TALEMA W83L771ASG

W83L771AWG
W83L771ASG
Nuvoton
H/W Monitoring IC
DATE: NOVEMBER 19TH, 2009
REVISION: 1.91
TABLE OF CONTENTS1.
2.
3.
4.
5.
6.
7.
GENERAL DESCRIPTION ......................................................................................................... 1
1.1
Product Selection Guide ................................................................................................. 1
FEATURES ................................................................................................................................. 2
2.1
Monitoring Items - Temperature ..................................................................................... 2
2.2
General Features ............................................................................................................ 2
2.3
Package Type ................................................................................................................. 2
2.4
Applications..................................................................................................................... 2
KEY SPECIFICATIONS .............................................................................................................. 3
BLOCK DIAGRAM ...................................................................................................................... 3
PIN CONFIGURATION ............................................................................................................... 4
PIN DESCRIPTION ..................................................................................................................... 4
FUNCTIONAL DESCRIPTION.................................................................................................... 5
7.1
General Description ........................................................................................................ 5
7.2
Access Interface ............................................................................................................. 6
7.2.1
7.2.2
7.3
ALERT Output Mode ...................................................................................................... 7
7.3.1
ALERT Output Comparator Mode ................................................................................... 7
7.3.2
ALERT Output Interrupt Mode ........................................................................................ 8
7.3.3
ALERT Output SMBusTM ALERT Mode ........................................................................ 9
7.4
T _ CRIT _ A Output and T_CRIT flags .......................................................................... 10
7.5
Measured Temperature Data Format ........................................................................... 11
7.5.1
7.5.2
8.
9.
10.
Serial bus write to internal address register followed by the data byte ............................. 6
Serial bus read form internal address register followed by the data byte ......................... 6
Measure Remote Temperature Data Format .................................................................. 11
Measure Local Temperature Data Format...................................................................... 11
7.6
Digital Filter ................................................................................................................... 12
7.7
Fault Detect ................................................................................................................... 13
7.8
Conversion Rate and Moving Average ......................................................................... 13
CONTROL AND STATUS REGISTER ..................................................................................... 14
8.1
W83L771AWG/ASG Registers ..................................................................................... 14
8.2
Data Format of Temperature Registers (LT, RTHB, RTLB, LHS, RHSHB, RHSLB, LLS,
RLSHB, RLSLB, RTOHB, RTOLB, RCS, LCS) ........................................................................ 15
8.3
Status Register (SR) ..................................................................................................... 16
8.4
Configuration Register (C) ............................................................................................ 16
8.5
T_CRIT Hysteresis Register (TH) ................................................................................. 17
8.6
Conversion Rate Register (CR) .................................................................................... 17
8.7
Filter and Alert Configure Register (RDTF) .................................................................. 18
8.8
Ideality (IDEA) ............................................................................................................... 18
ELECTRICAL CHARACTERISTIC ........................................................................................... 19
9.1
Absolute Maximum Ratings .......................................................................................... 19
9.2
DC Characteristics ........................................................................................................ 19
9.3
AC Characteristics ........................................................................................................ 20
TOP MARKING SPECIFICATIONS .......................................................................................... 21
10.1 W83L771AWG , W83L771AWG-2 and W83L771ASG-2 TOP MARKING ................... 21
10.2 W83L771ASG TOP MARKING..................................................................................... 21
Publication Release Date: 2009/10/21
Version: 1.9
-I-
11.
12.
PACKAGE SPECIFICATIONS .................................................................................................. 22
11.1 TSSOP (MSOP) 8L 3X3 MM2 ...................................................................................... 22
11.2 SOP8 150mil ................................................................................................................. 23
REVISION HISTORY ................................................................................................................ 24
Publication Release Date: 2009/10/21
Version: 1.9
- II -
W83L771AWG/W83L771ASG
1. GENERAL DESCRIPTION
The W83L771AWG/ASG, a one remote and one local temperature sensor with 2 temperature alert
TM
outputs and with 2-wire System Management Bus (SMBus ) serial interface, is Nuvoton hardware
monitoring IC specifically designed for PC, notebook and any embedded environments. The
W83771AWG/ASG uses Ideality Factor Configuration to eliminate temperature measurement error.
The remote temperature sensor input can be connected to thermal diode or transistor such as 2N3904.
A 10-bit plus sign ADC (Analog to Digital Converter) with 0.125C resolutions is built inside
W83L771AWG/ASG to convert the monitored temperature value. Programmable conversion rates and
stand-by mode support low-power operation.
