LMP8100 Programmable Gain Amplifier General Description Features The LMP8100 programmable gain amplifier features an adjustable gain from 1 to 16 V/V in 1 V/V increments. At the core of the LMP8100 is a precision, 33 MHz, CMOS input, rail-torail input/output operational amplifier with a typical open-loop gain of 110 dB. Amplifier closed-loop gain is set by an array of precision thin-film resistors. Amplifier control modes are programmed via a serial port that allows devices to be cascaded so that an array of LMP8100 amplifiers can be programmed by a single serial data stream. The control mode registers are double buffered to insure glitch-free transitions between programmed settings. The LMP8100 is part of the LMP® precision amplifier family and is ideal for a variety of applications. Typical Values, TA = 25°C ■ Gain error (over temperature range) 0.03% — LMP8100A 0.075% — LMP8100 1 to 16 V/V in 1 V/V steps ■ Gain range ■ Programmable frequency compensation ■ Input zero calibration switch 250 μV ■ Input offset voltage (max, LMP8100A) 0.1 pA ■ Input bias current 12 nV/√Hz ■ Input noise voltage 33 MHz ■ Unity gain bandwidth 12 V/μs ■ Slew rate 20 mA ■ Output current 2.7V to 5.5V ■ Supply voltage range 5.3 mA ■ Supply current + − Rail-to-Rail output swing V −50 mV to V +50 mV ■ The amplifier features several programmable controls including: gain; a power-conserving shutdown mode which can reduce current consumption to only 20 μA; an input zeroing switch which allows the output offset voltage to be measured to facilitate system calibration; and four levels of internal frequency compensation which can be set to maximize bandwidth at the different gain settings. The LMP8100 comes in a 14-Pin SOIC package. Applications ■ ■ ■ ■ ■ ■ Industrial instrumentation Data acquisition systems Test equipment Scaling amplifier Gain control Sensor interface Simplified Block Diagram 20147607 LMP® is a registered trademark of National Semiconductor Corporation. © 2008 National Semiconductor Corporation 201476 www.national.com LMP8100 Programmable Gain Amplifier April 18, 2008 LMP8100 Block Diagram 20147602 www.national.com 2 If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. ESD Tolerance (Note 2) Human Body Model Machine Model VIN Differential Output Short Circuit Duration (Note 3) Supply Voltage (VS = V+ – V−) Voltage at Input and Output Pins Input Current Storage Temperature Range Junction Temperature (Note 4) Operating Ratings 2 kV 200V 2.5V 235°C 260°C (Note 1) Supply Voltage (VS = V+ – V−) Junction Temperature Range (Note 4) LMP8100A LMP8100 6V V+ +0.3V, V− −0.3V ±10 mA −65°C to +150°C +150°C 2.7V to 5.5V −40°C to +125°C −40°C to +85°C Package Thermal Resistance (θJA (Note 4) 14-Pin SOIC 145°C/W 5V Electrical Characteristics Unless otherwise specified, all limits are guaranteed for TA = 25°C. V+ = 5V , V– = 0V, DGND = 0V, +IN = GRT = V+/2, RL = 10 kΩ to V+/2; Gain = 1 V/V. Boldface limits apply at the temperature extremes. Symbol Parameter Gain Error Gain Error TCGE VOS Conditions Min (Note 6) Typ (Note 5) Max (Note 6) LMP8100A 0V < +IN (DC) < 3.5V, 0.015 0.03 0.03 LMP8100 1 V/V ≤ Gain ≤ 16 V/V, 0.5V < VOUT < 4.5V 0.015 0.075 0.075 % LMP8100 Gain Error (Gain = 1 V/V) Extended +IN Range +IN > 3.5V, 0.3V < VOUT < 4.7V Gain Drift LMP8100A Gain = 16 0.5 2.2 LMP8100 Gain = 16 0.8 4.8 LMP8100A ±50 ±250 ±450 LMP8100 ±50 ±400 ±600 1.5 5 µV/°C 0.1 5 100 pA Input Offset Voltage TCVOS Input Offset Temp Coefficient IB Input Bias Current en Input-Referred Noise Voltage 0.1 0.2 Units (Note 8) f = 10 kHz, 1 V/V ≤ Gain ≤ 16 V/V 12 f = 0.1 Hz to 10 Hz, 1 V/V ≤ Gain 3.8 C1 = C0 = 0, Gain = 1 V/V 33 C1 = C0 = 0, Gain = 2 V/V 15.5 C1 = C0 = 1, Gain = 16 V/V 9.5 % ppm/°C µV nV/ µVPP ≤ 16 V/V BW Bandwidth SR Slew Rate (Note 7) PSRR Power Supply Rejection Ratio 2.7V < V+ < 5.5V VO Output Swing High +IN = 5V Output Swing Low +IN = 0V IO Output Current Sourcing and Sinking VIN Input Voltage Range IS Supply Current MHz 12 90 85 100 4.9 4.85 4.95 50 15 dB V 100 150 20 –0.2 0 5.3 3 V/µs mV mA 5.2 5.0 V 6.0 7.2 mA www.national.com LMP8100 Soldering Information Lead Temperature, Infrared or Convection Reflow (20 sec) Lead Temperature, Wave Solder (10 sec) Absolute Maximum Ratings (Note 1) LMP8100 Symbol IPD Parameter Conditions Min (Note 6) Supply Current, Power Down Feedback Resistance RIN Input Impedance f = 10 Hz Typ (Note 5) Max (Note 6) 3.5 20 40 Units µA 5.6 kΩ >10 GΩ 3.3V Electrical Characteristics Unless otherwise specified, all limits are guaranteed for TA = 25°C. V+ = 3.3V , V– = 0V, DGND = 0V, +IN = GRT = V+/2, RL = 10 kΩ to V+/2; Gain = 1 V/V. Boldface limits apply at the temperature extremes. Symbol Parameter Gain Error Gain Error TCGE VOS Typ (Note 5) Max (Note 6) 0V < +IN < 1.8V, 0.015 0.03 0.03 LMP8100 1 V/V ≤ Gain ≤ 16 V/V, 0.3V < VOUT < 3.0V 0.015 0.075 0.075 % +IN > 1.8V, 0.3V < VOUT < 3.0V Gain Drift LMP8100A Gain = 16 0.5 2.2 LMP8100 Gain = 16 0.8 4.8 LMP8100A ±50 ±250 ±450 LMP8100 ±50 ±400 ±600 1.5 5 µV/°C 0.1 5 100 pA Input Offset Voltage Input Offset Temp Coefficient Input Bias Current en Input-referred Noise Voltage Bandwidth 0.1 0.2 Units LMP8100 Gain Error (Gain = 1 V/V) Extended +IN Range IB (Note 8) f = 10 kHz, 1 V/V ≤ Gain ≤ 16 V/V 12 f = 0.1 Hz to 10 Hz, 1 V/V ≤ Gain ≤ 16 V/V 3.8 C1 = C0 = 0, Gain = 1 V/V 33 C1 = C0 = 0, Gain = 2 V/V 15.5 C1 = C0 = 1, Gain = 16 V/V 9.5 SR Slew Rate (Note 7) PSRR Power Supply Rejection Ratio 2.7V < V+ < 3.6V VO Output Swing High +IN = 3.3V Output Swing Low +IN = 0V IO Output Current Sourcing and Sinking VIN Input Voltage Range IS Supply Current IPD Supply Current, Power Down RIN Min (Note 6) LMP8100A TCVOS BW Conditions 100 3.2 3.15 3.25 50 15 µV µVPP MHz V/µs dB V 100 150 20 −0.2 0 ppm/°C nV/ 12 90 80 % mV mA 3.5 3.3 V 5.1 5.8 7.0 mA 1.8 20 40 µA Feedback Resistance 5.6 kΩ Input Impedance >10 GΩ www.national.com 4 Unless otherwise specified, all limits guaranteed for TA = 25°C, V+ - V− ≥ 2.7V, VD = V+ - DGND ≥ 2.5V. Symbol Parameter Conditions Min (Note 6) Typ (Note 5) Max (Note 6) Units 0.3 × VD V VIL Logic Low Threshold VIH Logic High Threshold ISDO Output Source Current, SDO VD = 3.3V or 5.0V, CS = 0V, VOH = V+ – 0.7V −7 Output Sink Current, SDO VD = 3.3V or 5.0V, CS = 0V, VOL = 1.0V 10 IOZ Output Tri-state Leakage Current, SDO VD = 3.3V or 5.0V, CS = VD = 3.3V or 5V t1 High Period, SCK (Note 9) 100 ns t2 Low Period, SCK (Note 9) 100 ns t3 Set Up Time, CS to SCK (Note 9) 50 ns t4 Set Up Time, SDI to SCK (Note 9) 30 ns t5 Hold Time, SCK to SDI (Note 9) 10 ns t6 Prop. Delay, SCK to SDO (Note 9) t7 Hold Time, SCK Transition to CS Rising Edge (Note 9) 50 t8 CS Inactive (Note 9) 50 t9 Prop. Delay, CS to SDO Active (Note 9) t10 Prop. Delay, CS to SDO Inactive (Note 9) t11 Hold Time, SCK Transition to CS Falling Edge (Note 9) 10 Signal Rise and Fall Times (Note 9) 1.5 tR/tF 0.7 × VD V mA ±1 µA 60 ns ns ns 50 ns 50 ns ns 5 ns Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but for which specific performance is not guaranteed. For guaranteed specifications and the test conditions, see Electrical Characteristics. Note 2: Human Body Model, applicable std. MIL-STD-883, Method 3015.7. Machine Model, applicable std. JESD22–A115–A (ESD MM std. of JEDEC). FieldInduced Charge-Device Model, applicable std. JESD22–C101–C (ESD FICDM std. of JEDEC). Note 3: The short circuit test is a momentary test which applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can exceed the maximum allowable junction temperature of 150°C. Note 4: The maximum power