ELECTRONICS Transient Voltage Suppressors P6SMB Series Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Transient Voltage Suppressors - P6SMB Series Features UNI 1. Halogen-free 2. Rohs compliant 3. Typical maximum temperature coefficient 4. ΔVBR = 0.1% x VBR@25°C x ΔT 5. Glass passivated Chip junction in DO-214AA package BI 6. 600W peak pulse capadility at 10×1000μs waveform, repetition rate(duty cycles):0.01% 7. Fast response time:typically less than 1.0ps from 0 Volts to BV min 8. Excellent clamping capability 9. Low incremental surge resistance 10 Typical IR less than 5μA above 12V BI Cathode 11. High temperature soldering guaranteed: 260°C/40 seconds / 0.375”, Anode 12. (9.5mm) lead length, 5lbs., (2.3kg) tension 13. Plastic package has underwriters laboratory flammability classification UNI 94v-0 Applications TVS devices are ideal for the protection of I/O interfaces,VCC bus and other vulnerable circuits used in telecom, computer, industrial and consumer electronic applications. Mechanical Characteristics Rating Symbol Value Units PPPM 600 Watts PD 5 Watts IFSM 100 Amps VF 3.5/5.0 V Operating junction and Storage Temperature Range. TJ,TSTG -55°C to 150°C °C Typical Thermal Resistance Junction to Lead RuJL 20 °C/W Typical Thermal Resistance Junction to Ambient RuJA 100 °C/W Peak Pulse Power Dissipation by 10x1000μs test waveform (Fig.1)(Note 1) Steady State Power Dissipation on inifinite heat sink at TL=75ºC (Fig. 5) Peak Forward Surge Current, 8.3ms Single Half Sine Wave Unidirectional only (Note 2) Maximum Instantaneous Forward Voltage at 25A for Unidirectional only (Note 3) Notes: 1. Non-repetitive current pulse , per Fig. 3 and derated above TA = 25°C per Fig. 2. 2. Mounted on copper pad area of 0.2x0.2” (5.0 x 5.0mm) to each terminal. 3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional device only, duty cycle=4 per minute maximum. 4. VF<3.5V for VBR < 200V and VF<5.0V for VBR > 201V. Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:1 Transient Voltage Suppressors - P6SMB Series Electriacl Characteristics Type Number (UNI) (BI) P6SMB6.8A P6SMB7.5A P6SMB8.2A P6SMB9.1A P6SMB10A P6SMB11A P6SMB12A P6SMB13A P6SMB15A P6SMB16A P6SMB18A P6SMB20A P6SMB22A P6SMB24A P6SMB27A P6SMB30A P6SMB33A P6SMB36A P6SMB39A P6SMB43A P6SMB47A P6SMB51A P6SMB56A P6SMB62A P6SMB68A P6SMB75A P6SMB82A P6SMB91A P6SMB100A P6SMB110A P6SMB120A P6SMB130A P6SMB150A P6SMB180A P6SMB200A P6SMB220A P6SMB250A P6SMB6.8CA P6SMB7.5CA P6SMB8.2CA P6SMB9.1CA P6SMB10CA P6SMB11CA P6SMB12CA P6SMB13CA P6SMB15CA P6SMB16CA P6SMB18CA P6SMB20CA P6SMB22CA P6SMB24CA P6SMB27CA P6SMB30CA P6SMB33CA P6SMB36CA P6SMB39CA P6SMB43CA P6SMB47CA P6SMB51CA P6SMB56CA P6SMB62CA P6SMB68CA P6SMB75CA P6SMB82CA P6SMB91CA P6SMB100CA P6SMB110CA P6SMB120CA P6SMB130CA P6SMB150CA P6SMB180CA P6SMB200CA P6SMB220CA P6SMB250CA Reverse StandOff Voltage Breakdown Voltage@IT Test Current VRWM(V) 5.80 6.40 7.02 7.78 8.55 9.40 10.20 11.10 12.80 13.60 15.30 17.10 18.80 20.50 23.10 25.60 28.20 20.80 33.30 36.80 40.20 43.60 47.80 53.00 58.10 64.10 70.10 77.80 85.50 94.00 102.00 111.00 128.00 154.00 171.00 185.00 214.00 VBR MIN.(V) VBR MAX.(V) 6.40 7.25 7.22 8.30 7.78 8.95 8.33 9.58 9.44 10.82 10.00 11.50 11.10 12.80 12.20 14.00 14.40 16.50 15.60 17.90 16.70 19.20 18.90 21.70 20.00 23.30 22.20 25.50 24.40 28.00 28.90 33.20 31.10 35.80 33.30 38.30 36.70 42.20 40.00 46.00 44.40 51.10 47.80 54.90 50.00 57.50 56.70 65.20 64.40 74.10 71.10 81.80 77.80 89.50 86.70 99.70 94.40 108.20 100.00 115.50 111.00 128.00 122.00 140.50 144.00 165.50 167.00 192.60 189.00 217.50 209.00 243.20 231.00 268.80 IT (mA) 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Circuit Protection System Maximum Clamping Voltage@IPP VC (V) 9.2 10.3 12.0 12.9 13.6 18.2 19.9 21.5 24.4 26.0 29.2 32.4 35.5 38.9 42.1 48.4 53.3 58.1 64.5 69.4 72.7 82.4 87.1 96.8 103.0 121.0 137.0 146.0 162.0 177.0 193.0 209.0 243.0 292.0 324.0 356.0 405.0 Peak Pulse Current IPP (A) 65.2 58.3 50.0 46.6 44.1 33.0 30.2 27.9 24.6 23.1 20.5 18.5 16.9 15.2 14.2 12.4 11.3 10.3 9.3 8.6 8.3 7.3 6.9 6.2 5.8 4.9 4.4 4.1 3.7 3.4 3.1 2.9 2.5 2.1 1.9 1.7 1.5 Reverse Leakage @VRWM IR(µA) 800 800 200 100 50 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:2 Transient Voltage Suppressors - P6SMB Series Ratings and Characteristic Curves Figure 1 - Peak Pulse Power Rating Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % PPPM-Peak Pulse Power (kW) 100 Figure 2 - Pulse Derating Curve A 10 1 0.2x0.2" (5.0x5.0mm) Copper Pad Area 0.1 0.000001 0.00001 0.0001 100 80 60 40 20 0 0.001 0 td-Pulse