TVS P4FMAJ SERIES SURFACE MOUNT GPP TRANSIENT VOLTAGE SUPPRESSOR 400 WATT PEAK POWER 1.0 WATTS STEADY STATE FEATURES * * * * * * Plastic package has underwriters laboratory Glass passivated chip construction 400 watt surage capability at 1ms Excellent clamping capability Low zener impedance Fast response time DO-214AC 0.067 (1.70 ) 0.051 (1.29 ) 0.110 ( 2.79 ) 0.086 ( 2.18 ) 0.180 ( 4.57 ) 0.160 ( 4.06 ) 0.012 ( 0.305 ) 0.006 ( 0.152 ) 0.091 ( 2.31 ) 0.067 ( 1.70 ) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS 0.059 ( 1.50 ) 0.035 ( 0.89 ) 0.008 ( 0.203 ) 0.004 ( 0.102 ) Ratings at 25 o C ambient temperature unless otherwise specified. 0.209 ( 5.31 ) 0.185 ( 4.70 ) Single phase, half wave, 60 Hz, resistive or inductive load, For capacitive load, derate current by 20%. Dimensions in inches and (millimeters) MAXIMUM RATINGS (@ TA=25 OC unless otherwise noted) SYMBOL VALUE UNITS Peak Power Dissipation at TA = 25OC,TP = 1mS (Note 1) P PPM Minimum 400 W Peak Pulse Current with a 10/1000uS waveform ( Note 1, Fig.3 ) I PPM SEE TABLE 1 A P M(AV) 1.0 W I FSM 40 A VF 3.5/6.5 T J, T STG -55 to + 150 RATINGS Steady State Power Dissipation at TL = 75 C lead length, .375" (9.5 mm) (Note 2) O Peak Forward Surge Current, 8.3ms single half sine wavesuperimmposed on rated load ( JEDEC METHOD ) (Note 3) Maximum Instantaneous Forward Voltage @25A for unidirectional only ( Note 5 ) Operating and Storage Temperature Range o NOTES : 1. Non-repetitive current pulse, per Fig.3 and derated above TA = 25 C per Fig.2. 2. Mounted on 0.2 X 0.2” (5.0 X 5.0mm) copper pad to each terminal. 3. Measured on 8.3mS single half Sine-Wave or equivalent wave, duty cycle = 4 pulses per minute maximum. 4. "Fully ROHS compliant", "100% Sn plating (Pb-free)". 5. VF = 3.5V max. for devices of V(BR) < 200V and VF = 6.5V max. for devices of V(BR) > 200V. V 0 C 2013-01 REV: O RATING AND CHARACTERISTIC CURVES ( P4FMAJ6.8 THRU P4FMAJ400CA ) FIG. 1 - PEAK PULSE POWER RATING CURVE (IPP) DERATING IN PERCENTAGE,% Non-Repetitive Pulse Waveform Shown in Fig.3 TA = 25 1.0 0.2X0.2"(5.0X5.0mm) copper pad areas 0.1 0.1uS PEAK PULSE POWER (PPP) OR CURRENT PPPM, PEAK PULSE POWER, KW 100 10 FIG. 2 - PULSE DERATING CURVE 100 75 50 25 0 1.0uS 10uS 100uS 1.0mS 10mS 0 25 TP, PULSE WIDTH, sec 75 100 125 150 175 200 ) FIG. 4 - TYPICAL JUNCTION CAPACITANCE FIG. 3 - PULSE WAVEFORM 150 100000 tr = 10usec. Pulse Width (td) is Defined as the Point Where the Peak Current Decays to 50% of IPPM CJ, CAPACITANCE, pF IPPM, PEAK PULSE CURRENT,% 50 TA, AMBIENT TEMPERATURE,( Peak Value IPPM 100 IPPM HALF