TRIQUINT TQM7M9023

TQM7M9023
Data Sheet
5.0x7.5mm Multimode Multiband Power Amplifier (MMPA)
(Quad-Band GSM / EDGE and Tri-band W/CDMA/HSPA+/LTE)
Functional Block Diagram
Features












Quad-Band Linear GSM/EDGE
UMTS B1 and B5/8
Input power controlled – GMSK and 8PSK
GSM LB has 3 modes – HP, MP, LP
GSM HB has 2 modes – HP, LP
W/CDMA has 3 modes – HP, MP, LP
HBT/PHEMT / CuFlip® PA Technology
Integrated coupler
Built-in voltage regulator
50Ω input and Output Impedance
Lead-free 260°C / RoHS / Halogen-free
24 Pin 5x7.5mm Package
Applications
Product Description
The TQM7M9023 is a fully matched multimode multiband Power Amplifier Module
that supports Quad-band GSM/EDGE Linear, W/CDMA & LTE Band 1, and low
band WCDMA/LTE (externally tuned for either Band 5 or Band 8). The GSM PA
output power is controlled by the input power coming from the transceiver in both
GMSK and 8PSK modes. The 3-Gain state WCDMA PA operates in LPM, MPM and
HPM to maximize talk time over the entire range of operating conditions. It also
includes a coupler and built-in regulator, ideal for today’s extremely small data
enabled phones. The TQM7M9023 is designed on TriQuint’s GaAs HBT technology
with CuFlip® assembly offering state of the art reliability, temperature stability and
ruggedness. Its RF performance meets the stringent linearity requirements for
multi-mode operation.





GSM/EDGE/WEDGE Applications
WCDMA B1/8 or B1/5 Applications
WCDMA B1/5/8 Applications (w/ external
switch)
HSDPA/HSUPA/HSPA+ Applications
LTE Applications / EVDO revA B1&B5
Package Style
Electrical Specifications
Parameter
HPM Pout
HPM PAE
LPM ICC @
3.5dBm Pout
HPM ICC@Psat
Data Sheet
GSM850/900 DCS/PCS UMTS B1 UMTS B5 UMTS B8 Units
Typ
Typ
Typ
Typ
Typ
35
55
33
50
28
40
8
28.25
40
8
28.25
40
8
dBm
%
mA
1.5
1
0.46
0.46
0.46
A
For additional information and the latest specifications, see our website: www.triquint.com
Revision F,September, 2011
24-Pin Laminate Module
Top View
1
TQM7M9023
Data Sheet
5.0x7.5mm Multimode Multiband Power Amplifier (MMPA)
(Quad-Band GSM / EDGE and Tri-band W/CDMA/HSPA+/LTE)
Absolute Maximum Ratings
Parameter
Positive Supply voltage
Control Voltages (enable, VMODE0, VMODE1
Input RF Power
Storage Temperature
Operating Case (ambient) Temperature
HBM ESD
Peak Reflow Temperature
Ruggedness (Pout ≤ max power, all phases)
Duty Cycle at Maximum Power
Moisture Sensitivity Level
Symbol
VBATT, VCC
LB_EN, HB_EN, VMODE0, VMODE1
PIN
Tstorage
Tcase
ESD
Tmax
Rating
-0.5 to +5.5
-0.5 to +5.5
+15
-30 to +150
-20 to +90
Class 1C
260
10:1
50
MSL3
Ruggedness
Units
V
V
dBm
°C
°C
°C
VSWR
%
δ
MSL
Note 1: Stresses greater than the listed absolute maximum ratings may cause permanent and functional damage to the device.
Note 2: Exposure exceeding absolute maximum rating conditions for extended periods may affect device reliability
Note 3: ESD HBM meets conditions defined in JESD22-A114-E.