dissipation is a function of TJ(MAX), θJA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(MAX) – TA)/ θJA. All numbers apply for packages soldered directly onto a PC Board. Note 5: Typical Values indicate the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will also depend on the application and configuration. The typical values are not tested and are not guaranteed on shipped production material. Note 6: All limits are guaranteed by testing or statistical analysis. Note 7: Slew rate is the average of the rising and falling slew rates. Note 8: The offset voltage average drift is determined by dividing the value of VOS at the temperature extremes by the total temperature change. Note 9: Load for these tests is shown in the Timing Diagram Test Circuit. 5 www.national.com LMP8100 Electrical Characteristics (Serial Interface) LMP8100 Connection Diagram 14-Pin SOIC 20147601 Top View Ordering Information Package Part Number LMP8100AMA 14-Pin SOIC LMP8100AMAX LMP8100MA LMP8100MAX www.national.com Package Marking LMP8100AMA Transport Media 2.5k units Tape and Reel 55 Units/Rail LMP8100MA 2.5k units Tape and Reel 6 NSC Drawing 55 Units/Rail M14A LMP8100 Timing Diagram Test Circuit 20147653 Timing Diagram 20147603 7 www.national.com LMP8100 Test Circuit Diagram 20147609 Test Circuit www.national.com 8 LMP8100 Typical Performance Characteristics Offset Voltage Distribution Offset Voltage Distribution 20147685 20147686 TCVOS Distribution TCVOS Distribution 20147683 20147684 VOS vs. VIN VOS vs. VIN 20147666 20147667 9 www.national.com LMP8100 VOS vs. VS VOS vs. VS 20147665 20147664 IB vs. VIN IB vs. VIN 20147662 20147663 IS vs. VS IS vs. VS 20147660 www.national.com 20147661 10 LMP8100 DC Gain Error A = 1 DC Gain Error A = 1 20147687 20147689 DC Gain Error A = 2 DC Gain Error A = 2 20147688 20147690 Small Signal Gain Error vs. +IN DC Level Small Signal Gain Error vs. +IN DC Level 20147651 20147633 11 www.national.com LMP8100 PSRR vs. Frequency PSRR vs. Frequency 20147611 20147610 IOUT vs. VOUT (Source) IOUT vs. VOUT (Sink) 20147669 20147668 IOUT vs. VOUT (Source) IOUT vs. VOUT (Sink) 20147671 www.national.com 20147670 12 LMP8100 Small Signal Step Response Small Signal Step Response 20147635 20147636 Small Signal Step Response Small Signal Step Response 20147638 20147637 Small Signal Step Response Small Signal Step Response 20147639 20147640 13 www.national.com LMP8100 Small Signal Step Response Small Signal Step Response 20147642 20147641 Large Signal Step Response Large Signal Step Response 20147643 20147644 Large Signal Step Response Large Signal Step Response 20147645 www.national.com 20147646 14 LMP8100 Large Signal Step Response Large Signal Step Response 20147648 20147647 Large Signal Step Response Large Signal Step Response 20147650 20147649 THD+N vs. Frequency THD+N vs. Frequency 20147674 20147675 15 www.national.com LMP8100 THD+N vs. VOUT THD+N vs. VOUT 20147673 20147672 Bandwidth vs. Capacitive Load Bandwidth vs. Capacitive Load 20147617 20147618 Peaking vs. Capacitive Load Peaking vs. Capacitive Load 20147622 20147621 www.national.com 16 LMP8100 Peaking vs. Capacitive Load Gain vs. Frequency 20147630 20147623 Gain vs. Frequency Gain vs. Frequency 20147629 20147628 Gain vs. Frequency AC Gain Error vs. Frequency 20147656 20147627 17 www.national.com LMP8100 AC Gain Error vs. Frequency AC Gain Error vs. Frequency 20147655 20147657 AC Gain Error vs. Frequency AC Gain Error vs. Frequency 20147658 20147659 Noise vs. Frequency 0.1 Hz to 10 Hz Noise 201476a2 20147654 www.national.com 18 LMP8100 Closed Loop Output Impedance vs. Frequency Input Impedance 20147631 201476a1 SDO V vs. I SDO V vs. I 20147634 20147652 19 www.national.com LMP8100 Applications Information LIFETIME DRIFT Offset voltage (VOS) and gain are electrical parameters which may drift over time. This drift, known as lifetime drift, is very common in operational amplifiers; however, its effect is more evident in precision amplifiers. This is due to the very low offset voltage specification and very precise gain specification of the LMP8100. The LMP8100 has an option to zero out the offset voltage. When the zero bit of the register is set high, +IN is connected to GRT. Output offset voltage can be measured and adjusted out of the signal path. See the “Input Zeroing” section, for more information. Numerous reliability tests have been performed to characterize this drift for the LMP8100. Prior to each long term reliability test the input offset voltage and gain at 2X and 16X of each LMP8100 was measured at room temperature. The long term reliability tests include Operating Life Time (OPL) performed at 150°C for an extended period of time and Temperature Humidity Bias Testing (THBT) at 85°C and 85% humidity for an extended period of time. The offset voltage and gain of 2X and 16X were measured again at room temperature after each reliability test. The offset voltage drift is the difference between the initial measurement and the later measurement, after the reliability test. The gain drift is the percentage difference between the initial measurement and the later measurement, after the reliability test. Figure 1 – Figure 4 show the offset voltage drift and gain drift after 1000 hours of OPL. Figure 5 – Figure 8 show the offset voltage drift and gain drift after 1000 hours of THBT. 20147692 FIGURE 2. OPL VOS Drift 20147693 FIGURE 3. OPL Gain Drift, A = 2 20147691 FIGURE 1. OPL VOS Drift 20147694 FIGURE 4. OPL Gain Drift, A = 16 www.national.com 20 LMP8100 20147695 20147698 FIGURE 5. THBT VOS Drift FIGURE 8. THBT Gain Drift, A = 16 POWER-ON RESET The LMP8100 has a power-up reset feature that sets all the register bits to 0 when the part is powered up. To implement this feature the CS and SCK pins must be held at or above VIH when the LMP8100 is powered-up. Failure to power up in this method can lead to an unpredictable state of the register bits after power-up. CONTROL REGISTER The control register retains the information which controls the amplifier gain, bandwidth compensation, input zeroing, and power down. The register is loaded by way of the serial control interface. The register is double buffered so that changes can be made with minimum effect on amplifier performance. Table 1 shows the organization of the control register. Table 2 gives the codes for gain setting, input zeroing and power down control. Table 3 shows the codes for the four gain-bandwidth compensation levels. 20147696 TABLE 1. Control Register Format FIGURE 6. THBT VOS Drift C1 C0 Zero PD MSB G3 G2 G1 G0 LSB C0, C1: Compensation setting Zero: Zero Input PD: Power Down G0 to G3: Gain setting 20147697 FIGURE 7. THBT Gain Drift, A = 2 21 www.national.com LMP8100 TABLE 4. Amplifier Gain and Compensation vs. Bandwidth TABLE 2. Input Zero, Power-Down and Gain Setting Codes Zero PD G3 G2 G1 G0 Non-Inverting Gain 0 0 0 0 0 1 V/V dB C1 C0 0 0 0 0 1 2 1 0 0 0 33.0 0 0 0 1 0 3 0 0 0 1 1 4 2 6.02 0 0 15.5 0 0 1 0 0 5 0 0 1 0 1 6 6 15.6 0 0 4.2 0 0 1 1 0 7 6 15.6 0 1 8.3 0 0 1 1 1 8 0 1 0 0 0 9 11 20.8 0 0 2.0 0 1 0 0 1 10 11 20.8 0 1 3.9 0 1 0 1 0 11 11 20.8 1 0 6.6 0 1 0 1 1 12 0 1 1 0 0 13 16 24.1 0 0 1.3 0 1 1 0 1 14 16 24.1 0 1 2.3 0 1 1 1 0 15 16 24.1 1 0 3.8 16 24.1 1 1 9.5 0 1 1 1 1 16 X 1 X X X X Power Down 1 0 X X X X Zero Input Gain C0 Compensation Level 0 0 0 0 1 1 1 0 2 1 1 3 Condition Maximum Compensation Minimum Compensation AMPLIFIER GAIN SETTING AND BANDWIDTH COMPENSATION CONTROL The gain of the LMP8100 is set to one of 16 levels under