VALUE 2 10/1000usec. Waveform as Defined by R.E.A. 50 f = 1.0 MHz Vsig = 50mVp-p TJ = 25 10000 Measured at Zero Bias 1000 Measured at Devices Stand off Voltage,VWM 100 0 0 1.0 2.0 t, TIME,mS 3.0 4.0 1.0 10 100 200 V(BR), BREAKDOWN VOLTACE, VOLTS RECTRON RATING AND CHARACTERISTIC CURVES ( P4FMAJ6.8 THRU P4FMAJ400CA ) FIG. 6 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT UNIDIRECTIONAL 1.00 50 IFSM, PEAK FORWARD SURGE CURRENT AMPERES 60Hz Resistive or Inductive Load 0.75 0.50 0.25 0 8.3ms Single Half Sine-Wave (JEDED Method) TJ = TJ max. 40 30 20 10 0 0 25 50 75 100 125 150 TL, LEAD TEMPERATURE ( 175 200 1 ) 10 NUMBER OF CYCLES AT 60 Hz FIG. 7 -TYPICAL REVERSE LEAKAGE ID, INSTANTANEOUS REVERSE LEAKAGE CHRRENT, MICROAMPERES PM(AV), STEADY STATE POWER DISSIATION, WATTS FIG. 5 - STEADY STATE POWER DERATING CURVE CHARACTERISTICS 100 Measured at Devices Stand-off Voltage, VWM 10 1 TJ = 25 0.1 0.01 0 100 200 300 400 600 V(BR) BREAKDOWN VOLTAGE, VOLTS RECTRON 100 TRANSIENT VOLTAGE SUPPRESSORS 400W SERIES TVS DIODES / DO-214AC ( CASE 2 ) 400W TYPE P4FMAJ6.8 P4FMAJ6.8A P4FMAJ7.5 P4FMAJ7.5A P4FMAJ8.2 P4FMAJ8.2A P4FMAJ9.1 P4FMAJ9.1A P4FMAJ10 P4FMAJ10A P4FMAJ11 P4FMAJ11A P4FMAJ12 P4FMAJ12A P4FMAJ13 P4FMAJ13A P4FMAJ15 P4FMAJ15A P4FMAJ16 P4FMAJ16A P4FMAJ18 P4FMAJ18A P4FMAJ20 P4FMAJ20A P4FMAJ22 P4FMAJ22A P4FMAJ24 P4FMAJ24A P4FMAJ27 P4FMAJ27A P4FMAJ30 P4FMAJ30A P4FMAJ33 P4FMAJ33A P4FMAJ36 P4FMAJ36A P4FMAJ39 P4FMAJ39A P4FMAJ43 P4FMAJ43A P4FMAJ47 P4FMAJ47A P4FMAJ51 P4FMAJ51A P4FMAJ56 P4FMAJ56A Breakdown Voltage VBR @IT (Volts) MIN. MAX. (mA) Reverse Stand off Voltage VWM (Volts) 6.12 6.45 6.75 7.13 7.38 7.79 8.19 8.65 9.00 9.50 9.90 10.5 10.8 11.4 11.7 12.4 13.5 14.3 14.4 15.2 16.2 17.1 18.0 19.0 19.8 20.9 21.6 22.8 24.3 25.7 27.0 28.5 29.7 31.4 32.4 34.2 35.1 37.1 38.7 40.9 42.3 44.7 45.9 48.5 50.4 53.2 7.48 7.14 8.25 7.88 9.02 8.61 10.0 9.55 11.0 10.5 12.1 11.6 13.2 12.6 14.3 13.7 16.3 15.8 17.6 16.8 19.8 18.9 22.0 21.0 24.2 23.1 26.4 25.2 29.7 28.4 33.0 31.5 36.3 34.7 39.6 37.8 42.9 41.0 47.3 45.2 51.7 49.4 56.1 53.6 61.6 58.8 10 10 10 10 10 10 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 5.50 5.80 6.05 6.40 6.63 7.02 7.37 7.78 8.10 8.55 8.92 9.40 9.72 10.2 10.5 11.1 12.1 12.8 12.9 13.6 14.5 15.3 16.2 17.1 17.8 18.8 19.4 20.5 21.8 23.1 24.3 25.6 26.8 28.2 29.1 30.8 31.6 33.3 34.8 36.8 38.1 40.2 41.3 43.6 45.4 47.8 Maximum Reverse Leakage at VWM ID(uA) Maximum Peak Pulse Current IPPM (Amps) Maximum Clamping Voltage at IPPM VC (Volts) 1000 1000 500 500 200 200 50 50 10 10 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 37 