RICHTEK RT8282B

RT8282B
2A, 23V, 1.2MHz Synchronous Step-Down Converter
General Description
The RT8282B is a high efficiency, monolithic synchronous
step-down DC/DC converter that can deliver up to 2A
output current from a 4.5V to 23V input supply. The
RT8282B's current mode architecture and external
compensation allow the transient response to be
optimized over a wide range of loads and output capacitors.
Cycle-by-cycle current limit provides protection against
shorted outputs and soft-start eliminates input current
surge during start-up. The RT8282B also provides under
voltage protection and thermal shutdown protection. The
low current (<3μA) shutdown mode provides output
disconnect, enabling easy power management in batterypowered systems. The RT8282B is available in a
SOP-8 (Exposed Pad) package.
Ordering Information
RT8282B
Package Type
SP : SOP-8 (Exposed Pad-Option 1)
Lead Plating System
G : Green (Halogen Free and Pb Free)
H : UVP Hiccup
L : UVP Latch-Off
Note :
Richtek products are :
`
Features
±1.5% High Accuracy Feedback Voltage
4.5V to 23V Input Voltage Range
2A Output Current
Integrated N-MOSFET Switches
Current Mode Control
Fixed Frequency Operation : 1.2MHz
Adjustable Output from 0.8V to 20V
Up to 95% Efficiency
Programmable Soft-Start
Stable with Low-ESR Ceramic Output Capacitors
Cycle-by-Cycle Over Current Protection
Input Under Voltage Lockout
Output Under Voltage Protection
Thermal Shutdown Protection
RoHS Compliant and Halogen Free
Applications
Wireless AP/Router
Set-Top-Box
Industrial and Commercial Low Power Systems
LCD Monitors and TVs
Green Electronics/Appliances
Point of Load Regulation of High-Performance DSPs
Pin Configurations
(TOP VIEW)
RoHS compliant and compatible with the current requirements of IPC/JEDEC J-STD-020.
`
Suitable for use in SnPb or Pb-free soldering processes.
Marking Information
8
BOOT
VIN
2
SW
GND
3
GND
7
EN
6
COMP
5
FB
9
4
SS
RT8282BGSP : Product Number
RT8282B
xGSPYMDNN
x : H or L
SOP-8 (Expoaed Pad)
YMDNN : Date Code
DS8282B-01 March 2011
www.richtek.com
1
RT8282B
Typical Application Circuit
2
VIN
4.5V to 23V
CIN
10µF
REN 100k
CSS
0.1µF
BOOT
VIN
1
RT8282B
SW 3
7 EN
8 SS
4, 9 (Exposed Pad)
GND
CBOOT
L
100nF 3.6µH
R1
75k
FB 5
COMP
6
CC
RC
0.82nF 32k
VOUT
3.3V/2A
COUT
22µF x 2
R2
24k
CP
Open
Recommended Component Selection
VOUT (V) R1 (kΩ) R2 (kΩ) RC (kΩ)
8
27
3
75
5
62
11.8
47
3.3
75
24
32
2.5
25.5
12
25.5
1.5
10.5
12
15
1.2
12
24
12
1
3
12
10
CC (nF)
0.82
0.82
0.82
0.82
0.82
0.82
0.82
L (μH)
10
6.8
3.6
3.6
2
2
2
COUT (μF)
22 x 2
22 x 2
22 x 2
22 x 2
22 x 2
22 x 2
22 x 2
Functional Pin Description
Pin No.
Pin Name
1
BOOT
2
VIN
3
SW
4,
9 (Exposed Pad)
GND
5
FB
6
COMP
7
EN
8
SS
www.richtek.com
2
Pin Function
Bootstrap for High Side Gate Driver. Connect a 0.1μF or greater ceramic
capacitor from BOOT to SW pins.
Input Supply Voltage 4.5V to 23V. Must bypass with a suitably large ceramic
capacitor.
Switch Node--Connect this pin to an external L-C filter.
Ground. The exposed pad must be soldered to a large PCB and connected to
GND for maximum power dissipation.
Feedback Input. This pin is connected to the converter output. It is used to set
the output of the converter to regulate to the desired value via an internal
resistive divider. For an adjustable output, an external resistive divider is
connected to this pin.
Compensation Node. COMP is used to compensate the regulation control
loop. Connect a series RC network from COMP to GND. In some cases, an
additional capacitor from COMP to GND is required.
Chip Enable (Active High). A logic low forces the RT8282B into shutdown
mode reducing the supply current to less than 3μA. Attach this pin to VIN with
a 100kΩ pull up resistor for automatic startup.
Soft-Start Control Input. SS controls the soft-start period. Connect a capacitor
from SS to GND to set the soft-start period. A 0.1μF capacitor sets the
soft-start period to 13.5ms.
DS8282B-01 March 2011
RT8282B
Function Block Diagram
VIN
Internal
Regulator
Oscillator
Slope Comp
Shutdown
Comparator VA VCC
1.2V
5k
EN
Foldback
Control
+
-
Current Sense
Amplifier
+
-
VA
0.4V
+
UV
Comparator
Lockout
Comparator
+
2.7V
3V
VCC
BOOT
S
+
R
Current
Comparator
Q
130mΩ
Q
130mΩ
SW
GND
6µA
0.8V
SS
FB
DS8282B-01 March 2011
+
+EA
-
COMP
www.richtek.com
3
RT8282B
Absolute Maximum Ratings
(Note 1)
Supply Voltage, VIN ------------------------------------------------------------------------------------------------- −0.3V to 25V
Input Voltage, SW --------------------------------------------------------------------------------------------------- −0.3V to (VIN + 0.3V)
VBOOT - VSW ----------------------------------------------------------------------------------------------------------- −0.3V to 6V
Other Pin Voltages ------------------------------------------------------------------------------------------------- −0.3V to 6V
Power Dissipation, PD @ TA = 25°C
SOP-8 (Exposed Pad) --------------------------------------------------------------------------------------------Package Thermal Resistance (Note 2)
SOP-8 (Exposed Pad), θJA ---------------------------------------------------------------------------------------SOP-8 (Εxposed Pad), θJC --------------------------------------------------------------------------------------Lead Temperature (Soldering, 10 sec.) ------------------------------------------------------------------------Junction Temperature ----------------------------------------------------------------------------------------------Storage Temperature Range -------------------------------------------------------------------------------------ESD Susceptibility (Note 3)
HBM (Human Body Mode) ---------------------------------------------------------------------------------------MM (Machine Mode) ------------------------------------------------------------------------------------------------
Recommended Operating Conditions
1.333W
75°C/W
15°C/W
260°C
150°C
−40°C to 150°C
2kV
200V
(Note 4)