Note 4: Part may not survive all maximums applied simultaneously
Operating Parameters
DC Supply
Supply voltage (VBATT, VCC)
VMODE0, VMODE1 (digital control)
LB_EN, HB_EN
Rise Time
Fall Time
Operating Case Temperature
Condition
GMSK Operation
8PSK Operation
WCDMA Operation
WCDMA Operation with DCDC
Low
High
Current
From Pout = -30 dBm to Pout = Pmax
From Pout = -30 dBm to Pout = Pmax
Min
3.0
3.2
3.2
1.0
0
1.35
-20
Typ
3.5
3.5
3.4
1.8
Max
4.5
4.2
4.2
4.0
0.5
3.1
0.1
1
1
+85
Unit
V
V
V
V
V
V
mA
µS
µS
°C
UMTS Turn on/off time
DC: Icc to within 90% of final value
RF: Pout within 1dB of final value
20
6
µs
µs
Mode switching time
With PA_ON = high
2
µs
Data Sheet
For additional information and the latest specifications, see our website: www.triquint.com
Revision F,September, 2011
2
TQM7M9023
Data Sheet
5.0x7.5mm Multimode Multiband Power Amplifier (MMPA)
(Quad-Band GSM / EDGE and Tri-band W/CDMA/HSPA+/LTE)
Modes of Operation
Mode of Operation
LB_EN
HB_EN
Mode
Powerdown
Low
Low
X1
GSM 850/900 – High-power mode
High
Low
Low
GSM 850/900 – Medium-Power mode
High
Low
Low
GSM 850/900 – Low-power mode
High
Low
Low
DCS/PCS – High-power mode
Low
High
Low
DCS/PCS – Low-power mode
Low
High
Low
UMTS Band 5/8 – High-power mode
High
Low
High
UMTS Band 5/8– Medium Power mode
High
Low
High
UMTS Band 5/8– Low-Power mode
High
Low
High
UMTS Band 5/8– Optional Lower Vcc
High
Low
High
UMTS Band 1 – High-power mode
Low
High
High
UMTS Band 1 – Medium Power mode
Low
High
High
UMTS Band 1 – Low-Power mode
Low
High
High
UMTS Band 1 – Optional Lower Vcc
Low
High
High
Note 1: Logic input currents will be minimized when Mode, Vmode0 and Vmode1 are low.
Recommended GSM Power Levels for each Mode of Operation
GMSK Modes
Low band – High-power mode
Low band – Medium power mode
Low band – Low-power mode
High band – High-power mode
High band – Low-power mode
PCL
5-6
7-13
14-19
0-7
8-15
VMODE0
X1
Low
Low
High
Low
High
Low
High
High
High
Low
High
High
High
VMODE1
X1
Low
High
Low
Low
Low
X
Low
High
High
X
Low
High
High
VBATT
On
On
On
On
On
On
On
On
On
On
On
On
On
On
VCC
On
On
On
On
On
On
On
On
On
1.5V
On
On
On
1.5V
Output Power Range
30.5 dBm < POUT ≤ Psat
16 dBm < POUT ≤ 30.5 dBm
POUT ≤ 16 dBm
16 dBm < POUT ≤ Psat
POUT ≤ 16 dBm
Recommended EDGE Power Levels for each Mode of Operation
8PSK Modes
Low band – High power mode
Low band – Medium power mode
Low band – Low-power mode
High band – High-power mode
High band – Low-power mode
PCL
8-9
10-15
16-19
0-10
11-15
Output Power Range
23 dBm < POUT ≤ 29dBm
14 dBm ≤ POUT ≤ 23dBm
POUT ≤ 12 dBm
10 dBm < POUT ≤ 28dBm
POUT ≤ 10 dBm
Recommended WCDMA Power Levels for each Mode of Operation
8PSK Modes
Band 5/8 – High power mode
Band 5/8 – Medium power mode
Band 5/8 – Low-power mode / Optional Lower Vcc
Band 1 – High-power mode
Band 1 – Medium power mode
Band 1 – Low-power mode / Optional Lower Vcc
Data Sheet
Output Power Range
17 dBm < POUT ≤ 28.25 dBm
9 dBm ≤ POUT ≤ 17 dBm
POUT < 9 dBm
17 dBm < POUT ≤ 28 dBm
8 dBm ≤ POUT ≤ 17 dBm
POUT ≤ 8 dBm
For additional information and the latest specifications, see our website: www.triquint.com
Revision F,September, 2011
3
TQM7M9023
Data Sheet
5.0x7.5mm Multimode Multiband Power Amplifier (MMPA)
(Quad-Band GSM / EDGE and Tri-band W/CDMA/HSPA+/LTE)
GSM 850/GSM 900 Band Electrical Characteristics1
Parameter
Operating frequency range
Input power
