LED15 SERIES - RSG Electronic Components GmbH

LED15 SERIES
15 WATTS
DC-DC CONVERTER
FEATURES
• 15 WATTS MAXIMUM OUTPUT POWER
• SINGLE OUTPUT UP TO 3.5A
• SMALL SIZE AND LOW PROFILE 1.10 x 0.94 x 0.34 INCH
• HIGH EFFICIENCY UP TO 88%
• 2:1 WIDE INPUT VOLTAGE RANGE
• FIXED SWITCHING FREQUENCY
• INPUT TO OUTPUT ISOLATION: 2250VDC
• INDUSTRY STANDARD PIN-OUT FEC15 SERIES COMPATIBLE
• SURFACE-MOUNT OR THROUGH-HOLE
• SMD PACKAGE QUALIFIED FOR LEADFREE REFLOW SOLDER
:
PROCESS ACCORDING IPC J-STD-020D
• COST EFFICIENT OPEN FRAME DESIGN
• -40 to +85 WIDE OPERATING TEMPERATURE
• CE MARK MEETS 2006/95/EC, 2011/95/EC AND 2004/108/EC
• SAFETY MEETS UL60950-1, EN60950-1 AND IEC60950-1
• ISO9001 CERTIFIED MANUFACTURING FACILITIES
• COMPLIANT TO RoHS EU DIRECTIVE 2011/65/EU
OPTIONS
℃
APPLICATIONS
Wireless Network
Telecom/Datacom
Industry Control System
Measurement Equipment
Semiconductor Equipment
Positive logic Remote On/Off, SMD type, Without TRIM pin, Without CTRL pin
DESCRIPTION
LED15 single output DC/DC converters provide up to 15 watts of output power in an
industry standard package and footprint. All models feature a wide input range,
comprehensively protected against over-current, over-voltage and input
under-voltage protection conditions, and trimmable output voltage.
T E C H N I C A L S P E C I F I C AT I O N
All specifications are typical at nominal input, full load and 25ºC otherwise noted
INPUT SPECIFICATIONS
OUTPUT SPECIFICATIONS
Output power
15Watts max
Voltage accuracy
±1%
Minimum load
0%
Voltage adjustability (Note 6)
Line regulation
Load regulation
Ripple and noise
±10%
LL to HL at Full Load
±0.2%
No Load to Full Load
20MHz bandwidth
(Measured with a 1µF M/C and a 10µF T/C)
±0.2%
See table
±0.02%/ºC, max.
Temperature coefficient
Transient response recovery time
25% load step change
ΔIo/Δt=0.1A/us
3.3VDC output
5VDC output
12VDC output
15VDC output
Over voltage protection
(Voltage clamped)
300µs
3.7VDC~5.4VDC
5.6VDC~7.0VDC
13.5VDC~19.6VDC
16.8VDC~20.5VDC
Output load protection
150%, max.
Short circuit protection
Continuous, automatics recovery
Output voltage overshoot
3%
GENERAL SPECIFICATIONS
Efficiency
See table
Isolation voltage
Input to Output
Isolation resistance
500VDC
2250 VDC, min. 1minute
Isolation capacitance
5VDC,3.3VDC
15VDC,12VDC
Switching frequency
Design meets safety standard
Dimensions
Weight
MTBF (Note 1)
Page 1 of 3
℃
.
24VDC nominal input
18 ~ 36VDC
48VDC nominal input
36 ~ 75VDC
24VDC input
50VDC 100ms, max.
Input surge voltage
48VDC input
100VDC 100ms, max.
12uH source impedance
Input reflected ripple current
30mAp-p
( filter with 220µF & 33µF)
Nominal input and
Power up
30ms, max.
Start up time
Constant resistive load Remote ON/OFF
30ms, max.
18VDC, max.
24VDC input
Start-up voltage
36VDC, max.