Supply Voltage, VIN ------------------------------------------------------------------------------------------------- 4.5V to 23V
Junction Temperature Range -------------------------------------------------------------------------------------- −40°C to 125°C
Ambient Temperature Range -------------------------------------------------------------------------------------- −40°C to 85°C
Electrical Characteristics
(VIN = 12V, TA = 25°C, unless otherwise specified)
Parameter
Symbol
Test Conditions
Min
Typ
Max
Unit
Shutdown Supply Current
VEN = 0V
--
0.5
3
μA
Supply Current
VEN = 3 V, VFB = 0.9V
--
0.8
1.2
mA
0.788
0.8
0.812
V
--
940
--
μA/V
RDS(ON)1
--
130
--
mΩ
RDS(ON)2
--
130
--
mΩ
--
0
10
μA
3.5
4.5
--
A
--
1.2
--
A
GCS
--
5
--
A/V
FOSC1
1
1.2
1.4
μHz
Feedback Voltage
Error Amplifier
Transconductance
High Side Switch
On-Resistance
Low Side Switch
On-Resistance
High Side Switch Leakage
Current
Upper Switch Current Limit
Lower Switch Current Limit
COMP to Current Sense
Transconductance
Oscillation Frequency
VFB
4.5V ≤ VIN ≤ 23V
GEA
ΔIC = ± 10μA
VEN = 0V, VSW = 0V
Min. Duty Cycle, VBOOT − VSW = 4.8V
From Drain to Source
Short Circuit Oscillation
Frequency
Maximum Duty Cycle
FOSC2
VFB = 0V
--
300
--
kHz
DMAX
VFB = 0.7V
--
75
--
%
Minimum On Time
tON
--
100
--
ns
To be continued
www.richtek.com
4
DS8282B-01 March 2011
RT8282B
Parameter
EN Threshold Voltage
Symbol
Test Conditions
Min
Typ
Max
Unit
Logic High
VIH
2.7
--
5.5
Logic Low
VIL
--
--
0.4
3.8
4.2
4.5
V
--
320
--
mV
Input Under Voltage Lockout Threshold
V IN Rising
Input Under Voltage Lockout Hysteresis
V
Soft-Start Current
V SS = 0V
--
6
--
μA
Soft-Start Period
CSS = 0.1μF
--
13.5
--
ms
--
150
--
°C
Thermal Shutdown
TSD
Note 1. Stresses listed as the above "Absolute Maximum Ratings" may cause permanent damage to the device. These are for
stress ratings. Functional operation of the device at these or any other conditions beyond those indicated in the
operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended
periods may remain possibility to affect device reliability.
Note 2. θJA is measured in natural convection at TA = 25°C on a high effective thermal conductivity four-layer test board of
JEDEC 51-7 thermal measurement standard. The measurement case position of θJC is on the expose pad for
SOP-8 (Exposed Pad) package.
Note 3. Devices are ESD sensitive. Handling precaution is recommended.
Note 4. The device is not guaranteed to function outside its operating conditions.
DS8282B-01 March 2011
www.richtek.com
5
RT8282B
Typical Operating Characteristics
Efficiency vs. Output Current
Reference Voltage vs. Input Voltage
100
0.820
90
0.815
70
Reference Voltage (V)
Efficiency (%)
80
VIN = 12V
VIN = 23V
60
50
40
30
20
0.810
0.805
0.800
0.795
0.790
0.785
10
VOUT = 3.3V
VOUT = 3.3V, IOUT = 0A
0
0.780
0.0
0.3
0.5
0.8
1.0
1.3
1.5
1.8
2.0
4
6
8
10
Output Current (A)
16
18
20
22
24
Output Voltage vs. Output Current
Reference Voltage vs. Temperature
3.36
3.35
Output Voltage (V)1
0.815
Reference Voltage (V)
14
Input Voltage (V)
0.820
0.810
0.805
0.800
0.795
0.790
3.34
3.33
3.32
3.31
3.30
VIN = 23V
VIN = 12V
3.29
3.28
3.27
3.26
0.785
3.25
VIN = 12V, VOUT = 3.3V, IOUT = 0A