TM
The W83L771AWG/ASG is a high temperature accuracy, low-power consumption, SMBus serial
interface IC, which is available in 8-pin, TSSOP (MSOP) and SOP package, with the working voltage of
3.3 V ±10%.
1.1
Product Selection Guide
PART NUMBER
SMBUS
ADDRESS
W83L771AWG
1001_100xb
W83L771AWG-2
1001_101xb
FUNCTIONALITY
REMOTE
1
W83L771ASG
1001_100xb
W83L771ASG-2
1001_101xb
LOCAL
1
OTHER
Programmable
temperature
High/Low limit
PACKAGE
TSSOP-8
(MSOP-8)
SOP-8
Publication Release Date: 2009/11/19
Version: 1.91
-1-
W83L771AWG/W83L771ASG
2. FEATURES
2.1
Monitoring Items - Temperature





2.2
General Features




ALERT Output supports SMBus

TM
2.0 protocol
Programmable Temperature High/Low limit and hysteresis for ALERT and T _ CRIT _ A
outputs
Package Type


2.4
TM
Interface: SMBus serial interface
3.3V± 10% VCC operation
10 bit plus sign remote temperature data format, 0.125C resolution
Programmable offset register for various thermal diodes
TM
SMBus 2.0 compatible interface, supports TIMEOUT
Programmable conversion rates allow user to optimize the power consumption.
Supply 2 alert outputs : ALERT and T _ CRIT _ A




2.3
Measure the temperature with high accuracy.
One on-chip thermal sensor
One remote temperature sensor input
Ideality Factor Configuration on External Diodes.
Remote Diode Fault Detection.
W83L771AWG in 8-pin TSSOP(MSOP)
W83L771ASG in 8-pin SOP
Applications




Desktop and Notebook Computers, support down to 45nm processes and below. (Please
refer to application notice for details)
Hardware Management
Servers
Embedded Applications
Publication Release Date: 2009/11/19
Version: 1.91
-2-
W83L771AWG/W83L771ASG
3. KEY SPECIFICATIONS

Local temperature range and accuracy
-40C to +125C (TA)
Typ.  2C (20C~40C)
Max.  3C (-40C~125C) *1

Remote temperature range and accuracy
-40C to +127C (TD)
Typ.  1C (25C ~70C)
Typ.  2C (-40C ~127C)
Max.  3C (-40C~127C) *2


Supply voltage
Operating supply current
Low Power Operation
ADC resolution include sign bit


3.3V ± 10%
900 uA typ.
15μA Standby Current
10 Bits
*1 Guaranteed by design from -40~125 degree C, 100% tested at 85 degree C.
*2 Guaranteed by design from -40~127 degree C, 100% tested at 85 degree C.
4. BLOCK DIAGRAM
xI
Control
Logic
Current
Generator
Command
Coder/DeCoder
SMBus
SCLK
REGISTER BANK
D1+
D1-
Analog Mux
Sensor
Circuitry
(Local/Remote)
Temperature
Registers
OVER
TEMPERATURE
COMPARATOR
Configuration
Registers
Status
Registers
Limit/Critical
(Hysteresis)
Registers
Fault Queue
ADC
Local Thermal
Sensor
SDA
ALERT
T_CRIT_A
Publication Release Date: 2009/11/19
Version: 1.91
-3-
W83L771AWG/W83L771ASG
5. PIN CONFIGURATION
8
1
VDD
2
D+
3
D-
7
W83L771AWG
W83L771ASG
SCL
SDA
6
4
5
T_CRIT_A
ALERT
GND
6. PIN DESCRIPTION
PIN TYPE
I/OD12ts
OD12
PIN ATTRIBUTE
TTL level and schmitt trigger open drain output with 12 mA sink capability
Open-drain output pin with 12 mA sink capability
INts
TTL level input pin and schmitt trigger
AIN
Input pin (Analog)
POWER
GROUND
Positive power supply input
Power supply ground
PIN NAME
NO
PIN TYPE
DESCRIPTION
VDD
1
POWER
D+
2
AIN
Connect to Thermal Diode Anode.
D-
3
AIN
Connect to Thermal Diode Cathode.
T _ CRIT _ A
4
OD12
T_CRIT alarm output, for interrupt or shutdown control.
GND
5
GROUND
ALERT
6
OD12
SDA
7
I/OD12ts
Digital I/O (Open drain). SMBus bidirectional serial data.
Requires a pull-up resistor.
SCL
8
INt s
Digital Input (Open drain). SMBus serial clock input.
Requires a pull-up resistor.
DC power supply, voltage input 3.3V 10%.
Power supply ground
Alarm output, for interrupt control.
Publication Release Date: 2009/11/19
Version: 1.91
-4-
W83L771AWG/W83L771ASG
7. FUNCTIONAL DESCRIPTION
7.1
General Description
The W83L771AWG/ASG provides one remote temperature sensor input which can be connected to the
2N3904 transistor, or CPU/GPU thermal diode, as well as one local on die thermal sensor to detect the
ambient temperature. The W83L771AWG/ASG supplies Ideality Factor Configuration on one External
Diode to eliminate the temperature measurement error. Selectable conversion rates and modes allow
low power operation.
