Series AM1LS-NZ 1 Watt | DC-DC Converter FEATURES: SMD Package Input / Output Isolation 1000 VDC Low Ripple and Noise Regulated Output Single Output Models Operating temperature -40oC to + 85oC RoHS compliant Continuous Short Circuit Protection Models Single output Model Input Voltage (V) Output Voltage (V) Output Current max (mA) Max Capacitive Load(uF) Isolation (VDC) Efficiency (%) AM1LS-0505S-NZ 4.75-5.25 5 150 1000 33 68 AM1LS-0512S-NZ 4.75-5.25 12 83 1000 33 69 AM1LS-0515S-NZ 4.75-5.25 15 67 1000 33 69 AM1LS-1205S-NZ 11.4-12.6 5 150 1000 33 68 AM1LS-1212S-NZ 11.4-12.6 12 83 1000 33 69 AM1LS-1215S-NZ 11.4-12.6 15 67 1000 33 70 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Parameters Voltage range Nominal Typical 5 12 Maximum Units 4.75 - 5.25 11.4 - 12.6 Capacitor Filter VDC Isolation Specifications Parameters Tested I/O voltage Resistance Capacitance Conditions Typical 60 sec 500VDC 1000 1000 40 Maximum Units VDC MOhm pF Output Specifications Parameters Voltage accuracy Short Circuit protection Short circuit restart Line voltage regulation Load voltage regulation Temperature coefficient Ripple & Noise Conditions Typical 100% load Maximum ±3 Continuous Auto-Recovery ±0.25 ±1 ±0.03 50 For ±5% of Vin 10% - 100% load 100% load 20MHz Bandwidth Units % % of Vin % %/oC mV p-p General Specifications Parameters Switching frequency Operating temperature Storage temperature Derating Cooling Storage Humidity Case material Weight Dimensions (L x W x H) MTBF Maximum soldering temperature Maximum case temperature www.aimtec.com F 051e R12 Conditions Typical 100% load With derating above +71 100 Maximum Units KHz o C o C %/ oC -40 to +85 -55 to +125 2.85 Free air convection 95 Epoxy resin (UL94-V0) 1.7 0.60 x 0.44 x 0.26 inches 15.24 x 11.20 x 6.50 mm >3500K hrs (MIL-HDBK -217F, Ground Benign, t=+25oC)hours 1.5mm from case for 10 sec 260 110 Tel: +1 514 620 2722 1 of 2 % RH g o o C C Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM1LS-NZ 1 Watt | DC-DC Converter Pin Out Specifications and Dimensions Pin 1 2 3 4 5 6 7 8 9 10 Single - V Input + V Input N. C. .-V Output N.C N.C. +V Output N.C. N.C. N.C. Derating NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5.Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 051e R12 Tel: +1 514 620 2722 2 of 2 Toll free: + 1 888 9 AIMTEC (924 6832) North America only