TL082 Wide Bandwidth Dual JFET Input Operational Amplifier General Description Features These devices are low cost, high speed, dual JFET input operational amplifiers with an internally trimmed input offset voltage (BI-FET II™ technology). They require low supply current yet maintain a large gain bandwidth product and fast slew rate. In addition, well matched high voltage JFET input devices provide very low input bias and offset currents. The TL082 is pin compatible with the standard LM1558 allowing designers to immediately upgrade the overall performance of existing LM1558 and most LM358 designs. These amplifiers may be used in applications such as high speed integrators, fast D/A converters, sample and hold circuits and many other circuits requiring low input offset voltage, low input bias current, high input impedance, high slew rate and wide bandwidth. The devices also exhibit low noise and offset voltage drift. n n n n n n n n n Typical Connection Connection Diagram Internally trimmed offset voltage: 15 mV Low input bias current: 50 pA Low input noise voltage: 16nV/√Hz Low input noise current: 0.01 pA/√Hz Wide gain bandwidth: 4 MHz High slew rate: 13 V/µs Low supply current: 3.6 mA High input impedance: 1012Ω Low total harmonic distortion AV = 10,: < 0.02% RL = 10k, VO = 20 Vp − p, BW = 20 Hz−20 kHz n Low 1/f noise corner: 50 Hz n Fast settling time to 0.01%: 2 µs DIP/SO Package (Top View) DS008357-3 DS008357-1 Order Number TL082CM or TL082CP See NS Package Number M08A or N08E Simplified Schematic DS008357-2 BI-FET II™ is a trademark of National Semiconductor Corp. © 1999 National Semiconductor Corporation DS008357 www.national.com TL082 Wide Bandwidth Dual JFET Input Operational Amplifier April 1998 Absolute Maximum Ratings (Note 1) Input Voltage Range (Note 3) Output Short Circuit Duration Storage Temperature Range Lead Temp. (Soldering, 10 seconds) ESD rating to be determined. If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage Power Dissipation Operating Temperature Range Tj(MAX) Differential Input Voltage ± 18V (Note 2) 0˚C to +70˚C 150˚C ± 30V DC Electrical Characteristics Symbol ± 15V Continuous −65˚C to +150˚C 260˚C Note 1: “Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. (Note 5) Parameter Conditions TL082C Min Units Typ Max 5 15 Input Offset Voltage RS = 10 kΩ, TA = 25˚C Average TC of Input Offset Over Temperature RS = 10 kΩ 10 Input Offset Current Tj = 25˚C, (Notes 5, 6) 25 IB Input Bias Current Tj ≤ 70˚C Tj = 25˚C, (Notes 5, 6) RIN Input Resistance Tj ≤ 70˚C Tj = 25˚C AVOL Large Signal Voltage Gain VO Output Voltage Swing VCM Input Common-Mode Voltage −12 V CMRR Common-Mode Rejection Ratio RS ≤ 10 kΩ 70 100 dB PSRR Supply Voltage Rejection Ratio (Note 7) 70 100 IS Supply Current VOS ∆VOS/∆T 20 mV mV µV/˚C Voltage IOS VS = ± 15V, TA = 25˚C VO = ± 10V, RL = 2 kΩ Over Temperature VS = ± 15V, RL = 10 kΩ VS = ± 15V 50 25 Symbol Conditions Amplifier to Amplifier Coupling TA = 25˚C, f = 1Hz20 kHz (Input Referred) VS = ± 15V, TA = 25˚C Slew Rate Gain Bandwidth Product en in pA 8 nA Ω 100 V/mV V/mV ± 13.5 V +15 V dB 5.6 mA (Note 5) TL082C Min SR nA 400 1012 3.6 Parameter GBW pA 4 15 ± 12 ± 11 Range AC Electrical Characteristics 200 Equivalent Input Noise Voltage VS = ± 15V, TA = 25˚C TA = 25˚C, RS = 100Ω, f = 1000 Hz Equivalent Input Noise Current Tj = 25˚C, f = 1000 Hz Typ −120 8 Units Max dB 13 V/µs 4 MHz 25 nV/√Hz 0.01 pA/√Hz Note 2: For operating at elevated temperature, the device must be derated based on a thermal resistance of 115˚C/W junction to ambient for the N package. Note 3: Unless otherwise specified the absolute maximum negative input voltage is equal to the negative power supply voltage. Note 4: The power dissipation limit, however, cannot be exceeded. Note 5: These specifications apply for VS = ± 15V and 0˚C ≤TA ≤ +70˚C. VOS, IB and IOS are measured at VCM = 0. Note 6: The input bias currents are junction leakage currents which approximately double for every 10˚C increase in the junction temperature, Tj. Due to the limited production test time, the input bias currents measured are correlated to junction temperature. In normal operation the junction temperature rises above the ambient temperature as a result of internal power dissipation, PD. Tj = TA + θjA PD where θjA is the thermal resistance from junction to ambient. Use of a heat sink is recommended if input bias current is to be kept to a minimum. Note 7: Supply voltage rejection ratio is measured for both supply magnitudes increasing or decreasing simultaneously in accordance with common practice. VS = ± 6V to ± 15V. www.national.com 2 Typical Performance Characteristics Input Bias Current Input Bias Current DS008357-19 DS008357-18 Positive Common-Mode Input Voltage Limit Supply Current Negative Common-Mode Input Voltage Limit DS008357-20 Positive Current Limit DS008357-23 DS008357-21 Negative Current Limit DS008357-22 Voltage Swing Output Voltage Swing DS008357-25 DS008357-24 3 DS008357-26 www.national.com Typical Performance Characteristics Gain Bandwidth (Continued) Bode Plot Slew Rate Distortion vs Frequency DS008357-29 DS008357-28 DS008357-27 Undistorted Output Voltage Swing Open Loop Frequency Response DS008357-30 DS008357-31 Common-Mode Rejection Ratio Power Supply Rejection Ratio DS008357-33 DS008357-32 Equivalent Input Noise Voltage DS008357-34 DS008357-35 www.national.com 4 Typical Performance Characteristics Open Loop Voltage Gain (V/V) (Continued) Output Impedance Inverter Setting Time DS008357-37 DS008357-38 DS008357-36 Pulse Response Small