PS300R THRU PS3010R FAST SWITCHING PLASTIC RECTIFIER VOLTAGE - 50 to 1000 Volts CURRENT - 3.0 Amperes FEATURES l High surge current capability l Plastic package has Underwriters Laboratory Flammability Classification 94V-O utilizing l l Flame Retardant Epoxy Molding Compound Void-free Plastic in DO-201AD package 3 ampere operation at TA=55 ¢J with no thermal runaway l Exceeds environmental standards of MIL-S-19500/228 l Fast switching for high efficiency DO-201AD MECHANICAL DATA Case: Molded plastic , DO-201AD Terminals: Axial leads, solderable per MIL-STD-202, Method 208 Polarity: Band denotes cathode Mounting Position: Any Weight: 0.04 ounce, 1.1 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 ¢J ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. PS300R PS301R PS302R PS304R PS306R PS308R PS3010R UNITS Maximum Recurrent Peak Reverse Voltage 50 100 200 400 600 800 1000 V Maximum RMS Voltage 35 70 140 280 420 560 700 V Maximum DC Blocking Voltage 50 100 200 400 600 800 1000 V Maximum Average Forward Rectified 3.0 A Current .375"(9.5mm) Lead Length at TA=55 ¢J Peak Forward Surge Current 8.3ms single 200 A half sine-wave superimposed on rated load (JEDEC method) Maximum Forward Voltage at 3.0A 1.3 V 5.0 £g A Maximum Reverse Current TJ=25 ¢J 500 at Rated DC Blocking Voltage TJ=100 ¢J £g A Maximum Reverse Recovery Time(Note 1) 150 150 150 150 250 500 500 ns Typical Junction capacitance (Note 2) CJ 60 PF Typical Thermal Resistance (Note 3) R £KJA 22 ¢J /W Operating and Storage Temperature Range -55 TO +150 ¢J NOTES: 1. Reverse Recovery Test Conditions: IF=.5A, IR=1A, Irr=.25A 2. 3. Measured at 1 MHz and applied reverse voltage of 4.0 VDC Thermal Resistance from Junction to Ambient and from junction to lead at 0.375"(9.5mm) lead length with both leads equally heatsink. RATING AND CHARACTERISTIC CURVES PS300R THRU PS3010R trr +0.5A 0 -0.25 -1.0 NOTE:1.Rise Time = 7ns max. Input Impedance = 1 megohm. 22pF 2.Rise Time = 10ns max. 1cm SET TIME BASE FOR 50 ns/cm Source Impedance = 50 Ohms 4.0 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD CURRENT (10)-AMP (10)-AAV Fig. 1-REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 3.0 .375" 9.5mm LENGTH 2.0 1.0 0 25 50 75 100 125 150 175 200 NON REPETITIVE 100 50 TJ = 25¢J REPETITIVE 10 200 1 AMBIENT TEMPERATURE, ¢J 100 T J = 25 ¢J CAPACITANCE, pF 60 10 5 1 1 4 10 50 100 REVERSE VOLTAGE, VOLTS Fig. 4-TYPICAL JUNCTION CAPACITANCE 50 100 NUMBER OF CYCLES AT 60Hz Fig. 3-PEAK FORWARD SURGE CURRENT INSTANTANEOUS FORWARD CURRENT, AMPERES Fig. 2-FORWARD CURRENT DERATING CURVE 10 100 30 10 3.0 TJ = 25 ¢J 1.0 0.3 0.1 0.03 0.01 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 INSTANTANEOUS FWD VOLTAGE, VOLTS Fig. 5-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS