LM62 2.7V, 15.6 mV/˚C SOT-23 Temperature Sensor General Description Features The LM62 is a precision integrated-circuit temperature sensor that can sense a 0˚C to +90˚C temperature range while operating from a single +3.0V supply. The LM62’s output voltage is linearly proportional to Celsius (Centigrade) temperature (+15.6 mV/˚C) and has a DC offset of +480 mV. The offset allows reading temperatures down to 0˚C without the need for a negative supply. The nominal output voltage of the LM62 ranges from +480 mV to +1884 mV for a 0˚C to +90˚C temperature range. The LM62 is calibrated to provide accuracies of ± 2.0˚C at room temperature and +2.5˚C/ −2.0˚C over the full 0˚C to +90˚C temperature range. n Calibrated linear scale factor of +15.6 mV/˚C n Rated for full 0˚C to +90˚C range with 3.0V supply n Suitable for remote applications The LM62’s linear output, +480 mV offset, and factory calibration simplify external circuitry required in a single supply environment where reading temperatures down to 0˚C is required. Because the LM62’s quiescent current is less than 130 µA, self-heating is limited to a very low 0.2˚C in still air. Shutdown capability for the LM62 is intrinsic because its inherent low power consumption allows it to be powered directly from the output of many logic gates. Connection Diagram Applications n n n n n n n n n Cellular Phones Computers Power Supply Modules Battery Management FAX Machines Printers HVAC Disk Drives Appliances Key Specifications n n n n n n Accuracy at 25˚C Temperature Slope Power Supply Voltage Range Current Drain @ 25˚C Nonlinearity Output Impedance ± 2.0 or ± 3.0˚C (max) +15.6 mV/˚C +2.7V to +10V 130 µA (max) ± 0.8˚C (max) 4.7 kΩ (max) Typical Application SOT-23 10089301 Top View See NS Package Number mf03a 10089302 VO = (+15.6 mV/˚C x T˚C) + 480 mV Ordering Information Order Device Number Top Mark Supplied As Temperature (T) Typical VO +90˚C +1884 mV +70˚C +1572 mV LM62BIM3 T7B 1000 Units, Tape and Reel +25˚C 870 mV LM62BIM3X T7B 3000 Units, Tape and Reel 0˚C +480 mV LM62CIM3 T7C 1000 Units, Tape and Reel LM62CIM3X T7C 3000 Units, Tape and Reel © 2005 National Semiconductor Corporation DS100893 FIGURE 1. Full-Range Centigrade Temperature Sensor (0˚C to +90˚C) Stabilizing a Crystal Oscillator www.national.com LM62 2.7V, 15.6 mV/˚C, SOT-23 Temperature Sensor August 2005 LM62 Absolute Maximum Ratings (Note 1) Supply Voltage +12V to −0.2V Output Voltage (+VS + 0.6V) to −0.6V Output Current 10 mA Input Current at any pin (Note 2) Storage Temperature Machine Model Operating Ratings(Note 1) Specified Temperature Range: 5 mA TMIN ≤ TA ≤ TMAX 0˚C ≤ TA ≤ +90˚C LM62B, LM62C −65˚C to +150˚C Junction Temperature, max (TJMAX) 250V Supply Voltage Range (+VS) +2.7V to +10V Thermal Resistance, θJA(Note 5) 450˚C/W +125˚C Soldering process must comply with National Semiconductor’s Reflow Temperature Profile specifications. Refer to www.national.com/packaging. (Note 4) ESD Susceptibility (Note 3) : Human Body Model 2500V Electrical Characteristics Unless otherwise noted, these specifications apply for +VS = +3.0 VDC. Boldface limits apply for TA = TJ = TMIN to TMAX ; all other limits TA = TJ = 25˚C. Parameter Conditions Typical (Note 6) LM62B LM62C Limits Limits (Note 7) (Note 7) ± 2.0 ± 3.0 ˚C (max) +2.5/−2.0 +4.0/−3.0 ˚C (max) ± 0.8 ± 1.0 ˚C (max) +16.1 +16.3 mV/˚C (max) +15.1 +14.9 mV/˚C (min) +3.0V ≤ +VS ≤ +10V 4.7 4.7 0˚C ≤ TA ≤ +75˚C, +VS= +2.7V 4.4 4.4 ± 1.13 ± 9.7 ± 1.13 ± 9.7 mV/V (max) 130 130 µA (max) 165 165 µA (max) Accuracy (Note 8) Output Voltage at 0˚C +480 Nonlinearity (Note 9) Sensor Gain +16 (Average Slope) Output Impedance Line Regulation (Note 10) Units (Limit) +3.0V ≤ +VS ≤ +10V +2.7V ≤ +VS ≤ +3.3V, 