PG300R THRU PG308R 50V-800V 3.0A GLASS PASSIVATED JUNCTION FAST SWITCHING RECTIFIER FEATURES l Plastic package has Underwriters Laboratory Flammability Classification 94V-O Utilizing l l Flame Retardant Epoxy Molding Compound Glass passivated junction in a DO-201AD package 3 ampere operation at TA=55 °C with no thermal runaway l Exceeds environmental standards of MIL-S-19500/228 l Fast switching for high efficiency MECHANICAL DATA Case: Molded plastic, DO-201AD Terminals: axial leads, solderable per MIL-STD-202, Method 208 Mounting Position: Any Weight: 0.04 ounce, 1.1 grams MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. PG300R PG301R PG302R PG304R PG306R PG308R UNITS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current .375”, 9.5mm Lead Length at TA=55 ¢J Peak Forward Surge Current 8.3ms single half sine wave superimposed on rated load(JECEC method) Maximum Forward Voltage at 3.0A Maximum Reverse Current at Rated DC Ta=25 ¢J Blocking Voltage Ta=100 ¢J Typical Junction capacitance (Note 1) CJ Typical Thermal Resistance (Note 2) R £KJA Maximum Reverse Recovery Time(Note 3) Operating and Storage Temperature Range TA 50 35 50 150 100 70 100 150 200 140 200 400 280 400 600 420 600 800 560 800 3.0 V V V A 125 A 1.3 5.0 300 V 60 22.0 PF A °C /W 150 150 -55 to +150 250 500 ns °C NOTES: 1. Measured at 1 MHz and applied reverse voltage of 4.0 VDC 2. Thermal resistance from junction to ambient at 0.375"(9.5mm) lead length P.C.B. mounted 3. Reverse Recovery Test Conditions: IF=.5A, IR=1A, Irr=.25A E-mail: [email protected] 1 of 2 Web Site: www.taychipst.com PG300R THRU PG308R 50V-800V 3.0A GLASS PASSIVATED JUNCTION FAST SWITCHING RECTIFIER RATINGS AND CHARACTERISTIC CURVES PG300R THRU PG308R trr +0.5A 0 -0.25 -1.0 NOTE:1.Rise Time = 7ns max. Input Impedance = 1 megohm. 22pF 2.Rise Time = 10ns max. SET TIME BASE FOR 50 ns/cm Source Impedance = 50 Ohms 1cm 4.0 3.0 .375" 9.5mm LENGTH 2.0 1.0 0 25 50 75 100 125 150 175 125 PEAK FORWARD SURGE CURRENT, AMPERES NON REPETITIVE 100 50 TJ = 25¢J 25 REPETITIVE 10 1 200 10 50 100 AMBIENT TEMPERATURE, ¢J NUMBER OF CYCLES AT 60Hz Fig. 2-FORWARD CURRENT CURVE Fig. 3-PEAK FORWARD SURGE CURRENT INSTANTANEOUS FORWARD CURRENT, AMPERES AVERAGE FORWARD CURRENT (10)-AMP (10)-AAV Fig. 1-REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 100 TJ =25 ¢J CAPACITANCE, pF 60 10 5 1 1 4 10 50 100 30 10 3.0 TJ = 25 ¢J 1.0 0.3 0.1 0.03 0.01 0.6 REVERSE VOLTAGE, VOLTS 0.7 0.8 1.0 1.1 1.2 1.3 INSTANTANEOUS FWD VOLTAGE, VOLTS Fig. 4-TYPICAL JUNCTION CAPACITANCE E-mail: [email protected] 100 Fig. 5-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTIC 2 of 2 Web Site: www.taychipst.com