The temperature measured by the W83L771AWG/ASG is digitally compared with the value stored in
the programmable High/Low limit Registers and T_CRIT registers. All out-of-limit values can be
detected by monitoring Status Register (SR). The W83L771AWG/ASG also supports SMBus
TM
2.0
ALERT mode and TIMEOUT.
The data format of the remote temperature is represented by a 10-bit plus sign, two‟s complement word
and 11-bit unsigned binary word with an LSB equal to 0.125C. The real temperature equals the
measured temperature plus or minus offset value. Offset value could be set in offset registers. The date
format of the offset registers is also the same as the data format of the remote temperature. Local
Temperature data is represented by an 8-bit plus sign, two‟s complement format, with an LSB equal to
1C.
Publication Release Date: 2009/11/19
Version: 1.91
-5-
W83L771AWG/W83L771ASG
7.2
Access Interface
The W83L771AWG/ASG provides SMBus serial interface to read/write internal registers, and the
SMBus address for read and write is 10011001b and 10011000b, respectively.
The W83L771AWG-2 and W83L771ASG-2 respond to hard-wire SMBus slave address as shown in
Table 1.1.
The first serial bus access timing is shown as follows:
7.2.1
Serial bus write to internal address register followed by the data byte
0
7
8
0
7
8
SCL
10
SDA
10
Start By
Master
0
1
00
1
10
R/W
D7
D6
AckAck
by
by
771AWG
78 5R
Frame 1
Serial Bus Address Byte
D5
D4
D3
D2
D1
D0
AckAck
by
by
771AWG
78 5R
Frame 2
Internal Index Register Byte
0
7
8
SCL (Continued)
SDA (Continued)
D7
D6
D5
D4
D3
D2
D1
D0
Ack
Ack
by
byby
771AWG
78
784R
5R
Frame 3
Data Byte
Stop
by
Master
Figure 1. Serial Bus Write to Internal Address Register followed by the Data By te
7.2.2
Serial bus read form internal address register followed by the data byte
0
SCL
SDA
10
Start By
Master
7
01
0
1
1
00
01
0
D7
R/W
7
D6
Ack by
771AWG
Frame 1
Serial Bus Address Byte
0
8
1
2
3
4
5
6
01
0
1
1
00
01
D5
D4
D3
D2
D1
D0
Ack
by
771AWG
Frame 2
Internal Index Register Byte
7
8
8
0
1
2
3
4
5
D7
D6
D5
D4
D3
D2
6
7
D1
D0
8
SCL(Continued)
SDA(Continued)
1
R/W
Ack
ack
by
by
771AWG
785R
Frame 3
Serial Bus Byte
by
Frame 4
Data Byte
784R
Ack
no
Ack
by
Master
Stop by
Master
Publication Release Date: 2009/11/19
Version: 1.91
-6-
W83L771AWG/W83L771ASG
7.3
ALERT
Output Mode
The W83L771AWG/ASG ALERT pin is an active-low open-drain output pin which is triggered when
the measured temperature exceeds the limitation defined in the limit registers. There are three types of
ALERT output mode: the ALERT output comparator mode, the ALERT output interrupt mode, and
the ALERT output SMBus ALERT mode.
7.3.1
ALERT
Output Comparator Mode
Fig. 7.3.1 shows the mechanism of the ALERT output comparator mode. Setting Filter and Alert
Configure Register, or register address BFh, D0 to 1 could enable the ALERT output comparator
mode. In this mode, the ALERT pin will be alerted if the monitored temperature is out-of-limit and the
ALERT pin keeps low until the temperature goes back to the target range. This mode is not power on
default setting.
High Limit
Measured Temperature By
W83L771AWG/ASG
W83L771AWG/ASG ALERT Pin
W83L771AWG/ASG High
Limit Status
Fig. 7.3.1 Response of
ALERT
output comparator mode
Publication Release Date: 2009/11/19
Version: 1.91
-7-
W83L771AWG/W83L771ASG
7.3.2
ALERT
Output Interrupt Mode
Fig. 7.3.2 shows the mechanism of the
ALERT output interrupt mode. In this mode, the
W83L771AWG/ASG will set the ALERT mask bit D7 of Configuration Register during a read of the
Status Register if any flag in Status Register, except the Busy flag D7 and OPEN flag D2, is set. This
prevents further ALERT triggering until the master has reset the ALERT mask bit, at the end of the
interrupt service routine. The Status Register flags are cleared only upon a read command from the
master and will be re-alerted at the end of the next temperature conversion if the measured
temperature still falls outside of the allowed range.
