Series AM15T-Z 15Watt | DC-DC Converter FEATURES: Wide Input Range 2:1 1600 Vdc Isolation Efficiency up to 91% Soft Start Remote On/Off Function No Minimum Load Required -40ºC to +85ºC Operating Temperature Range Short Circuit & Over Voltage Protection DIP 24 Package Low No Load Input Current Models Single output Model Input Voltage (V) AM15T-1203SZ AM15T-12051SZ AM15T-1212SZ AM15T-1215SZ AM15T-2403SZ AM15T-24051SZ AM15T-2412SZ AM15T-2415SZ AM15T-4803SZ AM15T-48051SZ AM15T-4812SZ AM15T-4815SZ 9-18 9-18 9-18 9-18 18-36 18-36 18-36 18-36 36-75 36-75 36-75 36-75 Output Voltage (V) Output Current max (mA) Isolation (VDC) Maximum Capacitive load (µF) Efficiency (%) 4000 3000 1250 1000 4000 3000 1250 1000 4000 3000 1250 1000 1600 1600 1600 1600 1600 1600 1600 1600 1600 1600 1600 1600 4700 3300 600 400 4700 3300 600 400 4700 3300 600 400 86 89 89 90 87 89 90 91 86 88 89 89 3.3 5.1 12 15 3.3 5.1 12 15 3.3 5.1 12 15 Models Dual output Model Input Voltage (V) Output Voltage (V) Output Current max (mA) Isolation (VDC) Maximum Capacitive load (µF) Efficiency (%) AM15T-1205DZ AM15T-1212DZ AM15T-1215DZ AM15T-2405DZ AM15T-2412DZ AM15T-2415DZ AM15T-4805DZ AM15T-4812DZ AM15T-4815DZ 9-18 9-18 9-18 18-36 18-36 18-36 36-75 36-75 36-75 ±5 ±12 ±15 ±5 ±12 ±15 ±5 ±12 ±15 ±1500 ±625 ±500 ±1500 ±625 ±500 ±1500 ±625 ±500 1600 1600 1600 1600 1600 1600 1600 1600 1600 ±1500 ±288 ±200 ±1500 ±288 ±200 ±1500 ±288 ±200 86 90 90 86 90 90 86 89 90 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified Input Specifications Parameters Voltage range Filter Turn on Transient process time Transient response deviation Start up time Absolute Maximum Rating www.aimtec.com F 051e R12.B Nominal Typical 12 24 48 Maximum 9-18 18-36 36-48 π (Pi) Network 250 VDC ±3 Nominal Vin and constant resistive load 12 Vin models 24 Vin models 48 Vin models Tel: +1 514 620 2722 1 of 3 20 -0.7-36 -0.7-50 -0.7-100 Units µs % ms VDC Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM15T-Z 15Watt | DC-DC Converter Input Specifications (continued) Parameters Nominal Peak Input Voltage time Input reflected ripple current Quiescent Current Typical Maximum Units 1000 20 ms mA p-p mA 15 ON – High (3.0 ... 12Vdc) or open circuit; OFF – Low (0 ... 1.2Vdc) or Short circuit pin1 and pin 2/3 OFF idle current: 5.0 mA typ On/Off Control Isolation Specifications Parameters Tested I/O voltage Tested Case/Input and Output Resistance Capacitance Conditions Typical 3 sec Rated Units 1600 VDC VDC MOhm pF Maximum Units 1600 >1000 2000 Output Specifications Parameters Voltage accuracy Voltage balance Line voltage regulation Load voltage regulation (Single) Load voltage regulation (Dual) Over voltage protection Over current protection Short Circuit protection Short circuit restart Ripple & Noise Conditions Typical ±1 ±5 ±0.5 ±0.5 ±1.0 Zener diode clamp 150 Continuous Auto recovery 60 Dual output HL-LL 0% Load to Full Load 0% Load to Full Load Full Load % % % % % % m Vp-p General Specifications Parameters Switching frequency Operating temperature Storage temperature Max Case temperature Temperature coefficient Derating Cooling Humidity Case material Potting material Weight Dimensions (L x W x H) MTBF www.aimtec.com F 051e R12.B Conditions Typical 100% load Full Load with Derating above 60ºC 330 Maximum -40 to +85 -40 to +125 100 ±0.02 2.5 % per 1ºC Free air convection Above 60ºC Units KHz o C o C o C %/oC 95 % RH Nickel-coated Copper UL94V-0 rated 20.0 g Tolerance ±0.5 mm or ±0.02 inches 1.25 x 0.80 x 0.40 inches 31.80 x 20.30 x 10.20 mm > 460 000 hrs (MIL-HDBK -217F, Ground Benign, t=+25oC) Tel: +1 514 620 2722 2 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM15T-Z 15Watt | DC-DC Converter Safety Specifications Parameters Agency Approval CE IEC 60950-1:2005 (2nd Edition); EN 60950-1: 2006 EN55022 Class A IEC61000-4-2, Perf. Criteria A IEC61000-4-3, Perf. Criteria A IEC61000-4-4, Perf. Criteria B (requires 2 external cap 330uF/100V or 1 cap 680 uF/100V for parallel connection) IEC61000-4-5, Perf. Criteria B (requires 2 external cap 330uF/100V or 1 cap 680 uF/100V for parallel connection) IEC61000-4-6, Perf. Criteria A IEC61000-4-8, Perf. Criteria A Note: also meets IEC 60950-1:2001 Standards Pin Out Specifications Derating Pin Single Dual 1 2 3 9 11 14 16 22 23 Remote On/Off -V Input -V Input No Pin N.C. +V Output -V Output +V Input +V Input Remote On/Off -V Input -V Input Common -V Output +V Output Common +V Input +V Input 3.05 (0.12) 10.20 (0.40) 20.30 (0.80) 15.24 (0.60) Dimensions NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 051e R12.B Tel: +1 514 620 2722 3 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only