Preliminary SF2215E • Low-loss 1960 MHz Filter • Complies with Directive 2002/95/EC (RoHS) Pb 1960 MHz SAW Filter Absolute Maximum Ratings Rating Value Units +10 dBm 3 V Operating Temperature Range -20 to +75 °C Storage Temperature Range in Tape and Reel -40 to +85 °C 265 °C Input Power Level DC Voltage on any Non-ground Terminal Maximum Soldering Profile, 5 cycles/10 seconds maximum SM3030-6 Electrical Characteristics Characteristic Sym Notes Min Typ Max Units Center Frequency fC 1960.0 Insertion Loss, 1927.5 to 1992.5 MHz IL 2.7 4.0 dB 1.3 2.5 dB Peak-to-Peak Amplitude Ripple, 1927.5 to 1992.5 MHz Input/Output Return Loss, 1927.5 to 1992.5 MHz 7.4 2.5 DC to 1740 MHz 20 31 1740 to 1801 MHz 30 36 1801 to 1880 MHz 20 41 2040 to 2120 MHz 25 40 2120 to 2500 MHz 31 38 3700 to 4000 MHz 25 MHz Attenuation, Referenced to 0 dB: Source Impedance ZS Load Impedance ZL Case Style 32 50 Ω 50 Ω SM3030-6 3.0 x 3.0 mm Nominal Footprint Lid Symbolization (Y=year, WW=week, S=shift) dot=pin 1 indicator Standard Reel Quantity dB 951, YWWS Reel Size 7 inch 500 Pieces/Reel Reel Size 13 inch 3000 Pieces/Reel Electrical Connections Connection Terminals Input 2 Output 5 Case Ground All others CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. Notes: 1. 2. 3. 4. 5. 6. 7. 8. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 Ω and measured with 50 Ω network analyzer. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes." The design, manufacturing process, and specifications of this filter are subject to change. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. US and international patents may apply. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc. www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. Page 1 of 5 SF2215E - 7/19/10 Filter Passband Response Filter Broadband Response www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. Page 2 of 5 SF2215E - 7/19/10 Filter Input VSWR and S11 Plots Filter Output VSWR and S22 Plots www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. Page 3 of 5 SF2215E - 7/19/10 SM3030-6 Case 6-Terminal Ceramic Surface-Mount Case 3.0 X 3.0 mm Nominal Footprint Case and PCB Footprint Dimensions Dimension A B C D E F G H I J K L M N O K L N K N mm Nom 3.00 3.00 1.25 0.90 2.80 1.60 0.85 1.50 0.60 1.30 3.20 1.70 1.05 0.81 0.38 Min 2.87 2.87 1.12 0.77 2.67 1.47 0.72 1.37 0.47 1.17 Max 3.13 3.13 1.38 1.03 2.93 1.73 0.98 1.63 0.73 1.43 Inches Nom 0.118 0.118 0.049 0.035 0.110 0.063 0.033 0.059 0.024 0.051 0.126 0.067 0.041 0.032 0.015 Min 0.113 0.113 0.044 0.030 0.105 0.058 0.028 0.054 0.019 0.046 Max 0.123 0.123 0.054 0.040 0.115 0.068 0.038 0.064 0.029 0.056 Case Materials O Materials N M M PCB Footprint Top View Solder Pad Plating 0.3 to 1.0 µm Gold over 1.27 to 8.89 µm Nickel Lid Plating 2.0 to 3.0 µm Nickel Body Al2O3 Ceramic Pb Free TOP VIEW BOTTOM VIEW B 1 3 6 951 YWWS A 2 5 E 4 D www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. G C F H 6 1 5 2 4 3 I J Page 4 of 5 SF2215E - 7/19/10 Tape and Reel Specifications “B” millimeters Quantity Per Reel 7 178 500 13 330 3000 "B" REF. 100 REF. Inches See Detail "A" 13. 0 12.0 20 .2 2.0 COMPONENT ORIENTATION and DIMENSIONS Carrier Tape Dimensions Ao Bo Ko Pitch W 2.0 4.0 PIN #1 A 1.50 1.75 0.3 ± 0.05 3.35 mm 3.35 mm 1.40 mm 8.0 mm 12.0 mm Bo B Ao 12.0 5.5 RO.3 (MAX.) B Pitch A Ko R0.5 (MAX.) 1.5 SECTION A-A SECTION B-B www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. USER DIRECTION OF FEED Page 5 of 5 SF2215E - 7/19/10