High Limit
Measured Temperature By
W83L771AWG/ASG
ALERT mask set in response to
reading of status register by
master
W83L771AWG/ASG ALERT Pin
End of Temperature conversion
W83L771AWG/ASG High
Limit Status
Fig. 7.3.2 Response of
ALERT
output interrupt mode
Publication Release Date: 2009/11/19
Version: 1.91
-8-
W83L771AWG/W83L771ASG
7.3.3
ALERT
Output SMBusTM ALERT Mode
Fig. 7.3.3 shows the mechanism of the ALERT output SMBus
TM
ALERT mode. In this mode, the
TM
ALERT output of the W83L771AWG/ASG is connected to the SMBus alert line which has more
than one device connected to it. Through such an implementation, SMBus
TM
ALERT mode can assist
the master in resolving which slave generates an interrupt. When the measured temperature falls
outside of the allowed range, the ALERT pin will be pulled low and the corresponding alert flags in
Status Register will be pulled high. The ALERT mask bit will just be set if there is a read command for
Status Register or when SMBus
TM
ALERT Response Address (ARA) occurs from master (Alert
Response Address is 0001100). Meanwhile, the W83L771AWG/ASG will generate and return its own
address to the master. If the temperature never falls outside of the allowed range, the latched ALERT
pin can release by the reset ALERT mask bit and the latched corresponding alert flags in Status
Register can release by reading command for Status Register. Please also refer to the
W83L771AWG_773G_775G Application Note 3.pdf for implementation.
High Limit
Measured Temperature By
W83L771AWG/ASG
ALERT mask set in response to
Alert Response Address from
master
W83L771AWG/ASG ALERT Pin
End of Temperature conversion
W83L771AWG/ASG High
Limit Status
Fig. 7.3.3 Response of
ALERT
output SMBus alert mode
Publication Release Date: 2009/11/19
Version: 1.91
-9-
W83L771AWG/W83L771ASG
7.4
T _ CRIT _ A
Output and T_CRIT flags
T _ CRIT _ A Output pulls low when the measured temperature exceeds the critical temperature
(T_CRIT) defined in 19h, and 20h for Remote, and Local T_CRIT set point, respectively. Once the
T _ CRIT _ A Output pulls low, it will not be set high until the measured temperature is lower than
(T_CRIT - TH), where TH is Temperature Hysteresis. Status Register will not be reset until it is read
and the temperature conversion falls below the T_CRIT set point. The ALERT will also be asserted for
T_CRIT event, Figure 7.4 shows this mechanism. Please also refer to the W83L771AWG_773G_775G
Application Note 4.x.pdf for implementation.
T_CRIT# Set point
TH Value
T_CRIT - TH
Measured temperature by W83L771
W83L771 T_CRIT# pin
W83L771 T_CRIT status
W83L771 read command for
status register
W83L771 ALERT# pin
W83L771 status register read
ALERT Mask will be set
Fig. 7.4 Response of T _ CRIT _ A output
Publication Release Date: 2009/11/19
Version: 1.91
- 10 -
W83L771AWG/W83L771ASG
7.5
Measured Temperature Data Format
The W83L771AWG/ASG can measure remote temperature with the resolution of 11-bit two‟s
complement format and local temperature with the resolution of 8-bit two‟s complement format.
7.5.1
Measure Remote Temperature Data Format
Table 7.5.1 shows the remote temperature data with 11-bit two‟s complement format.
Table 7.5.1 Measured Remote Temperature Data Format
TEMPERATURE
8-BIT DIGITAL OUTPUT HIGH
BYTE
8-BIT DIGITAL OUTPUT LOW
BYTE
+127.875°C
0111,1111
111X,XXXX
+25.750°C
0001,1001
110X,XXXX
+2.250°C
0000,0010
010X,XXXX
+1.125°C
0000,0001
001X,XXXX
+0.000°C
0000,0000
000X,XXXX
- 1.125°C
1111,1110
111X,XXXX
- 2.250°C
1111,1101
110X,XXXX
- 25.750°C
1110,0110
010X,XXXX
- 127.875°C
1000,0000
001X,XXXX
7.5.2
Measure Local Temperature Data Format
Table 7.5.2 shows the local temperature data with 8-bit two‟s complement format.
Table 7.5.2 Measured Local Temperature Data Format
TEMPERATURE
8-BIT DIGITAL OUTPUT
+127°C
0111,1111
+25°C
0001,1001
+2°C
0000,0010
+1°C
0000,0001
+0°C
0000,0000
- 1°C
1111,1111
- 2°C
1111,1110
- 25°C
1110,0111
- 128°C
1000,0000
Publication Release Date: 2009/11/19
Version: 1.91
- 11 -
W83L771AWG/W83L771ASG
7.6
Digital Filter
The W83L771AWG/ASG provides three Digital Filter levels to suppress erroneous remote temperature
readings due to noise. The register address to set the digital filter is at Filter and Alert Configure
Register. If set bits <D2, D1> = <0, 0>, then no filter is selected. If set bits <D2, D1> = <0, 1> or <1, 0>,
then filter level 1 is selected. If set bits <D2, D1> = <1, 1>, then level 2 is selected. Figure 7.6.1 shows
the step response of reading remote temperature with different filter level, and Figure 7.6.2 shows the
impulse response.
