ELECTRONICS Transient Voltage Suppressors 1.5KE Series Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Transient Voltage Suppressors - 1.5KE Series Features UNI 1. Halogen-free 2. Rohs compliant 3. Typical maximum temperature coefficient 4. ΔVBR =0.1%xVBR@25°C x ΔT BI 5. Glass passivated Chip junction in DO-201 package 6. 1500W peak pulse capadility at 10x1000μs waveform,repetition rate (duty cycles):0.01% 7. Fast response time:typically less than 1.0ps from 0 Volts to BV min 8. Excellent clamping capability 9. Low incremental surge resistance 10. Typical IR less than 5μA above 11V 11. High temperature soldering guaranteed: 260°C/40 seconds / 0.375”, BI Cathode Anode (9.5mm) lead length, 5lbs., (2.3kg)tension 12. Plastic package has underwriters laboratory flammability classification 94v-0 UNI 13. Matte Tin Lead–free plated Applications TVS devices are ideal for the protection of I/O interfaces,VCC bus and other vulnerable circuits used in telecom, computer, industrial and consumer electronic applications. Mechanical Characteristics Rating Symbol Value Units PPPM 1500 Watts PD 6.5 Watts IFSM 200 Amps VF 3.5/5.0 V Operating junction and Storage Temperature Range. TJ,TSTG -55°C to 175°C °C Typical Thermal Resistance Junction to Lead RuJL 15 °C/W Typical Thermal Resistance Junction to Ambient RuJA 75 °C/W Reverse current IF 100 A Peak Pulse Power Dissipation by 10x1000μs test waveform (Fig.1)(Note 1) Steady State Power Dissipation on inifinite heat sink at TL=75°C (Fig. 5) Peak Forward Surge Current, 8.3ms Single Half Sine Wave Unidirectional only (Note 2) Maximum Instantaneous Forward Voltage at 25A for Unidirectional only (Note 3) Notes: 1. Non-repetitive current pulse , per Fig. 3 and derated above TA = 25°C per Fig. 2. 2. Measured on 8.3ms single half sine wave or equivalent square wave, duty cycle=4 perminute maximum. 3. VF<3.5V for devices of VBR _< 200V and VF<5.0V for devices of VBR _> 201V. Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:1 Transient Voltage Suppressors - 1.5KE Series Electriacl Characteristics Type Number Reverse StandOff Voltage Breakdown Voltage Min.@IT Test Current Maximum Clamping Voltage@IPP VC(V) Peak Pulse Current Reverse Leakage @VRWM 10.5 IPP(A) 144.8 IR(µA) 1000 (UNI) (BI) 1.5KE6.8A 1.5KE6.8CA VRWM(V) 5.80 VBR MIN.(V) 6.45 VBR.MAX.(V) 7.14 IT(mA) 10 1.5KE7.5A 1.5KE7.5CA 6.40 7.13 7.88 10 11.3 134.5 500 1.5KE8.2A 1.5KE8.2CA 7.02 7.79 8.61 10 12.1 125.6 200 1.5KE9.1A 1.5KE9.1CA 7.78 8.65 9.50 1 13.4 113.4 50 1.5KE10A 1.5KE10CA 8.55 9.50 10.50 1 14.5 104.8 10 1.5KE11A 1.5KE11CA 9.40 10.50 11.60 1 15.6 97.4 5 1.5KE12A 1.5KE12CA 10.20 11.40 12.60 1 16.7 91.0 5 1.5KE13A 1.5KE13CA 11.10 12.40 13.70 1 18.2 83.5 5 1.5KE15A 1.5KE15CA 12.80 14.30 15.80 1 21.2 71.7 5 1.5KE16A 1.5KE16CA 13.60 15.20 16.80 1 22.5 67.6 5 1.5KE18A 1.5KE18CA 15.30 17.10 18.90 1 25.2 60.3 5 1.5KE20A 1.5KE20CA 17.10 19.00 21.00 1 27.7 54.9 5 1.5KE22A 1.5KE22CA 18.80 20.90 23.10 1 30.6 49.7 5 1.5KE24A 1.5KE24CA 20.50 22.80 25.20 1 33.2 45.8 5 1.5KE27A 1.5KE27CA 23.10 25.70 28.40 1 37.5 40.5 5 1.5KE30A 1.5KE30CA 25.60 28.50 31.50 1 41.4 36.7 5 1.5KE33A 1.5KE33CA 28.20 31.40 34.70 1 45.7 33.3 5 1.5KE36A 1.5KE36CA 30.80 34.20 37.80 1 49.9 30.5 5 1.5KE39A 1.5KE39CA 33.30 37.10 41.00 1 53.9 28.2 5 1.5KE43A 