HEC75 SERIES 75 WATTS DC-DC CONVERTER FEATURES • 75 WATTS MAXIMUM OUTPUT POWER • SINGLE : OUTPUT CURRENT UP TO 20A DUAL : TOTAL OUTPUT CURRENT UP TO 15A, UP TO 100% LOAD IMBALANCE • COMPACT 2.40 X 2.28 X 0.50 INCH PACKAGE • HIGH EFFICIENCY UP TO 90% • INPUT RANGE FROM 36VDC TO 75VDC • FIXED SWITCHING FREQENCY (300kHz) • HALT TESTED • INDUSTRY STANDARD FOOTPRINT • ADJUSTABLE OUTPUT VOLTAGE, INDEPENDENTLY REGULATED OUTPUTS • INPUT TO OUTPUT BASIC INSULATION:1600 VDC • CE MARK MEETS 2006/95/EC, 2011/95/EC AND 2004/108/EC • SAFETY MEETS UL60950-1, EN60950-1 AND IEC60950-1 • ISO9001 CERTIFIED MANUFACTURING FACILITIES • COMPLIANT TO RoHS EU DIRECTIVE 2011/65/EU APPLICATIONS Wireless Network Telecom/Datacom Industry Control System Distributed Power Architectures Semiconductor Equipment OPTIONS Positive remote on/off, pin length DESCRIPTION HEC75-SERIES DC/DC converters provide up to 75 watts of output power in an industry standard half-brick package and footprint. All models feature a wide input range, trimmable output voltage and a 20A current rating (15A for dual output). T E C H N I C A L S P E C I F I C AT I O N All specifications are typical at nominal input, full load and 25ºC otherwise noted OUTPUT SPECIFICATIONS INPUT SPECIFICATIONS Output power 75 Watts, max. Voltage accuracy ± 1.5% Minimum load 0% + 10%, -20% ± 10% See table Line regulation Single (Note 5) Dual LL to HL at FL Load regulation No Load to Full Load Remote sense Single (Note 5) Voltage adjustability Ripple and noise See table 10% of Vout(nom) 20MHz bandwidth (Note 6) 100mVp-p ±0.02% / ºC, max. Temperature coefficient Transient response recovery time 25% load step change 200µs Over voltage protection threshold 115% ~ 130% of Vout(nom) (Non-latching Hiccup) Maximum total output current I 1 + I 2 Dual 15A Over current protection threshold Short circuit protection 110% ~ 140% of Iout Rated Continuous, automatics recovery GENERAL SPECIFICATIONS Efficiency Isolation voltage Isolation resistance Input to Output Input(Output) to Case 500VDC See table 1600 VDC, min. 1minute 1000 VDC, min. 1minute 7 10 ohms, min. Isolation capacitance 2500pF, max. Switching frequency 300kHz±10% Design meets safety standard IEC60950-1, UL60950-1, EN60950-1 Case material Open with Aluminum base-plate Single 63g (2.22oz) Weight Dual 70g (2.47oz) BELLCORE TR-NWT-000332 Single 9.370 x 106 hrs Dual 1.300 x 105 hrs MTBF (Note 1) MIL-HDBK-217F Single 2.170 x 105 hrs Dual 1.080 x 105 hrs Page 1 of 3 Input voltage range 36 ~ 75VDC Input filter L-C type Input surge voltage Nominal input and Start up time constant resistive load Input reflected-ripple current 100VDC 100ms,max Power up 25ms Remote ON/OFF 25ms 20mAp-p Start-up voltage 34VDC Shutdown voltage Remote ON/OFF (Note 7) (Negative logic) 32VDC ON=Short or 0V < Vr < 1.2V, OFF=Open or 3V < Vr < 15V, ON=Open or 3V < Vr < 15V, OFF=Short or 0V < Vr < 1.2V, (Positive logic) Input current of remote control pin Remote off state input current Nominal input Nominal input IIN=1mA max. IIN=50µA max. IIN=50µA max. IIN=1mA max. -0.5mA ~ 0.5mA 20mA ENVIRONMENTAL SPECIFICATIONS Operating base-plate temperature range (Note 8) -40ºC ~ +100ºC Over temperature protection +110ºC Humidity max, Non-condensing 95% Storage temperature range -55ºC ~ +125ºC Thermal shock MIL-STD-810F Vibration MIL-STD-810F EMC CHARACTERISTICS EMI (Note 9) EN55022 Radiated immunity EN61000-4-3 10 V/m Perf. Criteria A Fast transient (Note 10) EN61000-4-4 ± 2kV Perf. Criteria B Surge (Note 10) EN61000-4-5 ± 1kV Perf. Criteria B Conducted immunity EN61000-4-6 10 Vr.m.s Perf. Criteria A www.pduke.com Class A, Class B 2013/5/3 HEC75 SERIES 75 WATTS Output Current DC-DC CONVERTER (3) (4) Line Regulation Load Regulation No load Input Current 20 A 4 mV 6 mV 120mA 85 0mA 20 A 5 mV 8 mV 90mA 87 3.3 VDC 0mA 20 A 7 mV 10 mV 120mA 90 36 ~ 75 VDC 5.0 VDC 0mA 15 A 10 mV 15 mV 130mA 90 36 ~ 75 VDC 15 VDC 0mA 5A 30 mV 45 mV 160mA 90 Model Number Input Range Output Voltage HEC75~48S1P8 36 ~ 75 VDC 1.8 VDC 0mA HEC75~48S2P5 36 ~ 75 VDC 2.5 VDC HEC75~48S3P3 36 ~ 75 VDC HEC75~48S05 HEC75~48S15 Model Number Input Range Min. load Full load Output Voltage Output Current V1 V2 I1 I2 Eff (%) (4) Line Regulation Load Regulation Eff (%) HEC75-48D3305 36 ~ 75 VDC 5 VDC 3.3 VDC 15 A 15 A 10/7 mV 15/10 mV 88 HEC75-48D3325 36 ~ 75 VDC 3.3 VDC 2.5 VDC 15 A 15 A 7/5 mV 10/8 mV 81 HEC75-48D0518 36 ~ 75 VDC 5 VDC 1.8 VDC 15 A 15 A 10/4 mV 15/6 mV 85 HEC75-48D3318 36 ~ 75 VDC 3.3 VDC 1.8 VDC 15 A 15 A 7/4 mV 10/6 mV 81 Note 1. BELLCORE TR-NWT-000332. Case 1: 50% Stress, Temperature at Tc=40ºC. MIL-HDBK-217F Notice2 @Ta=25 ºC, Full load(Ground, Benign, controlled environment). 