0.780
VOUT = 3.3V
3.24
-40 -25 -10
5
20
35
50
65
80
95 110 125
0.0
0.2
0.4
0.6
Temperature (°C)
0.8
1.0
1.2
1.4
1.6
1.8
2.0
Output Current (A)
Frequency vs. Temperature
Frequency. vs. Input Voltage
1.40
1.40
1.35
1.35
1.30
1.30
Frequency (MHz)1
Frequency (MHz)1
12
1.25
1.20
1.15
1.10
1.05
1.25
1.20
1.15
1.10
1.05
VOUT = 3.3V, IOUT = 0A
VIN = 12V, VOUT = 3.3V, IOUT = 0A
1.00
1.00
4
6
8
10
12
14
16
18
Input Voltage (V)
www.richtek.com
6
20
22
24
-40 -25 -10
5
20
35
50
65
80
95 110 125
Temperature (°C)
DS8282B-01 March 2011
RT8282B
Current Limit VS. Temperature
6.0
5.5
5.5
Current Limit (A)
Current Limit (A)
Current Limit vs. Duty Cycle
6.0
5.0
4.5
4.0
5.0
4.5
4.0
3.5
3.5
VIN = 4.5V to 23V, VOUT = 3.3V
3.0
VIN = 12V, VOUT = 3.3V
3.0
0
10
20
30
40
50
60
70
80
-50
Duty Cycle (%)
-25
0
25
50
75
100
125
Temprature (°C)
Output Current Limit vs. Input Voltage
Load Transient Response
6.0
Output Current Limit (A)
5.5
5.0
VOUT
(50mV/Div)
4.5
4.0
3.5
VOUT = 1.2V
VOUT = 3.3V (Add Bootstrap Diode)
VOUT = 3.3V
3.0
2.5
2.0
IOUT
(2A/Div)
1.5
1.0
0.5
VIN = 12V, VOUT = 3.3V, IOUT = 0A to 2A
0.0
4
6
8
10
12
14
16
18
20
22
24
Time (100μs/Div)
Input Voltage (V)
Load Transient Response
VOUT
(50mV/Div)
Switching
VOUT
(10mV/Div)
VSW
(10V/Div)
IOUT
(2A/Div)
IL
(1A/Div)
VIN = 12V, VOUT = 3.3V, IOUT = 1A to 2A
Time (100μs/Div)
DS8282B-01 March 2011
VIN = 12V, VOUT = 3.3V, IOUT = 2A
Time (500ns/Div)
www.richtek.com
7
RT8282B
Switching
Power On from VIN
VOUT
(10mV/Div)
VIN
(5V/Div)
VSW
(10V/Div)
IL
(1A/Div)
VOUT
(2V/Div)
VIN = 12V, VOUT = 3.3V, IOUT = 1A
IL
(2A/Div)
VIN = 12V, VOUT = 3.3V, IOUT = 2A
Time (500ns/Div)
Time (5ms/Div)
Power Off from VIN
Power On from EN
VEN
(5V/Div)
VIN
(5V/Div)
VOUT
(2V/Div)
VOUT
(2V/Div)
IL
(2A/Div)
IL
(2A/Div)
VIN = 12V, VOUT = 3.3V, IOUT = 2A
VIN = 12V, VOUT = 3.3V, IOUT = 2A
Time (5ms/Div)
Time (5ms/Div)
Power Off from EN
VEN
(5V/Div)
VOUT
(2V/Div)
IL
(2A/Div)
VIN = 12V, VOUT = 3.3V, IOUT = 2A
Time (5ms/Div)
www.richtek.com
8
DS8282B-01 March 2011
RT8282B
Application Information
The RT8282B is a synchronous high voltage buck converter
that can support the input voltage range from 4.5V to 23V
and the output current can be up to 2A.
Output Voltage Setting
The resistive divider allows the FB pin to sense the output
voltage as shown in Figure 1.
Soft-Start
The RT8282B contains an external soft-start clamp that
gradually raises the output voltage. The soft-start timing
can be programmed by the external capacitor between
SS pin and GND. The chip provides a 6μA charge current
for the external capacitor. If 0.1μF capacitor is used to set
the soft-start, it's period will be 13.5ms (typ.).
VOUT
Chip Enable Operation
R1
FB
RT8282B
R2
GND
Figure 1. Output Voltage Setting
The output voltage is set by an external resistive voltage
divider according to the following equation :
VOUT = VFB ⎛⎜ 1+ R1 ⎞⎟
⎝ R2 ⎠
Where VFB is the feedback reference voltage (0.8V typ.).
External Bootstrap Diode
Connect a 100nF low ESR ceramic capacitor between
the BOOT pin and SW pin. This capacitor provides the
gate driver voltage for the high side MOSFET.