1.5KE43CA 36.80 40.90 45.20 1 59.3 25.6 5 1.5KE47A 1.5KE47CA 40.20 44.70 49.40 1 64.8 23.5 5 1.5KE51A 1.5KE51CA 43.60 48.50 53.60 1 70.1 21.7 5 1.5KE56A 1.5KE56CA 47.80 53.20 58.80 1 77.0 19.7 5 1.5KE62A 1.5KE62CA 53.00 58.90 65.10 1 85.0 17.9 5 1.5KE68A 1.5KE68CA 58.10 64.60 71.40 1 92.0 16.5 5 1.5KE75A 1.5KE75CA 64.10 71.30 78.80 1 103.0 14.8 5 1.5KE82A 1.5KE82CA 70.10 77.90 86.10 1 113.0 13.5 5 1.5KE91A 1.5KE91CA 77.80 86.50 95.50 1 125.0 12.2 5 1.5KE100A 1.5KE100CA 85.50 95.00 105.00 1 137.0 11.1 5 1.5KE110A 1.5KE110CA 94.00 105.00 116.00 1 152.0 10.0 5 1.5KE120A 1.5KE120CA 102.00 114.00 126.00 1 165.0 9.20 5 1.5KE130A 1.5KE130CA 111.00 124.00 137.00 1 179.0 8.50 5 1.5KE150A 1.5KE150CA 128.00 143.00 158.00 1 207.0 7.30 5 1.5KE160A 1.5KE160CA 136.00 152.00 168.00 1 219.0 6.60 5 1.5KE170A 1.5KE170CA 145.00 162.00 179.00 1 234.0 6.50 5 1.5KE180A 1.5KE180CA 154.00 171.00 189.00 1 246.0 6.20 5 1.5KE200A 1.5KE200CA 171.00 190.00 210.00 1 274.0 5.50 5 1.5KE220A 1.5KE220CA 185.00 209.00 231.00 1 328.0 4.60 5 1.5KE250A 1.5KE250CA 214.00 237.00 263.00 1 344.0 4.40 5 1.5KE300A 1.5KE300CA 256.00 285.00 315.00 1 414.0 3.70 5 1.5KE350A 1.5KE400A 1.5KE440A 1.5KE350CA 1.5KE400CA 1.5KE440CA 300.00 342.00 376.00 332.00 380.00 418.00 368.00 420.00 462.00 1 1 1 482.0 548.0 602.0 3.20 2.80 2.50 5 5 5 1.5KE480A 1.5KE480CA 408.00 456.00 504.00 1 658.0 2.30 5 For bidirectional type having VR of 10 volts and less, the IR limit is double. For parts without A, the VBR is +10% and VC is 5% higher than with A parts. Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:2 Transient Voltage Suppressors - 1.5KE Series Ratings and Characteristic Curves Figure 1 - Peak Pulse Power Rating Curve Figure 2 - Pulse Derating Curve Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % PPPM-Peak Pulse Power (kW) 1000 100 10 1 0.1 0.000001 0.00001 0.0001 100 75 50 25 0 0.001 0 td-Pulse Width (Sec.) 100 125 150 175 200 100000 t r =10µsec TJ =25°C 100 Uni-directional V=0V Half Value IPPM IPPM ( ) 2 50 Bi-directional V=0V 10000 as the point where the peak current decays to 5 0% of I PPM Peak Value IPPM Cj (pF) IPPM- Peak Pulse Current, % I RSM 75 Figure 4 - Typical Junction Capacitance 150 1000 Uni-directional @ VR 100 Bi-directional @ VR 10/1000µsec. Waveform 10 td 1.0 0 2.0 3.0 Tj=25C f=1.0MHz Vsig=50mVp-p 1 1.0 4.0 100.0 1000.0 Figure 6 - Maximum Non-Repetitive Peak Forward Surge Current Uni-Directional Only Figure 5 - Steady State Power Derating Curve 6.5 6 5.5 5 4.5 4 3.5 3 2.5 2 1.5 1 0.5 0 10.0 VBR - Reverse Breakdown Voltage (V) t-Time (ms) 200 IFSM - Peak Forward Surge Current (A) Steady State Power Dissipation (W) 50 TA-Ambient Temperature (ºC) Figure 3 - Pulse Waveform 0 25 L = 0.375” (9.5mm) Lead Lengths 0 25 50 75 100 125 150 TL - Lead Temperature(ºC) Circuit Protection System 175 200 180 160 140 120 100 80 60 40 20 0 1 10 Number of Cycles at 60 Hz 100 Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:3 Transient Voltage Suppressors - 1.5KE Series Soldering Parameters Feflow Condition Pre Heat Lead-free assembly - Temperature Min (T s(min)) 150°C - Temperature Max (T s(min)) 200°C - Time (min to max) (t s) 60-180 secs Average ramp up rate (Liquidus Temp (TL) to peak 3°C/second max TS(max) to TL - Ramp-up Rate 3°C/second max - Temperature (T L) (Liquidus) Reflow 217°C - Time (min to max) (t s) 60-150 seconds 260+0/-5 °C Peak Temperature (T P) Time within 5°C of actual peak Temperature (t p) 20-40 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (T P) 8 minutes Max. Do not exceed 280°C Physical Specifications tp TP one Critical Z P TL to T Ramp-up Temperature (T) TL tL Ts(max) Ramp-down Ts(min) ts Preheat Time (t) Weight 0.045oz., 1.2g Case JEDEC DO-201 molded plastic body over passivated junction. Polarity Color band denotes the cathode except Bipolar. Termina Matte Tin axial leads, solderable per JESD22-B102D. Environmental Specifications Flow/Wave Soldering Temperature Cycle JESD22-A104 Pressure Cooker JESD 22-A102 Peak Temperature : 265°C High Temp. Storage JESD22-A103 Dipping Time : 10 seconds HTRB JESD22-A108 Soldering : 1 time Thermal Shock JESD22-A106 Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:4 Transient Voltage Suppressors - 1.5KE Series Part Numbering System 1.5KE xxx XX X OPTION CODE: BLANK Reel Tape -B Bulk Packaging TYPE CODE: A Uni-Directional (5% Voltage Tolerance) CA Bi-Directional VOLTAGE CODE (Refer to the Electrical Characteristics table) SERIES CODE Packaging Part Number Component Package Quantity Packaging Option Packaging Specification 1.5KExxxXX DO-201 1000 Tape & Reel ELA STD RS-296E 1.5KExxxXX-B DO-201 500 BULK Concord Packing Spec Warehouse Storage Conditions of Products · Storage Conditions: 1. Storage Temperature: -10°C~+40°C 2. Relative Humidity:≤75%RH 3. Keep away from corrosive atmosphere and sunlight. · Period of Storage: 1 year Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:5 RuiLongYuan Electronics Co., Ltd. · Reproducing and modifying information of the document is prohibited without permission from Ruilongyuan International Inc. · Ruilongyuan International Inc. reserves the rights to make changes of the content herein the document anytime without notification. Please refer to our website for the latest document. · Ruilongyuan International Inc. disclaims any and all liability arising out of the application or use of any product including damages incidentally and consequentially occurred. · Ruilongyuan International Inc. does not assume any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. · Applications shown on the herein document are examples of standard use and operation. Customers are responsible in comprehending the suitable use in particular applications.Ruilongyuan International Inc. makes no representation or warranty that such applications will be suitable for the specifed use without further testing or modifcation. · The products shown herein are not designed and authorized for equipments requiring high level of reliability or relating to human life and for any applications concerning life-saving or life-sustaining, such as medical instruments, transportation equipment,aerospace machinery et cetera. Customers using or selling these products for use in such applications do so at their own risk and agree to fullyindemnify Ruilongyuan International Inc. for any damages resulting from such improper use or sale. Tel: +86-755-8290 8296 Circuit Protection System Fax: +86-755-8290 8002 E-mail: [email protected] Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:6