Maximum output power
Power added efficiency
(PAE)
Gain
Gain variations – Tc
Gain variations – VBATT
EDGE ACPR2
EDGE EVM
Rx Band noise
Harmonics
Input Impedance
Stability
Ruggedness
Conditions
GSM 850
GSM 900
Min
824
880
Typ
GMSK HPM
GMSK HPM (degraded power)
8PSK (RMS power)
Low Power Mode
GMSK HPM, POUT = PSAT _HPM
GMSK MPM, POUT = PSAT _MPM
8PSK HPM, POUT = 29dBm
GMSK LPM IBATT, POUT = 6dBm
High-power mode POUT = 34.5 dBm
Medium-power mode POUT = 30.5 dBm
Low-Power mode POUT = 14 dBm
-25< Tc < 90°C (all modes)
3.2 < VBATT < 4.2V (all modes)
±400 kHz, POUT ≥ 28dBm
±400 kHz, All power levels
±600 kHz, POUT ≥ 19dBm
±600 kHz, All power levels
All modes
Rx=869-894 MHz
Rx=925-935 MHz
Rx=935-960 MHz
2 fo, POUT ≤34.5dBm
3fo-5fo, POUT ≤34.5dBm
34.5
32.5
35
Max
849
915
9
29
14.0
55
41
28
70
26.5
23.5
13
33.5
31.0
22.0
±1.5
±1
-60
-45
-70
-60
-57
-40
-63
-55
3
-87
-84
-87
-10
-15
2:1
Load VSWR ≤ 8:1 in band, all phase angles
POUT≤34.5dBm
-36
Units
MHz
MHz
dBm
dBm
dBm
dBm
dBm
%
%
%
mA
dB
dB
dB
dB
dB
dBc/30 kHz
dBm/30kHz
dBc/30 kHz
dBm/30kHz
%
dBm/100 kHz
dBm/100 kHz
dBm/100 kHz
dBm
dBm
VSWR
dBm
10:1
Note 1: Performance referenced to module pin under the following conditions unless otherwise specified: T=25°C, Vcc=3.5V, duty =25%,
pulse width =1154us, LB_EN = High
Note 2: ACPR spec referenced in dBc is relaxed by 1dB for every 1dB POUT change for all power levels less than 28dBm for ±400kHz and
all power levels less than 19dBm for ±600kHz. ACPR spec referenced in dBm holds for all power levels and all modes.
Data Sheet
For additional information and the latest specifications, see our website: www.triquint.com
Revision F,September, 2011
4
TQM7M9023
Data Sheet
5.0x7.5mm Multimode Multiband Power Amplifier (MMPA)
(Quad-Band GSM / EDGE and Tri-band W/CDMA/HSPA+/LTE)
DCS 1800/PCS 1900 Band Electrical Characteristics1
Parameter
Operating frequency range
Input power
Maximum output power
Power added efficiency
(PAE)
Gain
Gain variations – Tc
Gain variations – VBATT
EDGE ACPR2
EDGE EVM
Rx band Noise
Harmonics
Input Impedance
Stability
Ruggedness
Conditions
DCS 1800
PCS 1900
Min
1710
1850
Typ
GMSK High Power Mode
GMSK HPM (degraded power)
8PSK (RMS power)
Low Power Mode
GMSK HPM, POUT = PSAT_HPM
GMSK LPM, POUT = PSAT _LPM
8PSK HPM, POUT = 28 dBm
GMSK LPM IBATT, POUT = 1dBm
High Power Mode POUT = 32.0 dBm
Low Power Mode POUT = 14 dBm
-25< Tc < 90°C
3.2 < VBATT < 4.2V
±400 kHz, POUT ≥ 28dBm
±400 kHz, All power levels
±600 kHz, POUT ≥ 14dBm
±600 kHz, All power levels
All modes
Rx=1805-1880 MHz
Rx=1930-1990 MHz
2 fo, POUT ≤32.3dBm
3fo-5fo, POUT ≤32.3dBm
HPM, MPM
LPM
Load VSWR ≤ 8:1 in band, all phase angles
POUT ≤32.3dBm
32.2
30.3
33
14.0
Max
1785
1910
6
28
20
50
23
30
45
27.0
13
32.5
22
±1.5
±1
-60
-45
-73
-60
-57
-40
-65
-55
3
-83
-83
-10
-15
2.0:1
2.5:1
-36
Units
MHz
MHz
dBm
dBm
dBm
dBm
dBm
%
%
%
mA
dB
dB
dB
dB
dBc/30 kHz
dBm/30kHz
dBc/30 kHz
dBm/30kHz
%
dBm/100 kHz
dBm/100 kHz
dBm
dBm
VSWR
VSWR
dBm
10:1
Note 1: Performance referenced to module pin under the following conditions unless otherwise specified: T=25°C, Vcc=3.5V, duty =25%,
pulse width =1154us, HB_EN = High
Note 2: ACPR spec referenced in dBc is relaxed by 1dB for every 1dB POUT change for all power levels less than 28dBm for ±400kHz and
all power levels less than 14dBm for ±600kHz. ACPR spec referenced in dBm holds for all power levels and all modes.
