ELECTRONICS Transient Voltage Suppressors P4SMA Series Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Transient Voltage Suppressors - P4SMA Series Features UNI 1. Halogen-free 2. Rohs compliant 3. Typical maximum temperature coefficient 4. ΔVBR=0.1%xVBR@25°C x ΔT 5. Glass passivated Chip junction in DO-214AC package BI 6. 400W peak pulse capadility at 10x1000μs waveform,repetition rate (duty cycles):0.01% 7. Fast response time:typically less than 1.0ps from 0 Volts to BV min 8. Excellent clamping capability 9. Low incremental surge resistance 10. Typical IR less than 5μA above 11V BI Cathode 11. High temperature soldering guaranteed: 260°C/40 seconds / 0.375”, Anode (9.5mm) lead length, 5lbs., (2.3kg)tension 12. Plastic package has underwriters laboratory UNI flammability classification 94v-0 Applications TVS devices are ideal for the protection of I/O interfaces,VCC bus and other vulnerable circuits used in telecom, computer, industrial and consumer electronic applications. Mechanical Characteristics Rating Symbol Value Units Peak Pulse Power Dissipation at TA=25°C by 10x1000μs test waveform (Fig.1)(Note 1),(Note 2) PPPM 400 Watts Power Dissipation on inifinite heat sink at TA=50°C PD 3.3 Watts IFSM 40 Amps VF 3.5/6.5 V Operating junction and Storage Temperature Range. TJ,TSTG -55°C to 175°C °C Typical Thermal Resistance Junction to Lead RuJL 30 °C/W Typical Thermal Resistance Junction to Ambient RuJA 120 °C/W Peak Forward Surge Current, 8.3ms Single Half Sine Wave(Note 3) Maximum Instantaneous Forward Voltage at 25A for Unidirectional only (Note 4) Notes: 1. Non-repetitive current pulse , per Fig. 3 and derated above TA = 25°C per Fig. 2. 2. Measured on 8.3ms single half sine wave or equivalent square wave, duty cycle=4 perminute maximum. 3. VF<3.5V for devices of VBR _< 200V and VF<5.0V for devices of VBR _> 201V. Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:1 Transient Voltage Suppressors - P4SMA Series Electriacl Characteristics Type Number Reverse StandOff Voltage Breakdown Voltage@IT Test Current VBR MIN.(V) VBR.MAX.(V) 6.40 7.25 IT(mA) 10 (UNI) (BI) P4SMA6.8A P4SMA6.8CA VRWM(V) 5.80 P4SMA7.5A P4SMA7.5CA 6.40 7.22 8.30 P4SMA8.2A P4SMA8.2CA 7.02 7.78 P4SMA9.1A P4SMA9.1CA 7.78 P4SMA10A P4SMA10CA P4SMA11A Maximum Clamping Voltage@IPP VC(V) Peak Pulse Current Reverse Leakage @VRWM IR(µA) 9.2 IPP(A) 43.5 10 10.3 38.8 800 8.95 10 12.0 33.3 200 8.33 9.58 1 12.9 31.0 100 8.55 9.44 10.82 1 13.6 29.4 50 P4SMA11CA 9.40 10.00 11.50 1 18.2 22.0 5 P4SMA12A P4SMA12CA 10.20 11.10 12.80 1 19.9 20.1 5 P4SMA13A P4SMA13CA 11.10 12.20 14.00 1 21.5 18.6 5 P4SMA15A P4SMA15CA 12.80 14.40 16.50 1 24.4 16.4 5 P4SMA16A P4SMA16CA 13.60 15.60 17.90 1 26.0 15.3 5 P4SMA18A P4SMA18CA 15.30 16.70 19.20 1 29.2 13.7 5 P4SMA20A P4SMA20CA 17.10 18.90 21.70 1 32.4 12.3 5 P4SMA22A P4SMA22CA 18.80 20.00 23.30 1 35.5 11.2 5 P4SMA24A P4SMA24CA 20.50 22.20 25.50 1 38.9 10.3 5 P4SMA27A P4SMA27CA 23.10 24.40 28.00 1 42.1 9.5 5 P4SMA30A P4SMA30CA 25.60 28.90 33.20 1 48.4 8.3 5 P4SMA33A P4SMA33CA 28.20 31.10 35.80 1 53.3 7.5 5 P4SMA36A P4SMA36CA 20.80 33.30 38.30 1 58.1 6.9 5 P4SMA39A P4SMA39CA 33.30 36.70 42.20 1 64.5 6.2 5 P4SMA43A P4SMA43CA 36.80 40.00 46.00 1 69.4 5.7 5 P4SMA47A P4SMA47CA 40.20 44.40 51.10 1 72.7 5.5 5 P4SMA51A P4SMA51CA 43.60 47.80 54.90 1 82.4 4.9 5 P4SMA56A P4SMA56CA 47.80 50.00 57.50 1 87.1 4.6 5 P4SMA62A P4SMA62CA 53.00 56.70 65.20 1 96.8 4.1 5 P4SMA68A P4SMA68CA 58.10 64.40 74.10 1 103.0 3.9 5 P4SMA75A P4SMA75CA 64.10 71.10 81.80 1 121.0 3.3 5 P4SMA82A P4SMA82CA 70.10 77.80 89.50 1 137.0 2.9 5 P4SMA91A P4SMA91CA 77.80 86.70 99.70 1 146.0 2.7 5 P4SMA100A P4SMA100CA 85.50 94.40 108.20 1 162.0 2.5 5 P4SMA110A P4SMA110CA 94.00 100.00 115.50 1 177.0 2.3 5 P4SMA120A P4SMA120CA 102.00 111.00 128.00 1 193.0 2.0 5 P4SMA130A P4SMA130CA 111.00 122.00 140.50 1 209.0 1.9 5 P4SMA150A P4SMA150CA 128.00 144.00 165.50 1 243.0 1.6 5 P4SMA180A P4SMA180CA 154.00 167.00 192.60 1 292.0 1.3 5 P4SMA200A P4SMA200CA 171.00 189.00 217.50 1 324.0 1.2 5 P4SMA220A P4SMA220CA 185.00 198.00 230.40 1 356.0 1.1 5 P4SMA250A P4SMA250CA 214.00 231.00 268.80 1 405.0 1.0 5 Circuit Protection System 800 Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:2 Transient Voltage Suppressors - P4SMA Series Ratings and Characteristic Curves Figure 1 - Peak Pulse Power Rating Curve Figure 2 - Pulse Derating Curve 100 Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % PPPM-Peak Pulse Power (kW) 10 1 0.2x0.2" (5.0x5.0mm) Copper Pad Area 0.1 