The EN pin is the chip enable input. Pulling the EN pin
low (<0.4V) will shutdown the device. During shutdown
mode, the RT8282B quiescent current will drops below
3μA. Driving the EN pin high (>2.7V, < 5.5V) will turn on
the device again. For external timing control (e.g.RC),
the EN pin can also be externally pulled high by adding a
R EN* resistor and C EN* capacitor from the VIN pin
(see Figure 5).
An external MOSFET can be added to implement digital
control on the EN pin when no system voltage above 2.5V
is available, as shown in Figure 3. In this case, a 100kΩ
pull-up resistor, REN, is connected between VIN and the
EN pin. MOSFET Q1 will be under logic control to pull
down the EN pin.
2
VIN
REN
100k
Chip Enable
It is recommended to add an external bootstrap diode
between an external 5V and BOOT pin for efficiency
improvement when input voltage is lower than 5.5V or duty
ratio is higher than 65% .The bootstrap diode can be a
low cost one such as IN4148 or BAT54. The external 5V
can be a 5V fixed input from system or a 5V output of the
RT8282B. Note that the external boot voltage must be
lower than 5.5V.
5V
BOOT
RT8282B
100nF
SW
VIN
CIN
BOOT
1
CBOOT
RT8282B
7 EN
VOUT
L
SW 3
R1
Q1
8 SS
CSS
4,
9 (Exposed Pad)
GND
COUT
FB 5
COMP
6
CC
RC
R2
CP
Figure 3. Enable Control Circuit for Logic Control with
Low Voltage
To prevent enabling circuit when VIN is smaller than the
VOUT target value, a resistive voltage divider can be placed
between the input voltage and ground and connected to
the EN pin to adjust IC lockout threshold, as shown in
Figure 4. For example, if an 8V output voltage is regulated
from a 12V input voltage, the resistor REN2 can be selected
to set input lockout threshold larger than 8V.
Figure 2. External Bootstrap Diode
DS8282B-01 March 2011
www.richtek.com
9
RT8282B
2
VIN
12V
REN1
100k
CIN
10µF
VIN
BOOT
1
CBOOT
L
RT8282B
7 EN
SW 3
VOUT
8V
R1
REN2
8 SS
CSS
4,
9 (Exposed Pad)
GND
COUT
FB 5
COMP
6
CC
RC
R2
CP
Figure 4. The Resistors can be Selected to Set IC
Lockout Threshold
Hiccup Mode
For the RT8282BH, it provides Hiccup Mode Under Voltage
Protection (UVP). When the FB voltage drops below half
of the feedback reference voltage, VFB, the UVP function
will be triggered and the RT8282BH will shut down for a
period of time and then recover automatically. The Hiccup
Mode UVP can reduce input current in short-circuit
conditions.
Latch-Off Mode
For the RT8282BL, it provides Latch-Off Mode Under
Voltage Protection (UVP). When the FB voltage drops
below half of the feedback reference voltage, VFB, UVP
will be triggered and the RT8282BL will shut down in LatchOff Mode. In shutdown condition, the RT8282BL can be
reset by EN pin or power input VIN.
Inductor Selection
The inductor value and operating frequency determine the
ripple current according to a specific input and output
voltage. The ripple current ΔIL increases with higher VIN
and decreases with higher inductance :
V
V
ΔIL = ⎡⎢ OUT ⎤⎥ × ⎡⎢1− OUT ⎤⎥
VIN ⎦
⎣ f ×L ⎦ ⎣
Having a lower ripple current reduces not only the ESR
losses in the output capacitors but also the output voltage
ripple. High frequency with small ripple current can achieve
highest efficiency operation. However, it requires a large
inductor to achieve this goal.