0˚C ≤ TA ≤ +75˚C mV kΩ (max) kΩ (max) mV (max) Quiescent Current +2.7V ≤ +VS ≤ +10V 82 Change of Quiescent Current +2.7V ≤ +VS ≤ +10V ±5 µA 0.2 µA/˚C ± 0.2 ˚C Temperature Coefficient of Quiescent Current Long Term Stability (Note 11) TJ=TMAX=+100˚C, for 1000 hours Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. Note 2: When the input voltage (VI) at any pin exceeds power supplies (VI < GND or VI > +VS), the current at that pin should be limited to 5 mA. Note 3: The human body model is a 100 pF capacitor discharged through a 1.5 kΩ resistor into each pin. The machine model is a 200 pF capacitor discharged directly into each pin. Note 4: Reflow temperature profiles are different for lead-free and non-lead-free packages. Note 5: The junction to ambient thermal resistance (θJA) is specified without a heat sink in still air. Note 6: Typicals are at TJ = TA = 25˚C and represent most likely parametric norm. Note 7: Limits are guaranteed to National’s AOQL (Average Outgoing Quality Level). Note 8: Accuracy is defined as the error between the output voltage and +15.6 mV/˚C times the device’s case temperature plus 480 mV, at specified conditions of voltage, current, and temperature (expressed in ˚C). Note 9: Nonlinearity is defined as the deviation of the output-voltage-versus-temperature curve from the best-fit straight line, over the device’s rated temperature range. Note 10: Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes in output due to heating effects can be computed by multiplying the internal dissipation by the thermal resistance. Note 11: For best long-term stability, any precision circuit will give best results if the unit is aged at a warm temperature, and/or temperature cycled for at least 46 hours before long-term life test begins. This is especially true when a small (Surface-Mount) part is wave-soldered; allow time for stress relaxation to occur. The majority of the drift will occur in the first 1000 hours at elevated temperatures. The drift after 1000 hours will not continue at the first 1000 hour rate. www.national.com 2 To generate these curves the LM62 was mounted to a Thermal Resistance Junction to Air Thermal Time Constant 10089303 10089304 Thermal Response in Stirred Oil Bath with Heat Sink Thermal Response in Still Air with Heat Sink 10089305 10089306 Thermal Response in Still Air without a Heat Sink Quiescent Current vs. Temperature 10089309 10089308 3 www.national.com LM62 Typical Performance Characteristics printed circuit board as shown in Figure 2. LM62 Typical Performance Characteristics To generate these curves the LM62 was mounted to a printed circuit board as shown in Figure 2. (Continued) Accuracy vs Temperature Noise Voltage 10089310 10089311 Supply Voltage vs Supply Current Start-Up Response 10089322 10089312 Circuit Board 10089314 Printed Circuit Board Used for Heat Sink to Generate All Curves. 1⁄2" Square Printed Circuit Board with 2 oz. Copper Foil or Similar. FIGURE 2. www.national.com 4 LM62 1.0 Mounting 2.0 Capacitive Loads The LM62 can be applied easily in the same way as other integrated-circuit temperature sensors. It can be glued or cemented to a surface. The temperature that the LM62 is sensing will be within about +0.2˚C of the surface temperature that LM62’s leads are attached to. This presumes that the ambient air temperature is almost the same as the surface temperature; if the air temperature were much higher or lower than the surface temperature, the actual temperature measured would be at an intermediate temperature between the surface temperature and the air temperature. The LM62 handles capacitive loading well. Without any special precautions, the LM62 can drive any capacitive