0.000001 0.00001 0.0001 80 60 40 20 0 0.001 0 25 td-Pulse Width (sec.) Figure 3 - Pulse Waveform 75 100 125 150 175 Figure 4 - Typical Junction Capacitance 150 10000 t r =10µsec TJ =25°C 100 Bi-directional V=0V as the point where the peak current decays to 50% of I PPM Peak Value IPPM 1000 Cj (pF) IPPM- Peak Pulse Current, % I RSM 50 TA-Ambient temperature (ºC) Half Value IPPM IPPM ( ) Uni-directional V=0V Uni-directional @VR 100 Bi-directional @VR 2 50 10 10/1000µsec. Waveform 1 td 0 1.0 0 2.0 3.0 Tj=25ºC f=1.0MHz Vsig=50mVp-p 1.0 10.0 100.0 1000.0 VBR - Reverse Breakdown Voltage (V) 4.0 t-Time (ms) Figure 6 - Maximum Non-Repetitive Peak Forward Surge Current 1.2 45 IFSM - Peak Forward Surve Current (A) PM(AV), Steady State Power Dissipation (W) Figure 5 - Steady State Power Derating Curve 1 0.8 0.6 0.4 0.2 0 0 25 50 75 100 125 150 TA - Ambient Temperature (ºC) Circuit Protection System 175 40 35 30 25 20 15 10 5 0 1 10 100 Number of Cycles at 60 Hz Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:3 Transient Voltage Suppressors - P4SMA Series Soldering Parameters Feflow Condition Pre Heat Lead-free assembly - Temperature Min (T s(min)) 150°C - Temperature Max (T s(min)) 200°C - Time (min to max) (t s) 60-180 secs Average ramp up rate (Liquidus Temp (TL) to peak 3°C/second max TS(max) to TL - Ramp-up Rate 3°C/second max - Temperature (T L) (Liquidus) Reflow 217°C - Time (min to max) (t s) 60-150 seconds 260+0/-5 °C Peak Temperature (T P) Time within 5°C of actual peak Temperature (t p) 20-40 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (T P) 8 minutes Max. Do not exceed 280°C Physical Specifications tp TP one Ramp-up Temperature (T) TL tL Critical Z P TL to T Ts(max) Ts(min) Ramp-down ts Preheat Time (t) Circuit Protection System Weight 0.002 ounce,0.061 gram Case JEDEC DO-214AC molded plastic body over passivated junction. Polarity Color band denotes the cathode except Bipolar. Termina Matte Tin axial leads, solderable per JESD22-B102D. Environmental Specifications Temperature Cycle JESD22-A104 Pressure Cooker JESD 22-A102 High Temp. Storage JESD22-A103 HTRB JESD22-A108 Thermal Shock JESD22-A106 Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:4 Transient Voltage Suppressors - P4SMA Series Dimensions Unit:mm DO-214AC(SMA) DIM Inches Millimeters Min Max Min Max A 0.049 0.065 1.250 1.650 B 0.157 0.177 3.990 4.500 C 0.100 0.110 2.540 2.790 D 0.078 0.090 1.980 2.290 E 0.030 0.060 0.780 1.520 F - 0.008 - 0.203 G 0.194 0.208 4.930 5.280 H 0.006 0.012 0.152 0.305 I 0.070 - 1.800 - J 0.082 - 2.100 - K - 0.090 - 2.300 L 0.082 - 2.100 - Warehouse Storage Conditions of Products · Storage Conditions: 1. Storage Temperature: -10°C~+40°C 2. Relative Humidity:≤75%RH 3. Keep away from corrosive atmosphere and sunlight. · Period of Storage: 1 year Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:5 RuiLongYuan Electronics Co., Ltd. · Reproducing and modifying information of the document is prohibited without permission from Ruilongyuan International Inc. · Ruilongyuan International Inc. reserves the rights to make changes of the content herein the document anytime without notification. Please refer to our website for the latest document. · Ruilongyuan International Inc. disclaims any and all liability arising out of the application or use of any product including damages incidentally and consequentially occurred. · Ruilongyuan International Inc. does not assume any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. · Applications shown on the herein document are examples of standard use and operation. Customers are responsible in comprehending the suitable use in particular applications.Ruilongyuan International Inc. makes no representation or warranty that such applications will be suitable for the specifed use without further testing or modifcation. · The products shown herein are not designed and authorized for equipments requiring high level of reliability or relating to human life and for any applications concerning life-saving or life-sustaining, such as medical instruments, transportation equipment,aerospace machinery et cetera. Customers using or selling these products for use in such applications do so at their own risk and agree to fullyindemnify Ruilongyuan International Inc. for any damages resulting from such improper use or sale. Tel: +86-755-8290 8296 Circuit Protection System Fax: +86-755-8290 8002 E-mail: [email protected] Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:6