For the ripple current selection, the value of ΔIL = 0.24(IMAX)
will be a reasonable starting point. The largest ripple
current occurs at the highest VIN. To guarantee that the
www.richtek.com
10
ripple current stays below the specified maximum, the
inductor value should be chosen according to the following
equation :
⎡ VOUT ⎤ ⎡
VOUT ⎤
L =⎢
× ⎢1 −
⎥
⎥
f
I
V
×
Δ
L(MAX) ⎦ ⎣
IN(MAX) ⎦
⎣
The inductor's current rating (caused a 40°C temperature
rising from 25°C ambient) should be greater than the
maximum load current and its saturation current should
be greater than the short circuit peak current limit. Please
see Table 2 for the inductor selection reference.
Table 2. Suggested Inductors for Typical
Application Circuit
Component
Supplier
Series
Dimensions
(mm)
TDK
VLF10045
10 x 9.7 x 4.5
TDK
TAIYO
YUDEN
SLF12565
12.5 x 12.5 x 6.5
NR8040
8x8x4
CIN and COUT Selection
The input capacitance, C IN, is needed to filter the
trapezoidal current at the source of the high side MOSFET.
To prevent large ripple current, a low ESR input capacitor
sized for the maximum RMS current should be used. The
RMS current is given by :
V
IRMS = IOUT(MAX) OUT
VIN
VIN
−1
VOUT
This formula has a maximum at VIN = 2VOUT, where
I RMS = I OUT /2. This simple worst-case condition is
commonly used for design because even significant
deviations do not offer much relief.
Choose a capacitor rated at a higher temperature than
required. Several capacitors may also be paralleled to
meet size or height requirements in the design.
For the input capacitor, one 10μF low ESR ceramic
capacitors are recommended. For the recommended
capacitor, please refer to table 3 for more detail.
The selection of COUT is determined by the required ESR
to minimize voltage ripple.
Moreover, the amount of bulk capacitance is also a key
for COUT selection to ensure that the control loop is stable.
Loop stability can be checked by viewing the load transient
DS8282B-01 March 2011
RT8282B
response as described in a later section.
and be mistaken as loop instability. At worst, a sudden
inrush of current through the long wires can potentially
cause a voltage spike at VIN large enough to damage the
part.
The output ripple, ΔVOUT , is determined by :
1
⎤
ΔVOUT ≤ ΔIL ⎡⎢ESR +
8fCOUT ⎥⎦
⎣
The output ripple will be highest at the maximum input
Checking Transient Response
voltage since ΔIL increases with input voltage. Multiple
capacitors placed in parallel may be needed to meet the
ESR and RMS current handling requirement. Dry tantalum,
special polymer, aluminum electrolytic and ceramic
capacitors are all available in surface mount
packages.Special polymer capacitors offer very low ESR
value. However, it provides lower capacitance density than
other types. Although Tantalum capacitors have the highest
capacitance density, it is important to only use types that
pass the surge test for use in switching power supplies.
Aluminum electrolytic capacitors have significantly higher
ESR. However, it can be used in cost-sensitive applications
for ripple current rating and long term reliability
considerations. Ceramic capacitors have excellent low
ESR characteristics but can have a high voltage coefficient
and audible piezoelectric effects. The high Q of ceramic
capacitors with trace inductance can also lead to significant
ringing.
The regulator loop response can be checked by looking
at the load transient response. Switching regulators take
several cycles to respond to a step in load current. When
a load step occurs, VOUT immediately shifts by an amount
equal to ΔILOAD (ESR) also begins to charge or discharge
COUT generating a feedback error signal for the regulator
to return VOUT to its steady-state value. During this
recovery time, VOUT can be monitored for overshoot or
ringing that would indicate a stability problem.