Data Sheet
For additional information and the latest specifications, see our website: www.triquint.com
Revision F,September, 2011
5
TQM7M9023
Data Sheet
5.0x7.5mm Multimode Multiband Power Amplifier (MMPA)
(Quad-Band GSM / EDGE and Tri-band W/CDMA/HSPA+/LTE)
Test Signal Configuration
Parameter
Symbol
Definition
Voice, Rel99
TC1
HPSK modulated carrier in 3.84 MHz BW
UL ref. Meas. Channel (12.2kbps) from 3GPP TS25.101 Annex A sec. A.2.1
1 DPCCH@15ksps, Spread Code=0, Relative Power=-6.547 dB
1 DPDCH@60ksps, Spread Code=16, Relative Power=-1.087 dB
CW testing, input power adjusted to meet output power requirements
HSUPA, MPR=0dB
TC2
DPCCH@15ksps, Spread Code=0, Relative Power=-19.391 dB, Q Branch
DPDCH@960ksps, Spread Code=1, Relative Power=-13.931 dB, I Branch
HS-DPCCH@15ksps, Spread Code=64, Relative Power=-19.391 dB, Q Branch
E-DPCCH@15ksps, Spread Code=1, Relative Power=-17.338 dB, I Branch
E-DPDCH1@960ksps, Spread Code=2, Relative Power=-0.371dB, I branch
CW testing, input power adjusted to meet output power requirements
EVDO Rev A
Data Sheet
Rev A
EVDO Rev A signal using subtype 2 physical layer with a payload size of 4096 bits
For additional information and the latest specifications, see our website: www.triquint.com
Revision F,September, 2011
6
TQM7M9023
Data Sheet
5.0x7.5mm Multimode Multiband Power Amplifier (MMPA)
(Quad-Band GSM / EDGE and Tri-band W/CDMA/HSPA+/LTE)
RF Electrical Characteristics – Band 1 1, 2
Parameter
Power Mode
Frequency
All modes
HPM
HPM
HPM
HPM
HPM
MPM
LPM
All modes
MPM
LPM
HPM
LPM
Maximum Output Power 3
Gain
Noise Power in Rx Band
Quiescent Current (IcQ)
Supply Current
Error Vector Magnitude (EVM)
UMTS Adjacent Channel
Leakage Power Ratio (ACLR)
LTE Adjacent Channel
Leakage Power Ratio (ACLR)
Adjacent Channel Power
Ratio (ACPR)
Harmonic Suppression
Harmonic Suppression
GPS Noise
GPS Band Gain
ISM Noise
ISM Band Gain
All modes
All modes
All modes
H2
H3 and higher
All modes
All modes
Band 34 Noise
All modes
LTE NS_05 PHS Noise4
Input Impedance VSWR
Stability (all spurious)
Coupling Factor
All modes
All modes
All modes
Conditions
Min
Typ
Max
Unit
UMTS Band 1
WCDMA Rel99 waveform 2 (TC1)
Worst case 3GPP; MPR = 0 dB (TC2)
CDMA EVDO revA modulation
LTE, MPR=0dB
POUT ≤ max power
POUT ≤ 17dBm (16dBm 3GPP MPR = 0)
POUT ≤ 8dBm ( 6dBm 3GPP MPR = 0)
190 MHz offset from Tx at all powers
1920
28
27
27
27
24
13
8
1950
1980
G-6
MHz
dBm
dBm
dBm
dBm
dB
dB
dB
dBm/Hz
mA
mA
mA
mA
% rms
dBc
dBc
dBc
dBc
dBc
dBc / 30KHz
dBc / 30kHz
dBc
dBc
dBm/Hz
dB
dBm/Hz
dB
-35
dBm/MHz
-42
dBm/300kHz
-70
dBc
dB
No RF Applied
POUT = 28 dBm
POUT = 3.5dBm
POUT ≤ (maximum power – MPR)
± 5 MHz, Pout ≤ (maximum power - MPR)
± 10 MHz, Pout ≤ (maximum power - MPR)
E-UTRAACLR; POUT ≤ (26.75dBm – MPR)
UTRAACLR1; POUT ≤ (26.75dBm – MPR)
UTRAACLR2; POUT ≤ (26.75dBm – MPR)
HPM ≤27dBm; MPM≤17dBm; LPM≤8dBm
± 1.98MHz; ± 885kHz
POUT ≤ maximum power
POUT ≤ maximum power
1574 – 1577 MHz
Where G is gain in Tx band
2400 – 2483.5 MHz
Where G is gain in Tx band
2010 – 2025 MHz, 100RB QPSK LTE signal