program control by setting the appropriate bits G[3:0] of the control register with a number from 00h to 15h. This sets the gain to a level from 1 V/V to 16 V/V respectively. The gain-bandwidth compensation is also selectable to one of four levels under program control. The amount of compensation can be decreased to maximize the available bandwidth as the gain of the amplifier is increased. The compensation level is selected by setting bits C[1:0] of the control register with a number from 00b to 11b with 00b being maximum compensation and 11b being minimum compensation. Table 4 shows the bandwidths achieved at several gain and compensation settings. It will be noted that for gains between X1 and X5, the recommended compensation setting is 00b. For gain settings between X6 and X10, compensation settings may be 00b and 01b. Gain settings between X11 and X15 may use the three bandwidth compensation settings between 00b and 10b. At a gain of X16, all bandwidth compensation ranges may be used. Note that, for lower gains, it is possible to undercompensate the amplifier into instability. www.national.com 3 dB Bandwidth (MHz) NON-INVERTING AMPLIFIER OPERATION The principal application of the LMP8100 is as a non-inverting amplifier as shown in the simplified schematic, Figure 9. The amplifier supply voltage (V+ to V−) is specified as 5.5V maximum. The V– supply pin is connected to the system ground for single supply operation. V− can be returned to a negative voltage when required by the application. The digital supply voltage for the serial interface is applied between the V+ supply pin and DGND. TABLE 3. Amplifier Gain Compensation Codes C1 Compensation Bits 20147605 FIGURE 9. Basic Non-Inverting Amplifier 22 Any resistance between the GRT pins and either ground or a reference voltage will change the gain to 20147676 FIGURE 11. GRT Connection Methods The GRT pin can be connected to a reference voltage source to provide an offset adjustment to the gain function. Any DC resistance that may be present between the voltage source and the GRT pin must be kept to an absolute minimum to avoid introducing gain errors into the circuit. INPUT ZEROING Measurements made with the LMP8100 in the signal path may be adjusted for the output offset voltage of the amplifier. For example: The measurement of VOUT for offset correction might be made using an ADC under microprocessor control. Output offset is measured under program control by setting the ZERO bit in the programming register. In this mode, +IN is disconnected from the input pin and internally connected to the GRT input. Figure 12 shows the LMP8100 in the input zeroing mode. 20147679 FIGURE 10. LMP8100 with External Parasitical Resistance The connection between the GRT pins and ground or a reference voltage should be as short as possible using wide 23 www.national.com LMP8100 traces to minimize the parasitical resistance. Figure 11 shows two suggested methods of connecting the GRT pins to a ground plane on the same layer or to a ground plane on a different layer of the PCB. GRT PINS The GRT pins must have a low impedance connection to either ground or a reference voltage. Any parasitical impedance on these pins will affect the gain accuracy of the LMP8100. Figure 10 shows a simplified schematic of the LMP8100 showing the internal gain resistors and an external parasitical resistance RP. The gain of the LMP8100 is determined by RF and RG, the values of which are set by the internal register. The gain of the amplifier is given by the equation LMP8100 20147606 FIGURE 12. Non-Inverting Input Zeroing Function The serial clock, SCK controls the serial loading process. All eight data bits are required to correctly program the amplifier. The falling edge of CS