ELECTRONICS Transient Voltage Suppressors 3KP Series Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Transient Voltage Suppressors - 3KP Series Features UNI 1. Halogen-free 2. Rohs compliant 3. Typical maximum temperature coefficient 4. ΔVBR =0.1%xVBR@25°C x ΔT BI 5. Glass passivated Chip junction in P600 package 6. 3000W peak pulse capadility at 10x1000μs waveform,repetition rate (duty cycles):0.01% 7. Fast response time:typically less than 1.0ps from 0 Volts to BV min 8. Excellent clamping capability 9. Low incremental surge resistance 10. Typical IR less than 3μA above 11V BI Cathode 11. High temperature soldering guaranteed: 260°C/40 seconds / 0.375”, Anode (9.5mm) lead length, 5lbs., (2.3kg) tension 12. Plastic package has underwriters laboratory flammability classification UNI 94v-0 Applications TVS devices are ideal for the protection of I/O interfaces,VCC bus and other vulnerable circuits used in telecom, computer, industrial and consumer electronic applications. Mechanical Characteristics Rating Symbol Value Units PPPM 3000 Watts PD 7.0 Watts IFSM 300 Amps VF 3.5/5.0 V Operating junction and Storage Temperature Range. TJ,TSTG -55°C to 175°C °C Typical Thermal Resistance Junction to Lead RuJL 8.0 °C/W Typical Thermal Resistance Junction to Ambient RuJA 40 °C/W Peak Pulse Power Dissipation by 10x1000μs test waveform (Fig.1)(Note 1) Steady State Power Dissipation on inifinite heat sink at TL=75°C (Fig. 5) Peak Forward Surge Current, 8.3ms Single Half Sine Wave Unidirectional only (Note 2) Maximum Instantaneous Forward Voltage at 25A for Unidirectional only (Note 3) Notes: 1. Non-repetitive current pulse , per Fig. 3 and derated above TA = 25°C per Fig. 2. 2. Measured on 8.3ms single half sine wave or equivalent square wave, duty cycle=4 perminute maximum. Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:1 Electriacl Characteristics Reverse StandOff Voltage Type Number Breakdown Voltage Min.@IT Test Current (UNI) (BI) 3KP5.0A 3KP5.0CA VRWM(V) 5.0 VBR MIN.(V) 6.40 VBR.MAX.(V) 7.00 IT(mA) 50 3KP6.0A 3KP6.0CA 6.0 6.67 7.37 3KP6.5A 3KP6.5CA 6.5 7.22 3KP7.0A 3KP7.0CA 7.0 3KP7.5A 3KP7.5CA 3KP8.0A Maximum Clamping Voltage@IPP VC(V) Peak Pulse Current Reverse Leakage @VRWM IR(µA) 9.2 IPP(A) 326.1 50 10.3 291.3 5000 7.98 50 11.2 267.9 2000 7.78 8.60 50 12.0 250.0 1000 7.5 8.33 9.21 5 12.9 232.6 250 3KP8.0CA 8.0 8.89 9.83 5 13.6 220.6 150 3KP8.5A 3KP8.5CA 8.5 9.44 10.40 5 14.4 208.3 50 3KP9.0A 3KP9.0CA 9.0 10.00 11.10 5 15.4 194.8 20 3KP10A 3KP10CA 10.0 11.10 12.30 5 17.0 176.5 15 3KP11A 3KP11CA 11.0 12.20 13.50 5 18.2 164.8 5 3KP12A 3KP12CA 12.0 13.30 14.70 5 19.9 150.8 5 3KP13A 3KP13CA 13.0 14.40 15.90 5 21.5 139.5 5 3KP14A 3KP14CA 14.0 15.60 17.20 5 23.2 129.3 5 3KP15A 3KP15CA 15.0 16.70 18.50 5 24.4 123.0 5 3KP16A 3KP16CA 16.0 17.80 19.70 5 26.0 115.4 5 3KP17A 3KP17CA 17.0 18.90 20.90 5 27.6 108.7 5 3KP18A 3KP18CA 18.0 20.00 22.10 5 29.2 102.7 5 3KP20A 3KP20CA 20.0 22.20 24.50 5 32.4 92.6 5 3KP22A 3KP22CA 22.0 24.40 26.90 5 35.5 84.5 5 3KP24A 3KP24CA 24.0 26.70 29.50 5 38.9 77.1 5 3KP26A 3KP26CA 26.0 28.90 31.90 5 42.1 71.3 5 3KP28A 3KP28CA 28.0 31.10 34.40 5 45.4 66.1 5 3KP30A 3KP30CA 30.0 33.30 36.80 5 48.4 62.0 5 3KP33A 3KP33CA 33.0 36.70 40.60 5 53.3 56.3 5 3KP36A 3KP36CA 