Series AMLB-IZ 100mA | LED Driver FEATURES: • • • • Step Up LED Driver Wide (7:1) Input Voltage Range Remote Control Function 24 Pin DIP Package • • • • Models Single output Model Input Voltage (V) Output Voltage (V) 3-18 5-38 AMLB-1810IZ Constant Output Current High Efficiency PWM Dimming Function (10 – 90%) Non-Isolated Maximum Rated Current (mA) Efficiency Max (%) 100 90 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Parameters Voltage range On/Off Control (Analog Control) Input voltage range (0-12Vdc) (Leave open if not used) Dimming Control (Digital Control) Output Specifications Parameters Current accuracy Short Circuit protection Output Open Protection Max load capacitance General Specifications Parameters Switching frequency Operating temperature Nominal 12 Typical Maximum 3-18 Units 18 VDC ON: Vr = DC Input Voltage OFF:DC = 0V Max PWM Frequency (10%~90%) 200Hz Conditions Conditions 100% load Typical Maximum Units ±5 Connect an external input fuse (1A/250) No Load 100 Typical 1.2 % µF Maximum Units MHz o C -40 to +85 95 Non-Conductive Black Plastic Epoxy (Flammability UL94V-0) 12 1.25 × 0.80 × 0.45 inches / 31.80 × 20.30 × 11.30 mm www.aimtec.com Tel: +1 514 620 2722 F 051e R12.B -40 to +125 o Storage temperature Max Case temperature Cooling Humidity Case material Potting material Weight Dimensions (L x W x H) Free Air Convection 1 of 3 o 100 C C % RH g Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLB-IZ 100mA | LED Driver Pin Out Specifications Dimensions 31.80 (1.25) Pin Single 1 Remote On/Off 2 -Vin 3 -Vin 9 NC 11 NC 14 LED + 16 LED 22 +Vin 23 +Vin 24 DIM NC: Not Connected 1 2 3 20.30 (0.80) 9 11 15.24 (0.60) Bottom View 24 23 0.50 (0.02) 22 16 2.54 (0.1) 14 5.08 (0.2) 11.30 (0.45) 3.80 (0.15) Derating Free Air Convection 85 º C Output Power % 100 80 60 Safe Operating Area 40 20 0 -40 -25 0 25 50 75 85 100 Ambient Temperature º C www.aimtec.com F 051e R12.B Tel: +1 514 620 2722 2 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLB-IZ 100mA | LED Driver Application Circuit + Vin 1st LED Dimming C1 0.01uF Dim If analogue DIM is not used C1 must be installed + Vin LED + AMLB-IZ ON/OFF ON/OFF LED - GND Leave Open if not used Last LED GND Dimming Performance AMLB-1810-IZ Dimming 100 90 80 Output Current 70 60 50 40 30 20 10 0 1 2 3 4 5 6 7 8 9 10 11 Duty Cycle PWM @ 200 Hz NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 051e R12.B Tel: +1 514 620 2722 3 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only