Temperature (oC)
5
0
4
5
4
0
No Filter Level
3
5
Filter Level 1
Filter Level 2
3
0
2
5 0
5
1
1
2
0
5
0
SAMPLE NUMBER
2
5
Figure 7.6.1 Step Response of reading remote temperature
Temperature (oC)
5
0
4
5
4
0
No Filter Level
3
5
Filter Level 1
Filter Level 2
3
0
2
5 0
5
1
1
2
0
5
0
SAMPLE NUMBER
2
5
Figure 7.6.2 Impulse Response of reading remote temperature
Publication Release Date: 2009/11/19
Version: 1.91
- 12 -
W83L771AWG/W83L771ASG
7.7
Fault Detect
Table 7.7 shows the response of Fault Detection if the false connection of D+ and D- occurs after the
power-up. Please also refer to the W83L771AWG_773G_775G Application Note 2.pdf for
implementation.
Table 7.7 response of Fault Detect
7.8
CONNECTION (D+, D-)
STATUS REGISTER BIT
MEASURED REMOTE
TEMPERATURE
(VDD, Floating)
1
+127.875 ℃
(GND, Floating)
1
+127.875 ℃
(Floating, Floating)
1
+127.875 ℃
Short
1
+127.875 ℃
Conversion Rate and Moving Average
The W83L771AWG/ASG provides an embedded moving average into conversion rate selection. Each
conversion rate can set a couple of proper noise rejection and average supply current.
Publication Release Date: 2009/11/19
Version: 1.91
- 13 -
W83L771AWG/W83L771ASG
8. CONTROL AND STATUS REGISTER
8.1
W83L771AWG/ASG Registers
READ
ADDRESS
(HEX)
WRITE
ADDRESS
(HEX)
Local Temperature (LT)
00h
Remote Temperature High Byte
(RTHB)
REGISTER NAME
(HEX)
POWER ON DEFAULT STATES
<D7:D0>
BINARY / HEX
DECIMAL
Read Only
0000,0000b / 00h
0
01h
Read Only
0000,0000b / 00h
0
Status Register 1 (SR)
02h
Read Only
0000,0000b / 00h
0
Configuration
03h
09h
0000,0001b / 01h
1
Conversion Rate (CR)
04h
0Ah
0000,1000b / 08h
8
Local High Set point (LHS)
05h
0Bh
0100,0110b / 46h
70
Local Low Set point (LLS)
06h
0Ch
1101,1011b / DBh
-40
Remote High Set point High Byte
(RHSHB)
07h
0Dh
0100,0110b / 46h
70
Remote Low Set point High Byte
(RLSHB)
08h
0Eh
1101,1011b / DBh
-40
Remote Temperature Low Byte
(RTLB)
10h
Read Only
0000,0000b / 00h
0
Remote Temperature Offset High
Byte (RTOHB)
11h
11h
0000,0000b / 00h
0
Remote Temperature Offset Low
Byte (RTOLB)
12h
12h
0000,0000b / 00h
0
Remote High Set point Low Byte
(RHSLB)
13h
13h
0000,0000b / 00h
0
Remote Low Set point Low Byte
(RLSLB)
14h
14h
0000,0000b / 00h
0
Remote T_CRIT Set point (RCS)
19h
19h
0110,1110b / 6Eh
110
Local T_CRIT Set point (LCS)
20h
20h
0101,0101b / 55h
85
T_CRIT Set point (TH)
21h
21h
0000,1010b / 0Ah
10
Remote Diode Temperature Filter
(RDTF)
BFh
BFh
0000,0000b / 00h
0
Remote Diode ideality (IDEA)
E3h
E3h
1000,0100b / 84h
132
Read Manufacturer‟s ID (RMID)
FEh
Read Only
0101,1100b / 5Ch
92
Read Die Revision (RDR)
FFh
Read Only
0001,0000b / 10h
0001,0001b / 11h
0001,0011b / 13h
16
17
19
(C)
Publication Release Date: 2009/11/19
Version: 1.91
- 14 -
W83L771AWG/W83L771ASG
8.2
Data Format of Temperature Registers (LT, RTHB, RTLB, LHS, RHSHB,
RHSLB, LLS, RLSHB, RLSLB, RTOHB, RTOLB, RCS, LCS)
The following table shows the data format, Two‟s Complement, of the temperature, including Local
Temperature (LT), Remote Temperature High Byte (RTHB), Local High Set point (LHS), Remote High
Set point High Byte (RHSHB), Local Low Set point (LLS), Remote Low Set point High Byte (RLSHB),
Remote Temperature Offset High Byte (RTOHB), Remote T_CRIT Set point (RCS), Local T_CRIT Set
point (LCS), Remote Temperature Low Byte (RTLB), Remote High Set point Low Byte (RHSLB),
Remote Low Set point Low Byte (RLSLB), and Remote Temperature Offset Low Byte (RTOLB). Only
remote temperature, remote high set point, remote low set point, and remote temperature offset
support two bytes, up to 0.125℃ resolution, for the temperature data format; others support one byte,
up to 1℃ resolution, for the temperature data format.
