DS3658 Quad High Current Peripheral Driver General Description The DS3658 quad peripheral driver is designed for those applications where low operating power, high breakdown voltage, high output current and low output ON voltage are required. A unique input circuit combines TTL compatibility with high impedance. In fact, its extreme low input current allows it to be driven directly by a CMOS device. The outputs are capable of sinking 600 mA each and offer a 70V breakdown. However, for inductive loads the output should be clamped to 35V or less to avoid latch-up during turn off (inductive fly back protectionÐrefer AN-213). An onchip clamp diode capable of handling 800 mA is provided at each output for this purpose. In addition, the DS3658 incorporates circuitry that guarantees glitch-free power up or down operation and a fail-safe feature which puts the output in a high impedance state when the input is open. The molded package is specifically constructed to allow increased power dissipation over conventional packages. The four ground pins are directly connected to the device chip with a special copper lead frame. When the quad driver is soldered into a PC board, the power rating of the device improves significantly. Y Y Y Y Features Y Y Y Y Y Y Y Y Y Y Y Y Applications Y Y Y Y Y Y Y Relay drivers Lamp drivers Solenoid drivers Hammer drivers Stepping motor drivers Triac drivers Y Y Y Y Connection Diagram LED drivers High current, high voltage drivers Level translators Fiber optic LED drivers Single saturated transistor outputs Low standby power, 10 mW typical High impedance TTL compatible inputs Outputs may be tied together for increased current capacity High output current 600 mA per output 2.4A per package No output latch-up at 35V Low output ON voltage (350 mV typ @ 600 mA) High breakdown voltage (70V) Open collector outputs Output clamp diodes for inductive fly back protection NPN inputs for minimal input currents (1 mA typical) Low operating power Standard 5V power supply Power up/down protection Fail safe operation 2W power package Pin-for-pin compatible with SN75437 Truth Table Dual-In-Line Package IN EN OUT H L H L H H L L L Z Z Z H e High state L e Low state Z e High impedance state TL/F/5819 – 1 Top View Order Number DS3658N See NS Package Number N16E C1995 National Semiconductor Corporation TL/F/5819 RRD-B30M105/Printed in U. S. A. DS3658 Quad High Current Peripheral Driver March 1995 Absolute Maximum Ratings (Note 1) Operating Conditions If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/Distributors for availability and specifications. Supply Voltage Ambient Temperature Supply Voltage Input Voltage Output Voltage Output Current Continuous Power Dissipation @ 25§ C Free-Air (Note 5) Storage Temperature Range Lead Temperature (Soldering, 4 sec.) Min 4.75 0 Max 5.25 70 Units V §C 7V 15V 70V 1.5A 2075 mW b 65§ C to a 150§ C 260§ C Electrical Characteristics (Notes 2 and 3) Symbol Parameter Conditions Min VIH Input High Voltage VIL Input Low Voltage IIH Input High Current VIN e 5.25V, VCC e 5.25V IIL Input Low Current VIN e 0.4V VIK Input Clamp Voltage II e b12 mA VOL Output Low Voltage Typ Max Units 0.8 V 2.0 V 10 mA g 10 mA b 0.8 b 1.5 V IL e 300 mA 0.2 0.4 V IL e 600 mA (Note 4) 0.35 0.7 V 100 mA ICEX Output Leakage Current VCE e 70V, VIN e 0.8V VF Diode Forward Voltage IF e 800 mA IR Diode Leakage Current VR e 70V ICC Supply Current 1.0 1.0 1.6 V 100 mA All Inputs High 60 85 mA All Inputs Low 2 4 mA Switching Characteristics (Note 2) Parameter Conditions Typ Max Units tPHL Symbol Turn On Delay RL e 60X, VL e 30V Min 226 500 ns tPLH Turn Off Delay RL e 60X, VL e 30V 2430 8000 ns Note 1: ‘‘Absolute Maximum Ratings’’ are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the device should be operated at these limits. The table of ‘‘Electrical Characteristics’’ provides conditions for actual device operation. Note 2: Unless otherwise specified, min/max limits apply across the 0§ C to a 70§ C temperature range and the 4.75V to 5.25V power supply range. All typical values are for TA e 25§ C and VCC e 5.0V. Note 3: All currents into device pins are shown as positive; all currents out of device pins are shown as negative; all voltages are referenced to ground, unless otherwise specified. All values shown as max or min are so classified on absolute value basis. Note 4: All sections of this quad circuit may conduct rated current simultaneously; however, power dissipation averaged over a short interval of time must fall within specified continuous dissipation ratings. Note 5: For operation over 25§ C free-air temperature, derate linearly to 1328 mW 2 @ 70§ C @ the rate of 16.6 mW/§ C. AC Test Circuit Switching Waveforms TL/F/5819 – 3 TL/F/5819 – 2 *Includes probe and jig capacitance Typical Applications Stepping Motor Driver Lamp Driver TL/F/5819 – 4 *L1, L2, L3, L4 are the windings of a bifilar stepping motor TL/F/5819 – 5 **VMOTOR is the supply voltage of the motor 3 DS3658 Quad High Current Peripheral Driver Physical Dimensions inches (millimeters) Molded Dual-In-Line Package (N) Order Number DS3658N NS Package Number N16E LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation 1111 West Bardin Road Arlington, TX 76017 Tel: 1(800) 272-9959 Fax: 1(800) 737-7018 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Europe Fax: (a49) 0-180-530 85 86 Email: cnjwge @ tevm2.nsc.com Deutsch Tel: (a49) 0-180-530 85 85 English Tel: (a49) 0-180-532 78 32 Fran3ais Tel: (a49) 0-180-532 93 58 Italiano Tel: (a49) 0-180-534 16 80 National Semiconductor Hong Kong Ltd. 13th Floor, Straight Block, Ocean Centre, 5 Canton Rd. Tsimshatsui, Kowloon Hong Kong Tel: (852) 2737-1600 Fax: (852) 2736-9960 National Semiconductor Japan Ltd. Tel: 81-043-299-2309 Fax: 81-043-299-2408 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.