38.1 34.2 35.4 32 33.1 29 29.9 26.7 27.6 24.7 25.6 23.1 24 21.1 22 18.2 18.9 17 17.8 15.1 15.9 13.7 14.4 12.5 13.1 11.5 12 10.2 10.7 9.2 9.7 8.4 8.8 7.7 8 7.1 7.4 6.5 6.7 5.9 6.2 5.4 5.7 5.0 5.2 10.8 10.5 11.7 11.3 12.5 12.1 13.8 13.4 15.0 14.5 16.2 15.6 17.3 16.7 19.0 18.2 22.0 21.2 23.5 22.5 26.5 25.2 29.1 27.7 31.9 30.6 34.7 33.2 39.1 37.5 43.5 41.4 47.7 45.7 52.0 49.9 56.4 53.9 61.9 59.3 67.8 64.8 73.5 70.1 80.5 77.0 RECTRON TRANSIENT VOLTAGE SUPPRESSORS 400W SERIES TVS DIODES / DO-214AC ( CASE 2 ) 400W Breakdown Voltage VBR @IT (Volts) TYPE P4FMAJ62 P4FMAJ62A P4FMAJ68 P4FMAJ68A P4FMAJ75 P4FMAJ75A P4FMAJ82 P4FMAJ82A P4FMAJ91 P4FMAJ91A *P4FMAJ100 * P4FMAJ100A *P4FMAJ110 *P4FMAJ110A *P4FMAJ120 *P4FMAJ120A *P4FMAJ130 *P4FMAJ130A *P4FMAJ150 *P4FMAJ150A *P4FMAJ160 *P4FMAJ160A *P4FMAJ170 *P4FMAJ170A *P4FMAJ180 * P4FMAJ180A *P4FMAJ200 *P4FMAJ200A *P4FMAJ220 *P4FMAJ220A * P4FMAJ250 *P4FMAJ250A *P4FMAJ300 *P4FMAJ300A *P4FMAJ350 *P4FMAJ350A *P4FMAJ400 *P4FMAJ400A Notes : MIN. MAX. (mA) Reverse Stand off Voltage VWM (Volts) 55.8 58.9 61.2 64.6 67.5 71.3 73.8 77.9 81.9 86.5 90.0 95.0 99.0 105 108 114 117 124 135 143 144 152 153 162 162 171 180 190 198 209 225 237 270 285 315 332 360 380 68.2 65.1 74.8 71.4 82.5 78.8 90.2 86.1 100 95.5 110 105 121 116 132 126 143 137 165 158 176 168 187 179 198 189 220 210 242 231 275 263 330 315 385 368 440 420 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 50.2 53.0 55.1 58.1 60.7 64.1 66.4 70.1 73.7 77.8 81.0 85.5 89.2 94.0 97.2 102 105 111 121 128 130 136 138 145 146 154 162 171 175 185 202 214 243 256 284 300 324 342 Maximum Reverse Leakage at VWM ID(uA) Maximum Peak Pulse Current IPPM (Amps) Maximum Clamping Voltage at IPPM VC (Volts) 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 4.7 5.0 4.2 4.5 3.8 4.0 3.5 3.7 3.2 3.3 2.1 2.2 1.9 2.0 1.7 1.8 1.6 1.7 1.4 1.4 1.3 1.4 1.2 1.3 1.2 1.2 1.0 1.1 0.9 0.9 0.83 0.87 0.70 0.73 0.60 0.62 0.53 0.55 89.0 85.0 98.0 92.0 108 103 118 113 131 125 144 137 158 152 173 165 187 179 215 207 230 219 244 234 258 246 287 274 344 328 360 344 430 414 504 482 574 548 1. VBR measured after IT applied for 300ms. IT = square pulse or equivalent. 2. For bidirectional use C or CA suffixs for all types (ex. P4FMAJ6.8C,P4FMAJ400CA) electrical characteristics apply in both directions. 3. For bidirectional types having VWM of 10 volts and less, the ID Iimit is doubled. 4. Mark" *" reverse power rating are 300w. RECTRON Mounting Pad Layout 0.094 MAX. (2.38 MAX.) 0.060 MIN. (1.52 MIN.) 0.052 MIN. (1.32 MIN.) 0.220 (5.58) REF Dimensions in inches and (millimeters) RECTRON