REGISTER OF HIGH BYTE: LT, RTHB, LHS, RHSHB, LLS, RLSHB, RTOHB, RCS, LCS
DATA FORMAT: TWO’S COMPLEMENT FORMAT
BIT
D7
D6
D5
D4
D3
D2
D1
D0
VALUE
Sign
64
32
16
8
4
2
1
Unit: ℃
REGISTER OF LOW BYTE: RTLB, RHSLB, RLSLB, RTOLB
DATA FORMAT: TWO’S COMPLEMENT FORMAT
BIT
D7
D6
D5
D4
D3
D2
D1
D0
VALUE
0.5
0.25
0.125
0
0
0
0
0
The following table shows some examples.
REGISTER OF HIGH BYTE
REGISTER OF LOW BYTE (IF ANY)
TEMPERATURE
D7
D6
D5
D4
D3
D2
D1
D0
D7
D6
D5
D4
D3
D2
D1
D0
+127.875℃
0
1
1
1
1
1
1
1
1
1
1
X
X
X
X
X
0.125℃
0
0
0
0
0
0
0
0
0
0
1
X
X
X
X
X
0℃
0
0
0
0
0
0
0
0
0
0
0
X
X
X
X
X
-1.125℃
1
1
1
1
1
1
1
0
1
1
1
X
X
X
X
X
-25.75℃
1
1
1
0
0
1
1
0
0
1
0
X
X
X
X
X
-127.875℃
1
0
0
0
0
0
0
0
0
0
1
X
X
X
X
X
To obtain the two-byte temperature data correctly, it is required to read High Byte data, followed by
reading Low Byte data.
Publication Release Date: 2009/11/19
Version: 1.91
- 15 -
W83L771AWG/W83L771ASG
8.3
Status Register (SR)
Read Address: 02h
Write Address: Read Only
Power On Default States: 00h
BIT FLAG NAME
DESCRIPTION
D7
Busy
Setting to „1‟ indicates ADC is busy converting.
D6
LHIGH
Setting to „1‟ indicates a measured Local Temperature Higher than Local High set
point (High Limit).
D5
LLOW
Setting to „1‟ indicates a measured Local Temperature lower than Local Low set
point (Low Limit).
D4
RHIGH
Setting to „1‟ indicates a measured Remote Temperature higher than Remote
High set point (High Limit).
D3
RLOW
Setting to „1‟ indicates a measured Remote Temperature lower than Remote Low
set point (Low Limit).
D2
OPEN
Setting to „0‟ indicates that D+ and D- pins are connected with a Remote Diode.
Setting to „1‟ indicates that D+ and D- pins are disconnected with a Remote
Diode, or float, or short.
D1
RCRIT
Setting to „1‟ indicates a Remote Critical Temperature alarm.
D0
LCRIT
Setting to „1‟ indicates a Local Critical Temperature alarm.
8.4
Configuration Register (C)
Read Address: 03h
Write Address: 09h
Power On Default States: 01h
BIT
FLAG NAME
DESCRIPTION
D7
ALERT mask
If this bit is set to „1‟ ALERT interrupts are masked.
D6
STOP/ RUN
If this bit is set to „1‟, Device into standby mode.
D5
0
No definition and this bit can be read as 0.
D4
Remote T _ CRIT _ A mask If this bit is set to „1‟ Remote T _ CRIT _ A interrupts are masked.
D3
0
No definition and this bit can be read as 0.
D2
Local T _ CRIT _ A mask
If this bit is set to „1‟ Local T _ CRIT _ A interrupts are masked.
D1
0
No definition and this bit can be read as 0.