enables the shift register to receive data. The SCK signal must be high during the falling and rising edge of CS. Each data bit is clocked into the shift register on the rising edge of SCK. Data is transferred from the shift register to the holding register on the rising edge of CS. Operation is shown in the timing diagram,Figure 13. SERIAL CONTROL INTERFACE OPERATION The LMP8100 gain, bandwidth compensation, power down, and input zeroing are controlled by data stored in a programming register. Data to be written into the control register is first loaded into the LMP8100 via the serial interface. The serial interface employs an 8-bit shift register. Data is loaded through the serial data input, SDI. Data passing through the shift register is output through the serial data output, SDO. 20147624 FIGURE 13. Serial Control Interface Timing www.national.com 24 shown in Figure 14. After the microcontroller writes a byte all registers will have the same value. Star Configuration This configuration can be used if each LMP8100 will always have the same value in each register. The connections are 20147680 FIGURE 14. Star Configuration Daisy Chain Configuration lowing LMP8100. The following two examples show how the registers are written. This configuration can be used to program the same or different values in the register of each LMP8100. The connections are shown in Figure 15. In this configuration the SDO pin of each LMP8100 is connected to the SDI pin of the folIf all three LMP8100s need a gain of 11 with a compensation level of 10. (10001010) Register of LMP8100 #1 Register of LMP8100 #2 Register of LMP8100 #3 Notes Power on 00000000 00000000 00000000 Default power on state (see above) Byte one sent 10001010 00000000 00000000 Byte two sent 10001010 10001010 00000000 Byte three sent 10001010 10001010 10001010 The data in the register of LMP8100 #1 is shifted into the register of LMP8100 #2, the data in the register of LMP8100 #2 is shifted into the register of LMP8100 #3. If LMP8100 #1 needs a gain of 11 with a compensation level of 10 (10001010), LMP8100 #2 needs a gain of 6 with a compensation of 00 (00000101), and LMP8100 #3 needs a gain of 2 with a compensation of 00 (00000001). Register of LMP8100 #1 Register of LMP8100 #2 Register of LMP8100 #3 Notes Power on 00000000 00000000 00000000 Default power on state (see above) Byte one sent 00000001 00000000 00000000 Byte two sent 00000101 00000001 00000000 Byte three sent 10001010 00000101 00000001 The data in the register of LMP8100 #1 is shifted into the register of LMP8100 #2, the data in the register of LMP8100 #2 is shifted into the register of LMP8100 #3. 25 www.national.com LMP8100 The serial control pins can be connected in one of two ways when two or more LMP8100s are used in an application. LMP8100 20147681 FIGURE 15. Daisy Chain Configuration POWER SUPPLY PURITY AND BYPASSING Particular attention to power supply purity is needed in order to preserve the LMP8100's gain accuracy and low noise. The LMP8100 worst-case PSRR is 85 dB or 56.2 µV/V. Nevertheless, the usable dynamic range, gain accuracy and inherent low noise of the amplifier can be compromised through the introduction and amplification of power supply noise. To decouple the LMP8100 from supply line AC noise, a 0.1 µF capacitor should be located on each supply line, close to the LMP8100. Adding a 10 µF capacitor in parallel with the 0.1 µF capacitor will reduce the noise introduced to the LMP8100 even more by providing an AC path to ground for most frequency ranges. A power supply dropout (V+ -V− < 2.7V) can cause an unintended reset of the register. If a dropout occurs, the register will need to be reprogrammed with the correct values. SCALING AMPLIFIER The LMP8100 is