Signal Inverting Small Signal Non-Inverting DS008357-7 DS008357-6 Large Signal Inverting Large Signal Non-Inverting DS008357-8 DS008357-9 5 www.national.com Pulse Response (Continued) Current Limit (RL = 100Ω) DS008357-10 The amplifiers will drive a 2 kΩ load resistance to ± 10V over the full temperature range of 0˚C to +70˚C. If the amplifier is forced to drive heavier load currents, however, an increase in input offset voltage may occur on the negative voltage swing and finally reach an active current limit on both positive and negative swings. Precautions should be taken to ensure that the power supply for the integrated circuit never becomes reversed in polarity or that the unit is not inadvertently installed backwards in a socket as an unlimited current surge through the resulting forward diode within the IC could cause fusing of the internal conductors and result in a destroyed unit. Because these amplifiers are JFET rather than MOSFET input op amps they do not require special handling. As with most amplifiers, care should be taken with lead dress, component placement and supply decoupling in order to ensure stability. For example, resistors from the output to an input should be placed with the body close to the input to minimize “pick-up” and maximize the frequency of the feedback pole by minimizing the capacitance from the input to ground. A feedback pole is created when the feedback around any amplifier is resistive. The parallel resistance and capacitance from the input of the device (usually the inverting input) to AC ground set the frequency of the pole. In many instances the frequency of this pole is much greater than the expected 3 dB frequency of the closed loop gain and consequently there is negligible effect on stability margin. However, if the feedback pole is less than approximately 6 times the expected 3 dB frequency a lead capacitor should be placed from the output to the input of the op amp. The value of the added capacitor should be such that the RC time constant of this capacitor and the resistance it parallels is greater than or equal to the original feedback pole time constant. Application Hints These devices are op amps with an internally trimmed input offset voltage and JFET input devices (BI-FET II). These JFETs have large reverse breakdown voltages from gate to source and drain eliminating the need for clamps across the inputs. Therefore, large differential input voltages can easily be accommodated without a large increase in input current. The maximum differential input voltage is independent of the supply voltages. However, neither of the input voltages should be allowed to exceed the negative supply as this will cause large currents to flow which can result in a destroyed unit. Exceeding the negative common-mode limit on either input will cause a reversal of the phase to the output and force the amplifier output to the corresponding high or low state. Exceeding the negative common-mode limit on both inputs will force the amplifier output to a high state. In neither case does a latch occur since raising the input back within the common-mode range again puts the input stage and thus the amplifier in a normal operating mode. Exceeding the positive common-mode limit on a single input will not change the phase of the output; however, if both inputs exceed the limit, the output of the amplifier will be forced to a high state. The amplifiers will operate with a common-mode input voltage equal to the positive supply; however, the gain bandwidth and slew rate may be decreased in this condition. When the negative common-mode voltage swings to within 3V of the negative supply, an increase in input offset voltage may occur. Each amplifier is individually biased by a zener reference which allows normal circuit operation on ± 6V power supplies. Supply voltages less than these may result in lower gain bandwidth and slew rate. www.national.com 6 Detailed Schematic DS008357-11 Typical Applications Three-Band Active Tone Control DS008357-12 7 www.national.com Typical Applications (Continued) DS008357-13 • All potentiometers are linear taper • Use the LF347 Quad for stereo applications Note 8: All controls flat. Note 9: Bass and treble boost, mid flat. Note 10: Bass and treble cut, mid flat. Note 11: Mid boost, bass and treble flat. Note 12: Mid cut, bass and treble flat. Improved CMRR Instrumentation Amplifier DS008357-14 C and E are separate isolated grounds Matching of R2’s, R4’s and R5’s control CMRR With AVT = 1400, resistor matching = 0.01%: CMRR = 136 dB • Very high input impedance • Super high CMRR www.national.com 8 Typical Applications (Continued) Fourth Order Low Pass Butterworth Filter DS008357-15 Fourth Order High Pass Butterworth Filter DS008357-16 9 www.national.com Typical Applications (Continued) Ohms to Volts Converter DS008357-17 www.national.com 10 Physical Dimensions inches (millimeters) unless otherwise noted Order Number TL082CM NS Package M08A Order Number TL082CP NS Package N08E 11 www.national.com TL082 Wide Bandwidth Dual JFET Input Operational Amplifier Notes LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: [email protected] www.national.com National Semiconductor Europe Fax: +49 (0) 1 80-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 1 80-530 85 85 English Tel: +49 (0) 1 80-532 78 32 Français Tel: +49 (0) 1 80-532 93 58 Italiano Tel: +49 (0) 1 80-534 16 80 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: [email protected] National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.