centered at 1970MHz at LTE max power
1884.5 – 1919.6 MHz
No external matching
Load VSWR ≤ 6:1 in band, all phases
29
22
16
-140
15
5
460
8
2.5
-36
-46
-33
-36
-39
-44
-56
-35
-42
-140
G-3
-143
2.0:1
20
Note 1: RF measurements under the following conditions unless otherwise specified: VCC=3.4V, T=25 , Note 1: Rel99 waveform.
Note 2: RF measurements shall be made with 3GPP (UTRAN/FDD UE) TS25.101 specification compliant waveforms. (a) Rel99 waveform
(all beta_c, beta_d combinations) has very low peak-to-average power ratio and has its own requirement. MPR is the maximum power
reduction, worse case MPR = 0dB waveforms across UMTS technologies are required to meet a 1 dB lower maximum power than Rel99.
Signal Configuration: 3GPP (DPCCH + 1DPDCH) Up-Link unless specified otherwise.
Note 3: For VCC < 3.4V operation, up to a 0.5dB back-off is allowed for maximum power output. For VCC=3.4V, T=85°C, up to a 0.5dB back-off is
allowed for maximum power output.
Note 4: POUT ≤ 28dBm for QPSK, 5MHz BW, 8RB; POUT ≤ 23dBm for QPSK, 10MHz BW, 50RB; POUT ≤ 22dBm for QPSK, 20MHz BW, 100RB
Data Sheet
For additional information and the latest specifications, see our website: www.triquint.com
Revision F,September, 2011
7
TQM7M9023
Data Sheet
5.0x7.5mm Multimode Multiband Power Amplifier (MMPA)
(Quad-Band GSM / EDGE and Tri-band W/CDMA/HSPA+/LTE)
RF Electrical Characteristics – Band 5 1, 2
Parameter
Power Mode
Frequency
All modes
HPM
HPM
HPM
HPM
HPM
MPM
LPM
All modes
MPM
LPM
HPM
LPM
Maximum Output Power 3
Gain
Noise Power in Rx Band
Quiescent Current (IcQ)
Supply Current
Error Vector Magnitude (EVM)
UMTS Adjacent Channel
Leakage power Ratio (ACLR)
All modes4
LTE Adjacent Channel
Leakage Power Ratio (ACLR)
All modes
Adjacent Channel Power
Ratio (ACPR)
Harmonic Suppression
Harmonic Suppression
GPS Noise
GPS Band Gain
ISM Noise
ISM Band Gain
Input Impedance VSWR
Stability (all spurious)
Coupling Factor
HPM ≤ 27dBm
MPM ≤ 17dBm
LPM ≤ 8 dBm
H2
H3 and higher
All modes
All modes
All modes
All modes
All modes
Conditions
Min
UMTS Band 5
WCDMA Rel99 waveform (TC1)
Worst case 3GPP; MPR = 0 dB (TC2)
LTE, MPR=0dB
CDMA EVDO revA modulation
POUT ≤ max power
POUT ≤ 17dBm (16dBm 3GPP MPR = 0)
POUT ≤ 9dBm ( 6dBm 3GPP MPR = 0)
190 MHz offset from Tx at all powers
824
28.25
27.25
27.25
27
No RF Applied
POUT = 28.25 dBm
POUT = 3.5dBm
POUT ≤ (maximum power – MPR)
POUT ≤ (maximum power – MPR – 3 dB)
± 5 MHz, POUT ≤ (maximum power - MPR)
± 10 MHz, POUT ≤ (maximum power - MPR)
E-UTRAACLR; POUT ≤ (27dBm – MPR)
UTRAACLR1; POUT ≤ (27dBm – MPR)
UTRAACLR2; POUT ≤ (27dBm – MPR)
Typ
Unit
849
MHz
dBm
dBm
dBm
dBm
dB
dB
dB
dBm/Hz
mA
mA
mA
mA
% rms
% rms
dBc
dBc
dBc
dBc
dBc
dBc/30KHz
dBc/30kHz
27.6
18
11.7
-133
15
5
460
8
3.35
2.5
-36
-46
-33
-36
-39
-44
-56
± 885kHz; Pout ≤ 27dBm
± 1.98MHz; Pout ≤ 27dBm
Pout ≤ maximum power
Pout ≤ maximum power
1574 – 1577 MHz
Where G is gain in Tx band
2400 – 2483.5 MHz
Where G is gain in Tx band
No external matching
Load VSWR ≤ 5:1 in band, all phases
Max
-35
-42
-140
G-25
-143
G-30