Width (sec.) TJ =25°C 125 150 175 100 Bi-directional V=0V as the point where the peak current decays to 5 0% of I PPM Peak Value IPPM 1000 Half Value IPPM IPPM ( ) 2 50 100 Bi-directional @VR 10/1000µsec. Waveform 10 Tj=25C f=1.0MHz Vsig=50mVp-p td 1.0 0 Uni-directional V=0V Uni-directional @VR Cj (pF) IPPM- Peak Pulse Current, % I RSM 100 10000 t r =10µsec 2.0 3.0 1 1.0 4.0 t-Time (ms) Figure 5 - Steady State Power Derating Curve 10.0 100.0 VBR - Reverse Breakdown Voltage (V) 1000.0 Figure 6 - Maximum Non-Repetitive Peak Forward Surge Current Uni-Directional Only 6 120 IFSM - Peak Forward Surge Current (A) PM(AV), Steady State Power Dissipation (W) 75 Figure 4 - Typical Junction Capacitance 150 5 4 3 2 1 0 50 TA - Ambient Temperature (ºC) Figure 3 - Pulse Waveform 0 25 0 25 50 75 100 125 TA - Ambient Temperature (ºC) Circuit Protection System 150 175 100 80 60 40 20 0 1 10 100 Number of Cycles at 60 Hz Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:3 Transient Voltage Suppressors - P6SMB Series Soldering Parameters Feflow Condition Pre Heat Lead-free assembly - Temperature Min (T s(min)) 150°C - Temperature Max (T s(min)) 200°C - Time (min to max) (t s) 60-180 secs Average ramp up rate (Liquidus Temp (TL) to peak 3°C/second max TS(max) to TL - Ramp-up Rate 3°C/second max - Temperature (T L) (Liquidus) Reflow 217°C - Time (min to max) (t s) 60-150 seconds 260+0/-5 °C Peak Temperature (T P) Time within 5°C of actual peak Temperature (t p) 20-40 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (T P) 8 minutes Max. Do not exceed 280°C Physical Specifications tp TP one Ramp-up Temperature (T) TL tL Critical Z P TL to T Weight 0.003 ounce, 0.093 grams JEDEC DO214AA. Molded plastic body over glass passivated junction Color band denotes cathode except Bidirectional. Matte Tin-plated leads, Solderable per JESD22-B102D Case Ts(max) Ts(min) Ramp-down ts Polarity Termina Preheat Time (t) Circuit Protection System Environmental Specifications Temperature Cycle JESD22-A104 Pressure Cooker JESD 22-A102 High Temp. Storage JESD22-A103 HTRB JESD22-A108 Thermal Shock JESD22-A106 Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:4 Transient Voltage Suppressors - P6SMB Series Dimensions Unit:mm DO-214AA (SMB J-Bend) Inches DIM Millimeters Min Max Min Max A 0.077 0.086 1.950 2.200 B 0.160 0.180 4.060 4.570 C 0.130 0.155 3.300 3.940 D 0.084 0.096 2.130 2.440 E 0.030 0.060 0.760 1.520 F - 0.008 - 0.203 G 0.205 0.220 5.210 5.590 H 0.006 0.012 0.152 0.305 I 0.089 - 2.260 - J 0.085 - 2.160 - K - 0.107 - 2.740 L 0.085 - 2.160 - Part Numbering System P6SMB XXX C A 5% VOLTAGE TOLERANCE BI-DIRECTIONAL VOLTAGE SERIES Warehouse Storage Conditions of Products · Storage Conditions: 1. Storage Temperature: -10°C~+40°C 2. Relative Humidity:≤75%RH 3. Keep away from corrosive atmosphere and sunlight. · Period of Storage: 1 year Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:5 RuiLongYuan Electronics Co., Ltd. · Reproducing and modifying information of the document is prohibited without permission from Ruilongyuan International Inc. · Ruilongyuan International Inc. reserves the rights to make changes of the content herein the document anytime without notification. Please refer to our website for the latest document. · Ruilongyuan International Inc. disclaims any and all liability arising out of the application or use of any product including damages incidentally and consequentially occurred. · Ruilongyuan International Inc. does not assume any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. · Applications shown on the herein document are examples of standard use and operation. Customers are responsible in comprehending the suitable use in particular applications.Ruilongyuan International Inc. makes no representation or warranty that such applications will be suitable for the specifed use without further testing or modifcation. · The products shown herein are not designed and authorized for equipments requiring high level of reliability or relating to human life and for any applications concerning life-saving or life-sustaining, such as medical instruments, transportation equipment,aerospace machinery et cetera. Customers using or selling these products for use in such applications do so at their own risk and agree to fullyindemnify Ruilongyuan International Inc. for any damages resulting from such improper use or sale. Tel: +86-755-8290 8296 Circuit Protection System Fax: +86-755-8290 8002 E-mail: [email protected] Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:6