Preliminary SF2202E • Surface Mount 3.0 x 3.0 x 1.3 mm Package • Complies with Directive 2002/95/EC (RoHS) Pb 2017.5 MHz SAW Filter Absolute Maximum Ratings Rating Value Units 10 dBm Input Power Level DC Voltage on any Non-ground Terminal 3 V Operating Temperature Range -30 to +60 °C Storage Temperature Range in Tape and Reel -40 to +85 °C 260 °C Solder Reflow Temperature, 10 seconds, 5 cycles maximum SM3030-6 Electrical Characteristics Characteristic Sym Center Frequency FC Insertion Loss, 2010 to 2025 MHz IL Notes Min Typ Max 2017.5 Amplitude Ripple, 2010 to 2025 MHz VSWR, 2010 to 2025 MHz Units MHz 3.2 dB 1.7 dBP-P 2.1:1 Group Delay Ripple, 2010 to 2025 MHz 30 nsP-P Attenuation, Referenced to 0 dB 1 to 869 MHz 15 869 to 894 MHz 35 921 to 960 MHz 35 1805 to 1920 MHz 35 1920 to 1980 MHz 14 1980 to 1990 MHz 4.5 2045 to 2090 MHz 7 2090 to 2170 MHz 26 2300 to 2400 MHz dB 40 Source Impedance ZS 50 Load Impedance ZL 50 Case Style SM3030-6 3.0 x 3.0 mm Nominal Footprint Lid Symbolization (Y=year, WW=week, S=shift) dot=pin 1 indicator Standard Reel Quantity Ω 932, YWWS Reel Size 7 Inch 500 Pieces/Reel Reel Size 13 Inch 3000 Pieces/Reel CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. Notes: 1. 2. 3. 4. 5. 6. 7. 8. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 Ω and measured with 50 Ω network analyzer. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes." The design, manufacturing process, and specifications of this filter are subject to change. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. US and international patents may apply. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. Page 1 of 5 SF2202E - 7/16/10 Filter Response Plots www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. Page 2 of 5 SF2202E - 7/16/10 www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. Page 3 of 5 SF2202E - 7/16/10 SM3030-6 Case 6-Terminal Ceramic Surface-Mount Case 3.0 X 3.0 mm Nominal Footprint Case and PCB Footprint Dimensions Dimension A B C D E F G H I J K L M N O K L N K N mm Nom 3.00 3.00 1.25 0.90 2.80 1.60 0.85 1.50 0.60 1.30 3.20 1.70 1.05 0.81 0.38 Min 2.87 2.87 1.12 0.77 2.67 1.47 0.72 1.37 0.47 1.17 Max 3.13 3.13 1.38 1.03 2.93 1.73 0.98 1.63 0.73 1.43 Inches Nom 0.118 0.118 0.049 0.035 0.110 0.063 0.033 0.059 0.024 0.051 0.126 0.067 0.041 0.032 0.015 Min 0.113 0.113 0.044 0.030 0.105 0.058 0.028 0.054 0.019 0.046 Max 0.123 0.123 0.054 0.040 0.115 0.068 0.038 0.064 0.029 0.056 Case Materials O Materials N M M PCB Footprint Top View Solder Pad Plating 0.3 to 1.0 µm Gold over 1.27 to 8.89 µm Nickel Lid Plating 2.0 to 3.0 µm Nickel Body Al2O3 Ceramic Pb Free Electrical Connections Connection Input 5 5 0 o h m Terminals 5 2 Ground All Others TOP VIEW BOTTOM VIEW B 1 3 G C 6 932 YWWS A 2 5 0 o h m 1 , 3 , 4 , 6 Output 5 E 4 D www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. 2 F H 6 1 5 2 4 3 I J Page 4 of 5 SF2202E - 7/16/10 Tape and Reel Specifications Quantity Per Reel millimeters 7 178 500 13 330 3000 "B" REF. 100 REF. “B” Inches See Detail "A" 13. 0 12.0 20 .2 2.0 COMPONENT ORIENTATION and DIMENSIONS Carrier Tape Dimensions 2.0 3.35 mm Bo 3.35 mm Ko 1.40 mm Pitch 8.0 mm W 12.0 mm 4.0 PIN #1 A 1.50 1.75 0.3 ± 0.05 Ao Bo B Ao 12.0 5.5 RO.3 (MAX.) B Pitch A Ko R0.5 (MAX.) 1.5 SECTION A-A SECTION B-B www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. USER DIRECTION OF FEED Page 5 of 5 SF2202E - 7/16/10