D0
Reserved
Reserved
Publication Release Date: 2009/11/19
Version: 1.91
- 16 -
W83L771AWG/W83L771ASG
8.5
T_CRIT Hysteresis Register (TH)
Read Address: 21h
Write Address: 21h
Power On Default States: 0Ah
REGISTER: TH
(MAX. VALUE: 31)
BIT
D7
D6
D5
D4
D3
D2
D1
D0
VALUE
0
0
0
16
8
4
2
1
Unit: ℃
8.6
Conversion Rate Register (CR)
Read Address: 04h
Write Address: 0Ah
Power On Default States: 08h
REGISTER: CR
(DEFAULT CONVERSION RATE: 16HZ)
(OPENA, OPENB)
0
1
Temp. sensor
1 local + 1remote(A or B)
1 local
BIT<D7:D0>
Frequency/Time(Sec)
Average IVDD
00h
0.0625Hz/16
==
0.0625Hz/16
==
01h
0.125Hz/8
==
0.125Hz/8
==
02h
0.25Hz/4
==
0.25Hz/4
==
03h
0.5Hz/2
211uA
0.5Hz/2
211uA
04h
1Hz/1
232uA
1Hz/1
232uA
05h
2Hz/0.5
331uA
2Hz/0.5
331uA
06h
4Hz/0.25
393uA
4Hz/0.25
393uA
07h
8Hz/0.125
589uA
8Hz/0.125
589uA
08h
16Hz/0.0625
833uA
16Hz/0.0625
833uA
09h-FFh
Reserved
Frequency/Time(Sec) Average IVDD
Reserved
Publication Release Date: 2009/11/19
Version: 1.91
- 17 -
W83L771AWG/W83L771ASG
8.7
Filter and Alert Configure Register (RDTF)
Read Address: BFh
Write Address: BFh
Power On Default States: 00h
BIT
DESCRIPTION
<D7:D3>
0
No definition and this bit can be read as 0.
<D2:D1>
RDTFA
Filter Level
<D2, D1>=<0, 0>: No Filter Selected
<D2, D1>=<0, 1> or <1, 0>: Filter Level 1 Selected
<D2, D1>=<1, 1>: Filter Level 2 Selected
ALERT Configure
If this bit is set to „1‟ ALERT Output Comparator mode is
enabled.
D0
8.8
COMMAND
Ideality (IDEA)
The Ideality Factor is dependant upon the process that was used in the fabrication of the particular
diode.
Read Address: E3h
Write Address: E3h
Power On Default States: 84h
REGISTER: IDEA (DEFAULT IDEALITY: 1.003)
BIT<D7:D0>
RANGE
86h
0.9851~0.9924
85h
0.9925~1.0000
84h
1.0001~1.0076
83h
1.0077~1.0153
82h
1.0154~1.0232
81h
1.0233~1.0312
80h
1.0313~1.0393
7Fh
1.0394~1.0476
7Eh
1.0477~1.0560
7Dh
1.0561~1.0645
7Ch
1.0646~1.0731
7Bh
1.0732~1.0819
00h-7Ah, 87h-FFh
Reserved
Publication Release Date: 2009/11/19
Version: 1.91
- 18 -
W83L771AWG/W83L771ASG
9. ELECTRICAL CHARACTERISTIC
9.1
Absolute Maximum Ratings
PARAMETER
RATING
UNIT
Power Supply Voltage
3.3V  10%
V
Input Voltage
-0.3
to
+3.6
V
Operating Temperature*
-40
to
+125
C
Storage Temperature
-50
to
+150
C
*Guaranteed by design, 100% test at 85 degreeC.
Note: Exposure to conditions beyond those listed under Absolute Maximum Ratings may adversely affect the life and reliability of
the device.
9.2
DC Characteristics
(Ta = 0 C to 85 C, VDD = 3.3V  10%, VSS = 0V)
PARAMETER
SYM.
MIN.
TYP.
MAX.
UNIT
CONDITIONS
I/O12ts - TTL level bi-directional pin with source-sink capability of 12 mA and schmitt-trigger
level input
Input Low Threshold Voltage
Vt-
0.5
0.8
Input High Threshold Voltage
Vt+
1.6
2.0
Hysteresis
VTH
0.5
1.2
Output Low Voltage
VOL
Output High Voltage
VOH
Input High Leakage
ILIH
Input Low Leakage
ILIL
1.1
V
VDD = 3.3 V
V
VDD = 3.3 V
V
VDD = 3.3 V
V
IOL = 12 mA
V
IOH = - 12 mA
+10
A
VIN = VDD
-10
A
VIN = 0V
0.4
V
IOL = 12 mA
2.4
0.4
2.4
OD12 - Open-drain output pin with sink capability of 12 mA
Output Low Voltage
INts -
VOL
TTL level Schmitt-triggered input pin
Input Low Threshold Voltage
Vt-
0.5
0.8
1.1
V
VDD = 3.3 V
Input High Threshold Voltage
Vt+
1.6
2.0
2.4
V
VDD = 3.3 V
Hysteresis
VTH
0.5
1.2
V
VDD = 3.3 V
Input High Leakage
ILIH
+10
A
VIN = VDD
Input Low Leakage
ILIL
-10
A
VIN = 0 V
Publication Release Date: 2009/11/19
Version: 1.91
- 19 -
W83L771AWG/W83L771ASG
9.3
AC Characteristics
t
t
SCL
t
R
R
SCL
t
t SU;DAT
t HD;SDA
SU;STO
VALID DATA
SDA IN
t
HD;DAT
SDA OUT
Serial Bus Timing Diagram
Timing for W83L771AWG/ASG :
PARAMETER
SYMBOL
SCL clock period
t SCL
2.5
uS
Start condition hold time
tHD;SDA
1.5
uS
Stop condition setup-up time
tSU;STO
1
uS
DATA to SCL setup time
tSU;DAT
120
nS
DATA to SCL hold time
tHD;DAT
5
nS
SCL and SDA rise time
tR
1.0
uS
SCL and SDA fall time
tF
300
nS
-
MIN.