ideally suited for use as an amplifier between a sensor that has a wide output range and an ADC. As the signal from the sensor changes the gain of the LMP8100 can be changed so that the entire input range of the ADC is being used at all times. Figure 16 shows a data acquisition system using the LMP8100 and the ADC121S101. The 100Ω resistor and 390 pF capacitor form an antialiasing filter for the ADC121S101. The capacitor also stores and delivers charge to the switched capacitor input of the ADC. The capacitive load on the LMP8100 created by the 390pF capacitor is decreased by the 100Ω resistor. 20147682 FIGURE 16. Data Acquisition System Using the LMP8100 www.national.com 26 Make the traces between the Magnetic Field Sensor and the LMP8100s short to minimize noise pickup. • Place 0.1 μF capacitors close to each of the LMP8100 supply pins. The following can be done to simplify the design: • Connect the SCL, SCK, and CS lines in parallel and one microcontroller can be used to drive both LMP8100s. • The SDO pin can be left floating. The LM317 and LM6171 are used for the supply of the Magnetic Sensor. The 100Ω potentiometer is used to adjust the supply voltage to the Magnetic Field Sensor. The 2 kΩ potentiometer is used to fine tune the negative supply to set the Magnetic Field Sensor output to zero. 20147625 FIGURE 17. Bridge Amplifier 27 www.national.com LMP8100 • BRIDGE AMPLIFIER In Figure 17 two LMP8100s are used with a LMP7711 to build an amplifier for the signal from a GMR Magnetic Field Sensor. The advantage of using the LMP8100 is that as the signal strength from the Magnetic Field Sensor decreases, the gain of the LMP8100 can be increased. An example is if the signal from this composite amplifier is used to drive an ADC. When the maximum magnetic field to be measured is applied, the gain of the LMP7711 can be set to supply a full range signal to the ADC input with the gain of the LMP8100 set to one. As the magnetic field decreases, the gain of the LMP8100 can be increased, so that the signal supplied to the ADC uses a maximum amount of the ADC input range. The following can be done to maximize performance: • Connect the GRT pins directly together and to GND with a low impedance trace. LMP8100 Physical Dimensions inches (millimeters) unless otherwise noted 14-Pin SOIC NS Package Number M14A www.national.com 28 LMP8100 Notes 29 www.national.com LMP8100 Programmable Gain Amplifier Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH www.national.com/webench Audio www.national.com/audio Analog University www.national.com/AU Clock Conditioners www.national.com/timing App Notes www.national.com/appnotes Data Converters www.national.com/adc Distributors www.national.com/contacts Displays www.national.com/displays Green Compliance www.national.com/quality/green Ethernet www.national.com/ethernet Packaging www.national.com/packaging Interface www.national.com/interface Quality and Reliability www.national.com/quality LVDS www.national.com/lvds Reference Designs www.national.com/refdesigns Power Management www.national.com/power Feedback www.national.com/feedback Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www.national.com/led PowerWise www.national.com/powerwise Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors Wireless (PLL/VCO) www.national.com/wireless THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION (“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright© 2008 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: [email protected] German Tel: +49 (0) 180 5010 771 English Tel: +44 (0) 870 850 4288 National Semiconductor Asia Pacific Technical Support Center Email: [email protected] National Semiconductor Japan Technical Support Center Email: [email protected]