2:1
-70
20
dBc
dBc
dBm/Hz
dB
dBm/Hz
dB
dBc
dB
Note 1: RF measurements under the following conditions unless otherwise specified: VCC=3.4V, T=25 , Zin/Zout=50ohm, Rel99
waveform. All measurements are based upon tuning optimized for Band 5 performance. Please see application note for more information.
Note 2: RF measurements shall be made with 3GPP (UTRAN/FDD UE) TS25.101 specification compliant waveforms. (a) Rel99 waveform
(all beta_c, beta_d combinations) has very low peak-to-average power ratio and has its own requirement. MPR is the maximum power
reduction, worse case MPR = 0dB waveforms across UMTS technologies are required to meet a 1 dB lower maximum power than Rel99.
Signal Configuration: 3GPP (DPCCH + 1DPDCH) Up-Link unless specified otherwise.
Note 3: For VCC < 3.4V operation, up to a 0.5dB back-off is allowed for maximum power output. For VCC=3.4V, T=85°C, up to a 0.5dB back-off is
allowed for maximum power output.
Data Sheet
For additional information and the latest specifications, see our website: www.triquint.com
Revision F,September, 2011
8
TQM7M9023
Data Sheet
5.0x7.5mm Multimode Multiband Power Amplifier (MMPA)
(Quad-Band GSM / EDGE and Tri-band W/CDMA/HSPA+/LTE)
RF Electrical Characteristics – Band 8 1, 2
Parameter
Power Mode
Frequency
All modes
HPM
HPM
HPM
HPM
MPM
LPM
All modes
MPM
LPM
HPM
LPM
Maximum Output Power 3
Gain
Noise Power in Rx Band
Quiescent Current (IcQ)
Supply Current
Error Vector Magnitude (EVM)
UMTS Adjacent Channel
Leakage power Ratio (ACLR)
All modes4
LTE Adjacent Channel
Leakage Power Ratio (ACLR)
All modes
Harmonic Suppression
Harmonic Suppression
GPS Noise
GPS Band Gain
ISM Noise
ISM Band Gain
Input Impedance VSWR
Stability (all spurious)
Coupling Factor
H2
H3 and higher
All modes
All modes
All modes
All modes
All modes
Conditions
Min
UMTS Band 8
WCDMA Rel99 waveform (TC1)
Worst case 3GPP; MPR = 0 dB (TC2)
LTE, MPR = 0dB
POUT ≤ max power
POUT ≤ 17dBm (16dBm 3GPP MPR = 0)
POUT ≤ 9dBm ( 6dBm 3GPP MPR = 0)
190 MHz offset from Tx at all powers
880
28.25
27.25
27.25
24.5
13
8
No RF Applied
POUT = 28.25 dBm
POUT = 3.5dBm
POUT ≤ (maximum power – MPR)
POUT ≤ (maximum power – MPR – 3 dB)
± 5 MHz, POUT ≤ (maximum power - MPR)
± 10 MHz, POUT ≤ (maximum power - MPR)
E-UTRAACLR; POUT ≤ (27dBm – MPR)
UTRAACLR1; POUT ≤ (27dBm – MPR)
UTRAACLR2; POUT ≤ (27dBm – MPR)
Pout ≤ maximum power
Pout ≤ maximum power
1574 – 1577 MHz
Where G is gain in Tx band
2400 – 2483.5 MHz
Where G is gain in Tx band
No external matching
Load VSWR ≤ 5:1 in band, all phases
Typ
Max
Unit
915
MHz
dBm
dBm
dBm
dB
dB
dB
dBm/Hz
mA
mA
mA
mA
% rms
% rms
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBm/Hz
dB
dBm/Hz
dB
29.5
22
16
-137
15
5
465
8
3.35
2.5
-36
-46
-33
-36
-39
-35
-42
-140
G-25
-143
G-30
2.0:1
-70
20
dBc
dB
Note 1: RF measurements under the following conditions unless otherwise specified: VCC=3.4V, T=25 , Zin/Zout=50ohm, Rel99
waveform. All measurements are based upon tuning optimized for Band 8 performance. Please see application note for more information.