load as shown in Figure 4. Over the specified temperature range the LM62 has a maximum output impedance of 4.7 kΩ. In an extremely noisy environment it may be necessary to add some filtering to minimize noise pickup. It is recommended that 0.1 µF be added from +VS to GND to bypass the power supply voltage, as shown in Figure 5. In a noisy environment it may be necessary to add a capacitor from the output to ground. A 1 µF output capacitor with the 4.7 kΩ maximum output impedance will form a 34 Hz lowpass filter. Since the thermal time constant of the LM62 is much slower than the 30 ms time constant formed by the RC, the overall response time of the LM62 will not be significantly affected. For much larger capacitors this additional time lag will increase the overall response time of the LM62. To ensure good thermal conductivity the backside of the LM62 die is directly attached to the GND pin. The lands and traces to the LM62 will, of course, be part of the printed circuit board, which is the object whose temperature is being measured. These printed circuit board lands and traces will not cause the LM62’s temperature to deviate from the desired temperature. Alternatively, the LM62 can be mounted inside a sealed-end metal tube, and can then be dipped into a bath or screwed into a threaded hole in a tank. As with any IC, the LM62 and accompanying wiring and circuits must be kept insulated and dry, to avoid leakage and corrosion. This is especially true if the circuit may operate at cold temperatures where condensation can occur. Printed-circuit coatings and varnishes such as Humiseal and epoxy paints or dips are often used to ensure that moisture cannot corrode the LM62 or its connections. The thermal resistance junction to ambient (θJA) is the parameter used to calculate the rise of a device junction temperature due to its power dissipation. For the LM62 the equation used to calculate the rise in the die temperature is as follows: TJ = TA + θJA [(+VS IQ) + (+VS − VO) IL] where IQ is the quiescent current and ILis the load current on the output. Since the LM62’s junction temperature is the actual temperature being measured care should be taken to minimize the load current that the LM62 is required to drive. 10089315 FIGURE 4. LM62 No Decoupling Required for Capacitive Load 10089316 FIGURE 5. LM62 with Filter for Noisy Environment The table shown in Figure 3 summarizes the rise in die temperature of the LM62 without any loading, and the thermal resistance for different conditions. Still air SOT-23 SOT-23 no heat sink small heat fin (Note 13) (Note 12) θJA TJ − T A θJA TJ − T A (˚C/W) (˚C) (˚C/W) (˚C) 450 0.17 260 0.1 180 0.07 Moving air Note 12: Heat sink used is 1⁄2" square printed circuit board with 2 oz. foil with part attached as shown in Figure 2 . Note 13: Part soldered to 30 gauge wire. FIGURE 3. Temperature Rise of LM62 Due to Self-Heating and Thermal Resistance (θJA) 5 www.national.com LM62 2.0 Capacitive Loads (Continued) 10089317 FIGURE 6. Simplified Schematic 3.0 Applications Circuits 10089318 FIGURE 7. Centigrade Thermostat 10089319 FIGURE 8. Conserving Power Dissipation with Shutdown www.national.com 6 LM62 2.7V, 15.6 mV/˚C, SOT-23 Temperature Sensor Physical Dimensions inches (millimeters) unless otherwise noted SOT-23 Molded Small Outline Transistor Package (M3) Order Number LM62BIM3 or LM62CIM3 NS Package Number mf03a National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2. Leadfree products are RoHS compliant. National Semiconductor Americas Customer Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: [email protected] National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: [email protected] Tel: 81-3-5639-7560