SF2225E • Low-loss 2140 MHz SAW Filter • Designed for 50 ohm Source/Load • Complies with Directive 2002/95/EC (RoHS) 2140 MHz SAW Filter Pb Absolute Maximum Ratings Rating Value Units +13 dBm Input Power Level DC Voltage on any Non-ground Terminal 3 V Operating Temperature Range -30 to +85 °C Storage Temperature Range in Tape and Reel -40 to +90 °C 265 °C Maximum Soldering Profile, 5 cycles/10 seconds maximum SM3030-6 Electrical Characteristics Characteristic Sym Notes Min Typ Max Units Center Frequency fC 2140 Insertion Loss, 2110 to 2170 MHz IL 2.1 3.5 dB Amplitude Ripple, 2110 to 2170 MHz 0.6 2.0 dBP-P Input/Output VSWR, 2110 to 2170 MHz 1.9 2.2 MHz Attenuation, Referenced to 0 dB: 10 to 500 MHz 30 32 500 to 1920 MHz 25 33 1920 to 1980 MHz 33 40 1980 to 2025 MHz 40 45 2025 to 2050 MHz 26 33 2230 to 2260 MHz 40 55 2490 to 2558 MHz 30 35 dB Source Impedance ZS 50 Load Impedance ZL 50 Case Style SM3030-6 3.0 x 3.0 mm Nominal Footprint Lid Symbolization (Y=year, WW=week, S=shift) dot=pin 1 indicator Standard Reel Quantity 961, YWWS Reel Size 7 inch 500 Pieces/Reel Reel Size 13 inch 3000 Pieces/Reel Electrical Connections Connection Input Terminals 2 Output 5 Case Ground All others CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. Notes: 1. 2. 3. 4. 5. 6. 7. 8. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 and measured with 50 network analyzer. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes." The design, manufacturing process, and specifications of this filter are subject to change. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. US and international patents may apply. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc. www.RFM.com E-mail: [email protected] © 2010-2012 by RF Monolithics, Inc. Page 1 of 5 SF2225E - 3/14/12 Filter Passband Response, 1800 to 2500 MHz Filter Wideband Response, 10 to 5000 MHz www.RFM.com E-mail: [email protected] © 2010-2012 by RF Monolithics, Inc. Page 2 of 5 SF2225E - 3/14/12 Filter Input Impedance Filter Output Impedance www.RFM.com E-mail: [email protected] © 2010-2012 by RF Monolithics, Inc. Page 3 of 5 SF2225E - 3/14/12 SM3030-6 Case 6-Terminal Ceramic Surface-Mount Case 3.0 X 3.0 mm Nominal Footprint Case and PCB Footprint Dimensions Dimension A B C D E F G H I J K L M N O K L N K N mm Nom 3.00 3.00 1.25 0.90 2.80 1.60 0.85 1.50 0.60 1.30 3.20 1.70 1.05 0.81 0.38 Min 2.87 2.87 1.12 0.77 2.67 1.47 0.72 1.37 0.47 1.17 Max 3.13 3.13 1.38 1.03 2.93 1.73 0.98 1.63 0.73 1.43 Inches Nom 0.118 0.118 0.049 0.035 0.110 0.063 0.033 0.059 0.024 0.051 0.126 0.067 0.041 0.032 0.015 Min 0.113 0.113 0.044 0.030 0.105 0.058 0.028 0.054 0.019 0.046 Max 0.123 0.123 0.054 0.040 0.115 0.068 0.038 0.064 0.029 0.056 Case Materials O Materials N M M PCB Footprint Top View Solder Pad Plating 0.3 to 1.0 µm Gold over 1.27 to 8.89 µm Nickel Lid Plating 2.0 to 3.0 µm Nickel Body Al2O3 Ceramic Pb Free TOP VIEW BOTTOM VIEW B 6 1 3 961 YWWS A 2 5 E 4 D www.RFM.com E-mail: [email protected] © 2010-2012 by RF Monolithics, Inc. G C F H 6 1 5 2 4 3 I J Page 4 of 5 SF2225E - 3/14/12 “B” millimeters Inches "B" REF. 100 REF. Tape and Reel Specifications Quantity Per Reel 7 178 500 13 330 3000 See Detail "A" 13. 0 12.0 20 .2 2.0 COMPONENT ORIENTATION and DIMENSIONS Carrier Tape Dimensions Ao Bo Ko Pitch W 2.0 4.0 PIN #1 A 1.50 1.75 0.3 ± 0.05 3.35 mm 3.35 mm 1.40 mm 8.0 mm 12.0 mm Bo B Ao 12.0 5.5 RO.3 (MAX.) B Pitch A Ko R0.5 (MAX.) 1.5 SECTION A-A SECTION B-B www.RFM.com E-mail: [email protected] © 2010-2012 by RF Monolithics, Inc. USER DIRECTION OF FEED Page 5 of 5 SF2225E - 3/14/12