EMI Consideration
Since parasitic inductance and capacitance effects in PCB
circuitry would cause a spike voltage on SW pin when
high side MOSFET is turned-on/off, this spike voltage on
SW may impact on EMI performance in the system. In
order to enhance EMI performance, there are two methods
to suppress the spike voltage. One is to place an R-C
snubber between SW and GND and make them as close
as possible to the SW pin (see Figure 5). Another method
is adding a resistor in series with the bootstrap
capacitor, CBOOT. But this method will decrease the driving
capability to the high side MOSFET. It is strongly
recommended to reserve the R-C snubber during PCB
layout for EMI improvement. Moreover, reducing the SW
trace area and keeping the main power in a small loop will
be helpful on EMI performance. For detailed PCB layout
guide, please refer to the section of Layout Consideration.
Higher values, lower cost ceramic capacitors are now
becoming available in smaller case sizes. Their high ripple
current, high voltage rating and low ESR make them ideal
for switching regulator applications. However, care must
be taken when these capacitors are used at input and
output. When a ceramic capacitor is used at the input
and the power is supplied by a wall adapter through long
wires, a load step at the output can induce ringing at the
input, VIN. At best, this ringing can couple to the output
2
VIN
4.5V to 23V
REN*
Chip Enable
CIN
10µF
VIN
BOOT
1
CBOOT
L
100nF 3.6µH
RT8282B
7 EN
SW 3
R S*
CEN*
8 SS
CSS
4,
0.1µF 9 (Exposed Pad)
* : Optional
RBOOT*
GND
R1
75k
CS*
FB 5
COMP
6
VOUT
3.3V/2A
CC
RC
0.82nF 32k
COUT
22µFx2
R2
24k
CP
NC
Figure 5. Reference Circuit with Snubber and Enable Timing Control
DS8282B-01 March 2011
www.richtek.com
11
RT8282B
For continuous operation, do not exceed the maximum
operation junction temperature 125°C. The maximum
power dissipation depends on the thermal resistance of
IC package, PCB layout, the rate of surroundings airflow
and temperature difference between junction to ambient.
The maximum power dissipation can be calculated by
following formula :
PD(MAX) = (TJ(MAX) − TA ) / θJA
Where T J(MAX) is the maximum operation junction
temperature , TA is the ambient temperature and the θJA is
the junction to ambient thermal resistance.
For recommended operating conditions specification of
RT8282B, the maximum junction temperature is 125°C.
The junction to ambient thermal resistance θJA is layout
dependent. For PSOP-8 package, the thermal resistance
derating curves allows the designer to see the effect of
rising ambient temperature on the maximum power
dissipation allowed.
2.2
Four-Layer PCB
2.0
Power Dissipation (W)
Thermal Considerations
1.8
Copper Area
70mm2
50mm2
30mm2
10mm2
Min.Layout
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
0
25
50
75
100
125
Ambient Temperature (°C)
Figure 7. Derating Curves for RT8282B Package
θJA is 75°C/W on the standard JEDEC 51-7 four-layer
thermal test board. The maximum power dissipation at
TA = 25°C can be calculated by following formula :
P D(MAX) = (125°C − 25°C) / (75°C/W) = 1.333W
(min.copper area PCB layout)
P D(MAX) = (125°C − 25°C) / (49°C/W) = 2.04W
(70mm2copper area PCB layout)
The thermal resistance θJA of SOP-8 (Exposed Pad) is
determined by the package architecture design and the
PCB layout design. However, the package architecture
design had been designed. If possible, it's useful to
increase thermal performance by the PCB layout copper
design. The thermal resistance θJA can be decreased by
adding copper area under the exposed pad of SOP-8
(Exposed Pad) package.
As shown in Figure 6, the amount of copper area to which
the SOP-8 (Exposed Pad) is mounted affects thermal
performance. When mounted to the standard
SOP-8 (Exposed Pad) pad (Figure 6.a), θJA is 75°C/W.
Adding copper area of pad under the SOP-8 (Exposed
Pad) (Figure 6.b) reduces the θJA to 64°C/W. Even further,
increasing the copper area of pad to 70mm2 (Figure 6.e)
reduces the θJA to 49°C/W.