MAX.
UNIT
Publication Release Date: 2009/11/19
Version: 1.91
- 20 -
W83L771AWG/W83L771ASG
10. TOP MARKING SPECIFICATIONS
10.1 W83L771AWG , W83L771AWG-2 and W83L771ASG-2 TOP MARKING
771AW
G-2 G
715D
771AW
G GBA
715B
FIRST+SECOND LINE
771AS
G-2 G
715D
IC part number: 771AWG (W83L771AWG), 771AWG-2 (W83L771AWG-2),
771ASG-2 (W83L771ASG-2)
Tracking Code 1
SECOND LINE
G
Assembly house code
BA
Mask version (eliminated from the top marking of W83L771AWG-2
and W83L771ASG-2)
Tracking Code 2
THIRD LINE
7
The package is made in 2007
15
Week: 15
B
IC version
10.2 W83L771ASG TOP MARKING
W83L7
71ASG
715GB
FIRST+SECOND LINE IC part number: W83L771ASG
Tracking Code 2
THIRD LINE
7
The package is made in 2007
15
Week: 15
G
Assembly house code
B
IC version
Publication Release Date: 2009/11/19
Version: 1.91
- 21 -
W83L771AWG/W83L771ASG
11. PACKAGE SPECIFICATIONS
11.1 TSSOP (MSOP) 8L 3X3 MM2
Publication Release Date: 2009/11/19
Version: 1.91
- 22 -
W83L771AWG/W83L771ASG
11.2 SOP8 150mil
8
5
E
4
1
Control demensions are in milmeters .
E

Publication Release Date: 2009/11/19
Version: 1.91
- 23 -
W83L771AWG/W83L771ASG
12. REVISION HISTORY
VERSION
1.0
DATE
01/28/2008
PAGE
DESCRIPTION
20
The versions before 1.0 are preliminary
version
Remove section 8.9 Configuration on Beta
Compensation Technology.
1. Modify Chapter 4 Block Diagram.
2. Add the descriptions of “POWER” and
“GROUND” to Chapter 6 Pin Descriptions.
3. Correct the description and update
“ALERT protocol” to “ALERT mode” in
section 7.1 General Description.
4. Update the descriptions in 7.3.2
ALERT Output Interrupt Mode.
5. Update Figure 7.3.1, Figure 7.3.2, Figure
7.3.3, Figure 7.4, and Figure 7.6.1.
6. Update “RDTF1” to “RDTF”, remove
“Remote Diode Ideality Low Byte”, and
correct the default of “Remote Diode
Ideality” in section 8.1
W83L771AWG/ASG Registers.
7. Update the information in section 9.1
Absolute Maximum Ratings.
8. Modify the description of bit D2 of 8.3
Status Register.
1.1
03/04/2008
3, 5, 6, 8, 9, 10,
15, 17, 20
1.2
03/25/2008
17-19
1.3
01/15/2009
1,15,19,22
1.4
02/03/2009
3
1. Modified the remote temperature
accuracy range.
1.5
03/06/2009
3
1. Added maximum accuracy range
definition.
1.6
04/15/2009
3,19
1.7
06/18/2009
2
1.8
10/7/2009
9,10,13
1.9
10/21/2009
20
1.91
11/19/2009
21
1. Add the power-on default states, read
address, and write address of registers
1. Modified the typo of Ideality CR[E3h]
default value.
2. Added W83L771AWG-2/ASG-2 info.
1.
Modified the operation temperature range
definition.
Added processor type support description.
1.
2.
Added APN reference description.
Added application notice for T_CRIT#.
1.
Modified the AC characteristic to support
400KHz serial bus.
1.
Correct the top marking
Publication Release Date: 2009/11/19
Version: 1.91
- 24 -
W83L771AWG/W83L771ASG
Important Notice
Nuvoton Products are neither intended nor warranted for usage in systems or equipment, any
malfunction or failure of which may cause loss of human life, bodily injury or severe property
damage. Such applications are deemed, “Insecure Usage”.
Insecure usage includes, but is not limited to: equipment for surgical implementation, atomic
energy control instruments, airplane or spaceship instruments, the control or operation of
dynamic, brake or safety systems designed for vehicular use, traffic signal instruments, all
types of safety devices, and other applications intended to support or sustain life.
All Insecure Usage shall be made at customer’s risk, and in the event that third parties lay
claims to Nuvoton as a result of customer’s Insecure Usage, customer shall indemnify the
damages and liabilities thus incurred by Nuvoton.
Publication Release Date: 2009/11/19
Version: 1.91
- 25 -