48VDC input
14.5VDC
24VDC input
Shutdown voltage
30.5VDC
48VDC input
Remote ON/OFF (Note 7)
Positive logic(Option)
DC-DC ON
Open or 3V < Vr < 15V
DC-DC OFF
Short or 0V < Vr < 1.2V
Negative logic(Standard)
DC-DC ON
Short or 0V < Vr < 1.2V
DC-DC OFF
Open or 3V < Vr < 15V
Input current of remote control pin Nominal input
-0.5mA ~ 1.0mA
Remote off state input current
Nominal input
20mA,Max
Input voltage range
π
ENVIRONMENTAL SPECIFICATIONS
Operating ambient temperature (Note 8)
-40ºC ~ +85ºC (with derating)
Storage temperature range
-55 ºC ~ +125 ºC
Thermal shock
MIL-STD-810F
Vibration
MIL-STD-810F
Relative humidity
5% to 95% RH
10MΩ, min
Lead-free reflow solder process
IPC J-STD-020D
1000pF
Moisture sensitivity level(MSL)
IPC J-STD-033B level 2a
270kHz±10%
470kHz±10%
IEC60950-1,UL60950-1,EN60950-1
1.10 X 0.94 X 0.34 Inch
(27.9 X 23.9 X 8.5 mm)
10.5g(0.36oz)
BELLCORE TR-NWT-000332
2.200x106hrs
MIL-HDBK-217F
1.314x106hrs
EMC CHARACTERISTICS
EMI (Note 9)
EN55022
Radiated immunity
EN61000-4-3
Class A, Class B
10 V/m
Surge (Note 10)
EN61000-4-5
± 2kV
± 1kV
Conducted immunity
EN61000-4-6
10 Vr.m.s
Fast transient (Note 10) EN61000-4-4
www.pduke.com
Perf. Criteria A
Perf. Criteria B
Perf. Criteria A
Perf. Criteria A
2013/5/3
LED15 SERIES
15 WATTS
Model
Number
LED15-24S3P3
LED15-24S05
LED15-24S12
LED15-24S15
LED15-48S3P3
LED15-48S05
LED15-48S12
LED15-48S15
Input
Range
Output
Voltage
18 ~ 36 VDC
18 ~ 36 VDC
18 ~ 36 VDC
18 ~ 36 VDC
36 ~ 75 VDC
36 ~ 75 VDC
36 ~ 75 VDC
36 ~ 75 VDC
3.3 VDC
5 VDC
12 VDC
15 VDC
3.3 VDC
5 VDC
12 VDC
15 VDC
Output Current
Min. load Full Load
0mA
0mA
0mA
0mA
0mA
0mA
0mA
0mA
DC-DC CONVERTER
(2)
(3)
Output
Ripple & Noise
No load
Input Current
75mVp-p
75mVp-p
100mVp-p
100mVp-p
75mVp-p
75mVp-p
100mVp-p
100mVp-p
20mA
20mA
15mA
15mA
15mA
15mA
10mA
10mA
3500mA
3000mA
1250mA
1000mA
3500mA
3000mA
1250mA
1000mA
(4)
(5)
Eff
Capacitor
(%) Load max
86
87
87
88
85
87
87
88
10000µF
6000µF
1000µF
660µF
10000µF
6000µF
1000µF
660µF
Note
1. BELLCORE TR-NWT-000332. Case 1: 50% Stress, Temperature at 40ºC.
MIL-HDBK-217F Notice2 @Ta=25 ºC, Full load(Ground, Benign, controlled environment)
2. Typical value at nominal input and full load. (20MHz BW.)
3. Typical value at nominal input and no load.
4. Typical value at nominal input and full load.
5. Test by minimum input and constant resistive load.
6. Trimming allows the user to increase or decrease the output voltage set point of the module. This is accomplished by connecting an external resistor
between the TRIM pin and either the + OUTPUT pin or the - OUTPUT pin.
7. The CTRL pin voltage is reference to -INPUT. The order number please see product standard table.
8. The power module operate in a variety of thermal environments; however, sufficient cooling should be provided to help ensure reliable operation.
9. The LED15 series standard module meets EN55022 Class A and Class B with external components.
For more detail information, please contact with P-DUKE.
10. An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5.
The filter capacitor Power Mate suggest: Nippon chemi-con KY series, 220µF/100V.
CAUTION: This power module is not internally fused. An input line fuse must always be used.
LED15-48S05 Derating Curve
LED15-48S05 Efficiency VS Input Voltage
Page 2 of 3
LED15-48S05 Efficiency VS Output Current
www.pduke.com
2013/5/3
LED15 SERIES
15 WATTS
DC-DC CONVERTER
MECHANICAL DRAWING
DIP TYPE
SMD TYPE
1. All dimensions in Inch (mm)
Tolerance: X.XX±0.02 (X.X±0.5)
X.XXX±0.01 (X.XX±0.25)
2. Pin pitch tolerance ±0.01(0.25)
3. Pin dimension tolerance ±0.004 (0.1)
PIN CONNECTION
PIN
1
2
3
4
5
6
LED15W SERIES
+ INPUT
- INPUT
CTRL
+OUTPUT
TRIM
-OUTPUT
EXTERNAL OUTPUT TRIMMING
Output can be externally trimmed by using
the method shown below.
TRIM UP
TRIM DOWN
6
5
RU
RD
5
4
PRODUCT STANDARD TABLE
Option
Negative remote ON/OFF with DIP(Standard)
Negative remote ON/OFF with SMT
Positive remote ON/OFF with DIP
Positive remote ON/OFF with SMT
DIP type without CTRL pin
SMT type without CTRL pin
DIP type, negative remote ON/OFF without TRIM pin
SMT type, negative remote ON/OFF without TRIM pin
DIP type without CTRL&TRIM pin
SMT type without CTRL&TRIM pin
DIP type, positive remote ON/OFF without TRIM pin
SMT type, positive remote ON/OFF without TRIM pin
Page 3 of 3
www.pduke.com
Suffix
-A
-B
-C
-D
-E
-F
-G
-H
-I
-J
-K
2013/5/3