Note 2: RF measurements shall be made with 3GPP (UTRAN/FDD UE) TS25.101 specification compliant waveforms. (a) Rel99 waveform
(all beta_c, beta_d combinations) has very low peak-to-average power ratio and has its own requirement. MPR is the maximum power
reduction, worse case MPR = 0dB waveforms across UMTS technologies are required to meet a 1 dB lower maximum power than Rel99.
Signal Configuration: 3GPP (DPCCH + 1DPDCH) Up-Link unless specified otherwise.
Note 3: For VCC < 3.4V operation, up to a 0.5dB back-off is allowed for maximum power output. For VCC=3.4V, T=85°C, up to a 0.5dB
back-off is allowed for maximum power output.
Data Sheet
For additional information and the latest specifications, see our website: www.triquint.com
Revision F,September, 2011
9
TQM7M9023
Data Sheet
5.0x7.5mm Multimode Multiband Power Amplifier (MMPA)
(Quad-Band GSM / EDGE and Tri-band W/CDMA/HSPA+/LTE)
Pin Out and Assignments
CPL OUT
GND
RF IN UMTS HB
RF OUT UMTS HB
RF IN GSM HB
GND
HB_EN
VMODE0
RF OUT UMTS LB
VMODE1
GND
Mode
VCC UMTS
GND
VCC GSM
VBATT
GND
RF OUT GSM HB
LB_EN
GND
RF IN GSM LB
RF OUT GSM LB
RF IN UMTS LB
CPL IN
PIN
1
2
3
4
5
6
8
9
7,14,16,19,21,23
10
11
12
13
15
17
18
20
22
24
Data Sheet
SYMBOL
RF IN UMTS HB
RF IN GSM HB
HB_EN
VMODE0
VMODE1
Mode
VBATT
LB_EN
GND
RF IN GSM LB
RF IN UMTS LB
CPL IN
RF OUT GSM LB
RF OUT GSM HB
VCC GSM
VCC UMTS
RF OUT UMTS LB
RF OUT UMTS HB
CPL OUT
DESCRIPTION
RF input for High Band WCDMA amplifier (Band 1)
RF input for DCS/PCS amplifier
Enables HB (DCS/PCS) amplifier
Logic input to set amplifier mode
Logic input to set amplifier mode
Logic input to set amplifier mode – WCDMA or GSM
Battery voltage
Enables LB (GSM) amplifier
GND pin
RF input for GSM850/900 amplifier
RF input for Low Band WCDMA amplifier (Band 5/8)
Coupler Input
RF output for GSM850/900 amplifier
RF output for DCS/PCS amplifier
Voltage supply to Vcc GSM
Voltage supply to Vcc WCDMA
RF output for Low Band WCDMA amplifier (Band 5/8)
RF output for High Band WCDMA amplifier (Band 1)
Coupler Output
For additional information and the latest specifications, see our website: www.triquint.com
Revision F,September, 2011
10
TQM7M9023
Data Sheet
5.0x7.5mm Multimode Multiband Power Amplifier (MMPA)
(Quad-Band GSM / EDGE and Tri-band W/CDMA/HSPA+/LTE)
Package Dimensional Drawings:
Data Sheet
For additional information and the latest specifications, see our website: www.triquint.com
Revision F,September, 2011
11
TQM7M9023
Data Sheet
5.0x7.5mm Multimode Multiband Power Amplifier (MMPA)
(Quad-Band GSM / EDGE and Tri-band W/CDMA/HSPA+/LTE)
Package Land Pattern:
Data Sheet
For additional information and the latest specifications, see our website: www.triquint.com
Revision F,September, 2011
12
TQM7M9023
Data Sheet
5.0x7.5mm Multimode Multiband Power Amplifier (MMPA)
(Quad-Band GSM / EDGE and Tri-band W/CDMA/HSPA+/LTE)
Package Marking
TriQuint:
Product name:
TQM7M9023
Year, Work week,
Country code:
YY= year, WW= work week,
CCCC= country code
Vendor Code and
Assembly #
Aa= Vendor, XXXX= TriQuint
assembly number
Tape and Reel Specification:
613017
Carrier tape - 3M part # 3M053091,
Cavity: Length=5.40mm, Width=7.90mm, Depth=1.40mm, Pitch = 8mm
Carrier Tape: Width = 16mm
Cover tape - 3M part # 2678 13.3mm wide
Note: Packaged quantity is 2,500 per reel
Data Sheet
For additional information and the latest specifications, see our website: www.triquint.com
Revision F,September, 2011
13
TQM7M9023
Data Sheet
5.0x7.5mm Multimode Multiband Power Amplifier (MMPA)
(Quad-Band GSM / EDGE and Tri-band W/CDMA/HSPA+/LTE)
Shipment Box & Label Description:
Tape & Reels will be packaged in a dry-pack bag and then in a shipment box. The box dimensions will depend on the number of reels shipped in
each box and are noted in the table below. The box label and a description of each item on the label are also shown below.
13 Inch x16mm--Drypack
Reel
Empty Box Wt
Qty/Box
w/ Packing
Box Size
15x15x7
3
2
18x15x11
5
2.36
17x16x17
9
2.76
Format: 4 * 6.5 in
102 * 166 mm
Code 39 1:2
Supplier Code: 10
Character Max. +
TQS Shipper Number.
(Pkg. ID/Serial Number)
Customer Purchase
Order. 20 Character
Max.
Customer Part Number. 22
Character Max.
Quantity.
Supplier Product Number.
21 Character Max.
Ship From:
Ship To:
TRIQUINT SEMICONDUCTOR, INC
2300 NE BROOKWOOD PARKWAY
HILLSBORO, OR 97124
Recipient Address
Information Here
(3S) Pkg ID: 581+23047123
(K) Trans ID: 812934657
(P) CPN: 5871-2489
(Q) QTY: 20000
(1P) SPN: TQD777001
MPN: 1005859
Box Count
(1/3, 2/3,
etc.)
All Barcodes Contain
Data Identifier Followed
by Data, e.g.
K812934657
Manufacturer's
Part Number
(13Q) Pkg Count: 1/1
Package Weight
3.0 LB / 1.36 KG
Data Sheet
For additional information and the latest specifications, see our website: www.triquint.com
Revision F,September, 2011
14
TQM7M9023
Data Sheet
5.0x7.5mm Multimode Multiband Power Amplifier (MMPA)
(Quad-Band GSM / EDGE and Tri-band W/CDMA/HSPA+/LTE)
Additional Information 1
This part is compliant with RoHS directive (Restrictions on the Use of Certain Hazardous Substances in Electrical and Electronic
Equipment) and compliant to IPC/JEDEC J-STD-033B.1. The part is rated Moisture Sensitivity Level 3 at 260 degrees C per
JEDEC standard IPC/JEDEC J-STD-020.
1 For latest specifications, additional product information, worldwide sales and distribution locations, and information about TriQuint:
Web: www.triquint.com
Tel: (503) 615-9000
Email: [email protected]
Fax: (503) 615-8902
The information provided herein is believed to be reliable; TriQuint assumes no liability for inaccuracies or omissions. TriQuint assumes no responsibility for the use of this
information, and all such information shall be entirely at the user's own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the
circuits described herein are implied or granted to any third party.
TriQuint does not authorize or warrant any TriQuint product for use in life-support devices and/or systems.
Copyright © 2004 TriQuint Semiconductor, Inc. All rights reserved.
Data Sheet
For additional information and the latest specifications, see our website: www.triquint.com
Revision F,September, 2011
15