SS 2
5V Source Status Signal
17
TMDS 0 -
Negative differential TMDS 0 signal (800nm)
18
SS 3
Hot Plug Sink Status Signal
19
CLK +
Positive differential CLK signal (778nm)
20
SS 4
Video Detect Status Signal
B. Peters
P1TX6A-SX51-01M Product Specification Sheet
CONFIDENTIAL INFORMATION
DATE:
8/7/09
DOCUMENT NO.
DOC000924
SHEET 8 OF 10
D
PNSPO
®
OMRON NETWORK PRODUCTS
TOSA Module Pin Numbers and Descriptions (Cont’d)
Pin #
Name
Description
21
GND
22
NC
Ground
23
CLK -
Negative differential CLK signal (778nm)
24
NC
Do Not Connect
25
SRC_CEC
26
NC
12
Do Not Connect
Source CEC
13
Do Not Connect
27
NC
Do Not Connect
28
Reserved
Reserved for Omron future use
29
SRC_SCL
30
NC
Do Not Connect
31
SRC_SDA
Source Data
32
NC
Do Not Connect
33
GND
Source Clock
14
Ground
Module Reset
14
34
Reset
(Must be asserted to +5V for normal operation)
35
SRC_5V
36
VCC2
+5V Power Supply
37
SRC_HPD
Source Hot Plug Detect signal
38
VCC2
+5V Power Supply
39
GND
Ground
40
GND
Ground
Source 5V signal
15
12
NC = Do not connect this pin
Internal 27.4kΩ pull-up to 3.3v
14
Internal 47kΩ pull-up to 5v
14
See Information Package for Mechanical Reset Circuit
15
Internal 10kΩ pull-down to ground
13
ORIGINATOR:
PNSPO!
B. Peters
P1TX6A-SX51-01M Product Specification Sheet
CONFIDENTIAL INFORMATION
DATE:
8/7/09
DOCUMENT NO.
DOC000924
SHEET 9 OF 10
D
PNSPO
®
OMRON NETWORK PRODUCTS
15.0 Dimensions
The SX51 TX Module is designed to work with a standard SC ferrule only.
Insertion of any other type may result in damage. For dust cap information,
contact L-Com (DSTCP-SC).
Dimensions and orientation are for reference only.
**Temperature measurement point
All dimensions are in mm.
ORIGINATOR:
PNSPO!
B. Peters
P1TX6A-SX51-01M Product Specification Sheet
CONFIDENTIAL INFORMATION
DATE:
8/7/09
DOCUMENT NO.
DOC000924
SHEET 10 OF 10
D