36.0 40.00 44.20 5 58.1 51.6 5 3KP40A 3KP40CA 40.0 44.40 49.10 5 64.5 46.5 5 3KP43A 3KP43CA 43.0 47.80 52.80 5 69.4 43.2 5 3KP45A 3KP45CA 45.0 50.00 55.30 5 72.7 41.3 5 3KP48A 3KP48CA 48.0 53.30 58.90 5 77.4 38.8 5 3KP51A 3KP51CA 51.0 56.70 62.70 5 82.4 36.4 5 3KP54A 3KP54CA 54.0 60.00 66.30 5 87.1 34.4 5 3KP58A 3KP58CA 58.0 64.40 71.20 5 93.6 32.1 5 3KP60A 3KP60CA 60.0 66.70 73.70 5 96.8 31.0 5 3KP64A 3KP64CA 64.0 71.10 78.60 5 103.0 29.1 5 3KP70A 3KP70CA 70.0 77.80 86.00 5 113.0 26.5 5 3KP75A 3KP75CA 75.0 83.30 92.10 5 121.0 24.8 5 3KP78A 3KP78CA 78.0 86.70 95.80 5 126.0 23.8 5 3KP85A 3KP85CA 85.0 94.40 104.00 5 137.0 21.9 5 3KP90A 3KP90CA 90.0 100.00 111.00 5 146.0 20.5 5 3KP100A 3KP100CA 100.0 111.00 123.00 5 162.0 18.5 5 3KP110A 3KP110CA 110.0 122.00 135.00 5 177.0 16.9 5 3KP120A 3KP120CA 120.0 133.00 147.00 5 193.0 15.5 5 3KP130A 3KP130CA 130.0 144.00 159.00 5 209.0 14.4 5 3KP150A 3KP150CA 150.0 167.00 185.00 5 243.0 12.3 5 3KP160A 3KP160CA 160.0 178.00 197.00 5 259.0 11.6 5 3KP170A 3KP170CA 170.0 189.00 209.00 5 275.0 10.9 5 3KP180A 3KP180CA 180.0 200.00 221.00 5 292.0 10.4 5 3KP190A 3KP190CA 190.0 211.00 233.00 5 308.0 9.7 5 3KP200A 3KP200CA 200.0 222.00 246.00 5 324.2 9.1 5 3KP210A 3KP210CA 210.0 233.00 258.00 5 340.5 8.6 5 3KP220A 3KP220CA 220.0 244.00 270.00 5 371.1 8.1 5 5000 For parts without A , the VBR is ± 10% and VC is 5% higher than with A parts For bidirectional type having VR of 10 volts and less, the IR limit is double. Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:2 Transient Voltage Suppressors - 3KP Series Ratings and Characteristic Curves Figure 1 - Peak Pulse Power Rating Curve Figure 2 - Pulse Derating Curve Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % PPPM-Peak Pulse Power (kW) 1000 100 10 1 0.1 0.000001 0.00001 0.0001 100 75 50 25 0 0.001 0 25 td-Pulse Width (Sec.) 175 200 TJ =25°C 100 Uni-directional V=0V Half Value IPPM IPPM ( ) 2 50 Bi-directional V=0V 10000 as the point where the peak current decays to 5 0% of I PPM Peak Value IPPM Cj (pF) IPPM- Peak Pulse Current, % I RSM 125 150 100000 t r =10µsec 1000 Uni-directional @ VR 100 Bi-directional @ VR 10/1000µsec. Waveform 10 td 1.0 0 2.0 3.0 Tj=25C f=1.0MHz Vsig=50mVp-p 1 1.0 4.0 10.0 100.0 1000.0 VBR - Reverse Breakdown Voltage (V) t-Time (ms) Figure 6 - Maximum Non-Repetitive Peak Forward Surge Current Uni-Directional Only Figure 5 - Steady State Power Derating Curve 200 IFSM - Peak Forward Surge Current (A) Steady State Power Dissipation (W) 100 Figure 4 - Typical Junction Capacitance 150 6.5 6 5.5 5 4.5 4 3.5 3 2.5 2 1.5 1 0.5 0 75 TA-Ambient Temperature (ºC) Figure 3 - Pulse Waveform 0 50 L = 0.375” (9.5mm) Lead Lengths 0 25 50 75 100 125 150 TL - Lead Temperature(ºC) Circuit Protection System 175 200 180 160 140 120 100 80 60 40 20 0 1 10 Number of Cycles at 60 Hz 100 Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:3 Transient Voltage Suppressors - 3KP Series Soldering Parameters Feflow Condition Pre Heat Lead-free assembly - Temperature Min (T s(min)) 150°C - Temperature Max (T s(min)) 200°C - Time (min to max) (t s) 60-180 secs Average ramp up rate (Liquidus Temp (TL) to peak 3°C/second max TS(max) to TL - Ramp-up Rate 3°C/second max - Temperature (T L) (Liquidus) Reflow 217°C - Time (min to max) (t s) 60-150 seconds 260+0/-5 °C Peak Temperature (T P) Time within 5°C of actual peak Temperature (t p) 20-40 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (T P) 8 minutes Max. Do not exceed 280°C Physical Specifications tp TP one Critical Z P TL to T Ramp-up Temperature (T) TL tL Ts(max) Ramp-down Ts(min) ts Preheat Time (t) Weight 0.045oz., 1.2g Case JEDEC DO-201 molded plastic body over passivated junction. Polarity Color band denotes the cathode except Bipolar. Termina Matte Tin axial leads, solderable per JESD22-B102D. Environmental Specifications Flow/Wave Soldering Temperature Cycle JESD22-A104 Pressure Cooker JESD 22-A102 Peak Temperature : 265°C High Temp. Storage JESD22-A103 Dipping Time : 10 seconds HTRB JESD22-A108 Soldering : 1 time Thermal Shock JESD22-A106 Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:4 Transient Voltage Suppressors - 3KP Series Dimensions Unit:mm D Inches DIM C A A B P600 Millimeters Min Max Min Max A 1.000 - 25.40 - B 0.340 0.360 8.60 9.10 C 0.048 0.052 1.22 1.32 D 0.340 0.360 8.60 9.10 Part Numbering System 3KP XXX C A 5% VOLTAGE TOLERANCE BI-DIRECTIONAL STAND OFF VOLTAGE SERIES Packaging Part Number Component Package Quantity Packaging Option Packaging Specification 3KPxxxXX P600 400 Tape & Reel ELA STD RS-296E 3KPxxxXX-B P600 100 BULK Concord Packing Spec Warehouse Storage Conditions of Products · Storage Conditions: 1. Storage Temperature: -10°C~+40°C 2. Relative Humidity:≤75%RH 3. Keep away from corrosive atmosphere and sunlight. · Period of Storage: 1 year Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:5 RuiLongYuan Electronics Co., Ltd. · Reproducing and modifying information of the document is prohibited without permission from Ruilongyuan International Inc. · Ruilongyuan International Inc. reserves the rights to make changes of the content herein the document anytime without notification. Please refer to our website for the latest document. · Ruilongyuan International Inc. disclaims any and all liability arising out of the application or use of any product including damages incidentally and consequentially occurred. · Ruilongyuan International Inc. does not assume any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. · Applications shown on the herein document are examples of standard use and operation. Customers are responsible in comprehending the suitable use in particular applications.Ruilongyuan International Inc. makes no representation or warranty that such applications will be suitable for the specifed use without further testing or modifcation. · The products shown herein are not designed and authorized for equipments requiring high level of reliability or relating to human life and for any applications concerning life-saving or life-sustaining, such as medical instruments, transportation equipment,aerospace machinery et cetera. Customers using or selling these products for use in such applications do so at their own risk and agree to fullyindemnify Ruilongyuan International Inc. for any damages resulting from such improper use or sale. Tel: +86-755-8290 8296 Circuit Protection System Fax: +86-755-8290 8002 E-mail: [email protected] Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:6