2. The converter is provided by basic insulation. 3. Typical value at nominal input voltage and no load. 4. Single：Typical value at nominal input voltage and full load. Dual：Typical value at nominal input voltage and both outputs current are 7.5A. 5. Maximum output deviation is 10% inclusive of remote sense. If remote sense is not being used, the + SENSE should be connected to its corresponding +OUTPUT and likewise the -SENSE should be connected to its corresponding –OUTPUT. 6. Measured with a 1µF M/C and a 10µF M/C(for dual outputs) or 1µF M/C and a 10µF T/C(for single outputs) 7. The negative / positive logic and pin length are optional. The pin voltage is referenced to –INPUT Single：Please see single output product options table. Dual：Please see dual output product options table. 8. Heat-sink is optional and P/N: 7G-0021A-F, 7G-0022A-F, 7G-0023A-F, 7G-0024A-F. 9. The HEC75 series standard module meets EN55022 Class A and Class B with external components. For more detail information, please contact with P-DUKE. 10. An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5. The filter capacitor Power Mate suggest: Nippon chemi-con KY series, 220µF/100V. 11. CASE GROUNDING：When connect the case pin and four screw bolts to shield plane, the EMI could be reduced. CAUTION: This power module is not internally fused. An input line fuse must always be used. Page 2 of 3 www.pduke.com 2013/5/3 HEC75 SERIES MECHANICAL DRAWING SINGLE OUTPUT: 75 WATTS ： DC-DC CONVERTER PIN CONNECTION PIN 1 2 3 4 5 6 7 8 9 (Note 11) DEFINE -INPUT CASE CTRL +INPUT -OUTPUT -SENSE TRIM +SENSE +OUTPUT DIAMETER 0.040 Inch（1.02mm） 0.040 Inch（1.02mm） 0.040 Inch（1.02mm） 0.040 Inch（1.02mm） 0.080 Inch（2.03mm） 0.040 Inch（1.02mm） 0.040 Inch（1.02mm） 0.040 Inch（1.02mm） 0.080 Inch（2.03mm） EXTERNAL OUTPUT TRIMMING Output can be externally trimmed by using the method shown below. TRIM UP TRIM DOWN 7 1. All dimensions in Inch (mm) Tolerance: X.XX±0.02 (X.X±0.5) X.XXX±0.01 (X.XX±0.25) 2. Pin pitch tolerance ±0.01(0.25) 3. Pin dimension tolerance ±0.004 (0.1) Remote On/Off and Pin Options Negative remote ON/OFF logic, 0.200” pin length (standard) Negative remote ON/OFF logic, 0.145” pin length Positive remote ON/OFF logic, 0.200” pin length Positive remote ON/OFF logic, 0.145” pin length 6 RU 8 Suffix -L -P -S Example：HEC75-48S3P3-PHS * The module can’t equip heat-sink with TH option. DUAL OUTPUT: RD 7 Heat-Sink and Mounting Hole Tread Options Without heat-sink 7G-0021A-F 7G-0022A-F 7G-0023A-F 7G-0024A-F Through hole (No thread) Suffix -HS -HS1 -HS2 -HS3 -TH PIN CONNECTION PIN 1 2 3 4 5 6 7 8 9 10 (Note 11) DEFINE -INPUT CASE CTRL +INPUT +V2 -V2 (COM) V2 TRIM +V1 -V1 (COM) V1 TRIM DIAMETER 0.040 Inch（1.02mm） 0.040 Inch（1.02mm） 0.040 Inch（1.02mm） 0.040 Inch（1.02mm） 0.040 Inch（1.02mm） 0.040 Inch（1.02mm） 0.040 Inch（1.02mm） 0.040 Inch（1.02mm） 0.040 Inch（1.02mm） 0.040 Inch（1.02mm） EXTERNAL OUTPUT TRIMMING Output can be externally trimmed by using the method shown below. ( ) for V2 output trim TRIM UP 1. All dimensions in Inch (mm) Tolerance: X.XX±0.02 (X.X±0.5) X.XXX±0.01 (X.XX±0.25) 2. Pin pitch tolerance ±0.01(0.25) 3. Pin dimension tolerance ±0.004 (0.1) Remote On/Off and Pin Options Negative remote ON/OFF logic, 0.200” pin length (standard) Negative remote ON/OFF logic, 0.145” pin length Negative remote ON/OFF logic, 0.200” pin length Positive remote ON/OFF logic, 0.145” pin length 9（6） 10（7） RU 10（7） Suffix -L -N -S Example：HEC75-48D3305-PHS * The module can’t equip heat-sink with TH option. Page 3 of 3 TRIM DOWN www.pduke.com RD 8（5） Heat-Sink and Mounting Hole Tread Options Without heat-sink 7G-0021A-F 7G-0022A-F 7G-0023A-F 7G-0024A-F Through hole (No thread) Suffix -HS -HS1 -HS2 -HS3 -TH 2013/5/3