Preliminary SF2198E • Surface Mount 3.0 x 3.0 mm Package • Complies with Directive 2002/95/EC (RoHS) Pb 806 MHz SAW Filter Absolute Maximum Ratings Rating Value Units 10 dBm Input Power Level 3 V Operating Temperature Range DC Voltage on any Non-ground Terminal -25 to +75 °C Storage Temperature Range in Tape and Reel -30 to +85 °C 265 °C Maximum Soldering Profile, 5 cycles/10 seconds maximum SM3030-6 Electrical Characteristics Characteristic Sym Center Frequency fC Insertion Loss, 791 to 821 MHz IL Notes Min Typ Max 806 Units MHz 4.5 Amplitude Ripple, 791 to 821 MHz 3.0 VSWR, 791 to 821 MHz dB 2.5:1 Attenuation, 0 dB Reference: DC to 760 MHz 45 760 to 775 MHz 30 832 to 862 MHz 8 862 to 900 MHz 30 900 to 1500 MHz 45 1500 to 2000 MHz dB 35 Source Impedance ZS 50 Load Impedance ZL 50 Case Style SM3030-6 3.0 x 3.0 mm Nominal Footprint Lid Symbolization (Y=year, WW=week, S=shift) dot=pin 1 indicator Standard Reel Quantity Ω 928, YWWS Reel Size 7 Inch 500 Pieces/Reel Reel Size 13 Inch 3000 Pieces/Reel Electrical Connections Connection Terminals Input 2 Output 5 Case Ground 1 6 5 0 o h m L o a d All others 5 4 (b o tto m 5 0 o h m S o u rc e 2 3 v ie w ) CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. Notes: 1. 2. 3. 4. 5. 6. 7. 8. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 Ω and measured with 50 Ω network analyzer. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes." The design, manufacturing process, and specifications of this filter are subject to change. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. US and international patents may apply. RFM, stylized RFM logo, and RF Monolithics, Inc., are registered trademarks of RF Monolithics, Inc. www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. Page 1 of 5 SF2198E - 7/19/10 Filter Response Plots 806 MHz filter 0 -1 -2 -3 Att.(dB) -4 S21 -5 spec. -6 -7 -8 -9 -10 776 782 788 794 800 806 812 Freq.(MHz) 818 824 830 836 806 MHz filter 0 -10 Att.(dB) -20 -30 S21 spec. -40 -50 -60 -70 656 www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. 686 716 746 776 806 836 Freq.(MHz) 866 896 926 956 Page 2 of 5 SF2198E - 7/19/10 806 MHz filter 0 -10 -20 S21 Att.(dB) spec. -30 -40 -50 -60 -70 0 200 400 600 800 1000 1200 1400 1600 1800 2000 Freq.(MHz) 806 MHz filter 11 10 9 8 S11 VSWR 7 S22 6 spec. 5 4 3 2 1 776 www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. 782 788 794 800 806 812 Freq.(MHz) 818 824 830 836 Page 3 of 5 SF2198E - 7/19/10 SM3030-6 Case 6-Terminal Ceramic Surface-Mount Case 3.0 X 3.0 mm Nominal Footprint Case and PCB Footprint Dimensions Dimension A B C D E F G H I J K L M N O K L N K N Min 2.87 2.87 1.12 0.77 2.67 1.47 0.72 1.37 0.47 1.17 mm Nom 3.00 3.00 1.25 0.90 2.80 1.60 0.85 1.50 0.60 1.30 3.20 1.70 1.05 0.81 0.38 Max 3.13 3.13 1.38 1.03 2.93 1.73 0.98 1.63 0.73 1.43 Min 0.113 0.113 0.044 0.030 0.105 0.058 0.028 0.054 0.019 0.046 Inches Nom 0.118 0.118 0.049 0.035 0.110 0.063 0.033 0.059 0.024 0.051 0.126 0.067 0.041 0.032 0.015 Max 0.123 0.123 0.054 0.040 0.115 0.068 0.038 0.064 0.029 0.056 Case Materials O Materials N M M PCB Footprint Top View Solder Pad Plating 0.3 to 1.0 µm Gold over 1.27 to 8.89 µm Nickel Lid Plating 2.0 to 3.0 µm Nickel Body Al2O3 Ceramic Pb Free TOP VIEW BOTTOM VIEW B 1 3 6 928 YWWS A 2 5 E 4 D www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. G C F H 6 1 5 2 4 3 I J Page 4 of 5 SF2198E - 7/19/10 Tape and Reel Specifications Quantity Per Reel 7 178 500 13 330 3000 "B" REF. 100 REF. Inches “B” millimeters See Detail "A" 13. 0 12.0 20 .2 2.0 COMPONENT ORIENTATION and DIMENSIONS Carrier Tape Dimensions Ao Bo Ko Pitch W 2.0 4.0 PIN #1 A 1.50 1.75 0.3 ± 0.05 3.35 mm 3.35 mm 1.40 mm 8.0 mm 12.0 mm Bo B Ao 12.0 5.5 RO.3 (MAX.) B Pitch A Ko R0.5 (MAX.) 1.5 SECTION A-A SECTION B-B www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. USER DIRECTION OF FEED Page 5 of 5 SF2198E - 7/19/10