(a) Copper Area = (2.3 x 2.3) mm2, θJA = 75°C/W
(b) Copper Area = 10mm2, θJA = 64°C/W
(c) Copper Area = 30mm2 , θJA = 54°C/W
The maximum power dissipation depends on operating
ambient temperature for fixed T J(MAX) and thermal
resistance θJA. For RT8282B packages, the Figure 7 of
www.richtek.com
12
DS8282B-01 March 2011
RT8282B
(d) Copper Area = 50mm2 , θJA = 51°C/W
(e) Copper Area = 70mm2 , θJA = 49°C/W
Figure 6. Themal Resistance vs. Copper Area Layout Design
Layout Consideration
`
For best performance of the RT8282B, the follow layout
guidelines must be strictly followed.
SW should be connected to inductor by wide and short
trace. Keep sensitive components away from this trace.
`
The feedback components must be connected as close
to the device as possible
`
Input capacitor must be placed as close to the IC as
possible.
VIN
GND
SW GND
The feedback components
must be connected as close
to the device as possible.
CC
CIN
CSS
Input capacitor must
be placed as close
to the IC as possible.
BOOT
RS CS
VIN
2
SW
3
GND
4
GND
8
SS
7
EN
6
COMP
5
FB
9
COUT
VOUT
L1
SW should be connected to inductor by
wide and short trace. Keep sensitive
components away from this trace.
REN VIN
CP
RC
R1
R2
VOUT
GND
Figure 8. PCB Layout Guide
Table 3. Suggested Capacitors for CIN and COUT
Location
Component Supplier
Part No.
Capacitance (μF)
Case Size
CIN
MURATA
GRM31CR61E106K
10
1206
CIN
TDK
C3225X5R1E106K
10
1206
CIN
TAIYO YUDEN
TMK316BJ106ML
10
1206
COUT
MURATA
GRM31CR60J476M
47
1206
COUT
TDK
C3225X5R0J476M
47
1210
COUT
MURATA
GRM32ER71C226M
22
1210
COUT
TDK
C3225X5R1C22M
22
1210
DS8282B-01 March 2011
www.richtek.com
13
RT8282B
Outline Dimension
H
A
M
EXPOSED THERMAL PAD
(Bottom of Package)
Y
J
X
B
F
C
I
D
Dimensions In Millimeters
Symbol
Dimensions In Inches
Min
Max
Min
Max
A
4.801
5.004
0.189
0.197
B
3.810
4.000
0.150
0.157
C
1.346
1.753
0.053
0.069
D
0.330
0.510
0.013
0.020
F
1.194
1.346
0.047
0.053
H
0.170
0.254
0.007
0.010
I
0.000
0.152
0.000
0.006
J
5.791
6.200
0.228
0.244
M
0.406
1.270
0.016
0.050
X
2.000
2.300
0.079
0.091
Y
2.000
2.300
0.079
0.091
X
2.100
2.500
0.083
0.098
Y
3.000
3.500
0.118
0.138
Option 1
Option 2
8-Lead SOP (Exposed Pad) Plastic Package
Richtek Technology Corporation
Richtek Technology Corporation
Headquarter
Taipei Office (Marketing)
5F, No. 20, Taiyuen Street, Chupei City
5F, No. 95, Minchiuan Road, Hsintien City
Hsinchu, Taiwan, R.O.C.
Taipei County, Taiwan, R.O.C.
Tel: (8863)5526789 Fax: (8863)5526611
Tel: (8862)86672399 Fax: (8862)86672377
Email: [email protected]
Information that is provided by Richtek Technology Corporation is believed to be accurate and reliable. Richtek reserves the right to make any change in circuit
design, specification or other related things if necessary without notice at any time. No third party intellectual property infringement of the applications should be
guaranteed by users when integrating Richtek products into any application. No legal responsibility for any said applications is assumed by Richtek.
www.richtek.com
14
DS8282B-01 March 2011