Preliminary Datasheet 340kHz, 3A Synchronous DC-DC Buck Converter General Description Features The AP3503E is a 340kHz fixed frequency, current mode, PWM synchronous buck (step-down) DC-DC converter, capable of driving a 3A load with high efficiency, excellent line and load regulation. The AP3503E exhibits high efficiency at light load. The device integrates N-channel power MOSFET switches with low on-resistance. Current mode control provides fast transient response and cycle-by-cycle current limit. • • • • • • • • • • • • The AP3503E employs complete protection to ensure system security. Including output Over Voltage Protection, input Under Voltage Lock Out, programmable Soft Start, Over Temperature Protection and hiccup mode Short Circuit Protection. AP3503E Input Voltage Range: 4.5V to 18V Fixed 340kHz Frequency High Efficiency at Light Load High Efficiency: up to 95% Output Current: 3A Current Mode Control Built-in Over Current Protection Built-in Thermal Shutdown Function Built-in UVLO Function Built-in Over Voltage Protection Programmable Soft-start Hiccup Mode SCP Applications • • • • This IC is available in PSOP-8 package. LCD TV Set Top Box Portable DVD Digital Photo Frame PSOP-8 Figure 1. Package Type of AP3503E May. 2012 Rev. 1. 6 BCD Semiconductor Manufacturing Limited 1 Preliminary Datasheet 340kHz, 3A Synchronous DC-DC Buck Converter AP3503E Pin Configuration MP Package (PSOP-8) 1 8 2 7 3 6 4 5 Figure 2. Pin Configuration of AP3503E (Top View) Pin Description Pin Number Pin Name 1 BS 2 IN 3 SW 4 GND 5 FB 6 COMP 7 EN 8 SS EP May. 2012 Function Bootstrap pin. A bootstrap capacitor is connected between the BS pin and SW pin. The voltage across the bootstrap capacitor drives the internal high-side power MOSFET Supply power input pin. A capacitor should be connected between the IN pin and GND pin to keep the input voltage constant Power switch output pin. This pin is connected to the inductor and bootstrap capacitor Ground pin Feedback pin. This pin is connected to an external resistor divider to program the system output voltage. When the FB pin voltage exceeds 1.1V, the over voltage protection is triggered. When the FB pin voltage is below 0.3V, the oscillator frequency is lowered to realize short circuit protection Compensation pin. This pin is the output of the transconductance error amplifier and the input to the current comparator. It is used to compensate the control loop. Connect a series RC network from this pin to GND. In some cases, an additional capacitor from this pin to GND pin is required Control input pin. EN is a digital input that turns the regulator on or off. Drive EN high/low to turn on/off the regulator. Pull up with 100kΩ resistor for automatic startup Soft-start control input pin. SS controls the soft-start period. Connect a capacitor from SS to GND to set the soft-start period. A 0.1µF capacitor sets the soft-start period to 15ms. To disable the soft-start feature, leave SS unconnected Exposed pad. It should be connected to GND in PCB layout Rev. 1. 6 BCD Semiconductor Manufacturing Limited 2 Preliminary Datasheet 340kHz, 3A Synchronous DC-DC Buck Converter AP3503E Functional Block Diagram IN 2 SHUTDOWN COMPARATOR 1.5V VA INTERNAL REGULATOR 0.3V VB CURRENT SENSE AMPLIFIER SLOP COMP VA + OSCILLATOR SCP 90K/340K 1 BS M1 CLK LOCK EN COMPARATOR 7 S Q R Q 3 PWM COMPARATOR SW M2 2.5V VB 4 1.1V 5 A SS 8 GND EA 5 0. 925V FB 6 COMP Figure 3. Functional Block Diagram of AP3503E Ordering Information AP3503E - Circuit Type G1: Green Package MP: PSOP-8 Package Temperature Range PSOP-8 -40 to 85°C TR: Tape & Reel Blank: Tube Part Number Marking ID Packing Type AP3503EMP-G1 3503EMP-G1 Tube AP3503EMPTR-G1 3503EMP-G1 Tape & Reel BCD Semiconductor's Pb-free products, as designated with "G1" suffix in the part number, are RoHS compliant and green. May. 2012 Rev. 1. 6 BCD Semiconductor Manufacturing Limited 3 Preliminary Datasheet 340kHz, 3A Synchronous DC-DC Buck Converter AP3503E Absolute Maximum Ratings (Note 1) Parameter Symbol Value Unit IN Pin Voltage VIN -0.3 to 20 V EN Pin Voltage VEN -0.3 to VIN V SW Pin Voltage VSW 21 V BS Pin Voltage VBS -0.3 to VSW+6 V FB Pin Voltage VFB -0.3 to 6 V VCOMP -0.3 to 6 V SS Pin Voltage VSS -0.3 to 6 V Thermal Resistance θJA 60 ºC/W Operating Junction Temperature TJ 150 ºC Storage Temperature TSTG -65 to 150 ºC Lead Temperature (Soldering, 10sec) TLEAD 260 ºC ESD (Human Body Model) VHBM 2000 V ESD (Machine Model) VMM 200 V COMP Pin Voltage Note 1: Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “Recommended Operating Conditions” is not implied. Exposure to “Absolute Maximum Ratings” for extended periods may affect device reliability. Recommended Operating Conditions Parameter Symbol Min Max Unit Input Voltage VIN 4.5 18 V Operating Ambient Temperature TA -40 85 ºC May. 2012 Rev. 1. 6 BCD Semiconductor Manufacturing Limited 4 Preliminary Datasheet 340kHz, 3A Synchronous DC-DC Buck Converter AP3503E Electrical Characteristics TA=25ºC, VIN=VEN=12V, VOUT=3.3V, unless otherwise specified. Parameter Symbol Conditions Min Typ Max Unit 1.2 0.1 18 1.4 10 V mA µA SUPPLY VOLTAGE (IN PIN) Input Voltage Quiescent Current Shutdown Supply Current VIN IQ ISHDN 4.5 VFB=1V, VEN=3V VEN=0V UNDER VOLTAGE LOCKOUT Input UVLO Threshold Input UVLO Hysteresis VUVLO VHYS VIN Rising 3.65 4.00 200 4.25 V mV 1.1 1.5 2 V ENABLE (EN PIN) EN Shutdown Threshold Voltage EN1Shutdown1Threshold1Voltage1Hysteresis (Note 3) 350 EN Lockout Threshold Voltage EN Lockout Hysteresis mV 2.2 2.5 210 2.7 V mV 0.907 0.925 1.1 0.943 V V µA VOLTAGE REFERENCE (FB PIN) Feedback Voltage Feedback Over Voltage Threshold Feedback Bias Current VFB VFBOV IFB VFB=1V RDSONH RDSONL ISW=0.2A/0.7A ISW=-0.2A/-0.7A ILEAKH ILIMH ILIML VIN=18V, VEN=VSW=0V -0.1 0.1 MOSFET High-side Switch On-resistance(Note 2) Low-side Switch On-resistance(Note 2) 100 100 mΩ mΩ CURRENT LIMIT High-side Switch Leakage Current High-side Switch Current Limit Low-side Switch Current Limit 4.3 Drain to Source 0.1 5.6 0 10 µA A mA 340 90 90 400 kHz kHz % % SWITCHING REGULATOR Oscillator Frequency Short Circuit Oscillator Frequency Max. Duty Cycle Min. Duty Cycle fOSC1 fOSC2 DMAX DMIN 280 VFB=0.85V VFB=1V 0 ERROR AMPLIFIER Error Amplifier Voltage Gain (Note 3) Error Amplifier Transconductance COMP to Current Sense Transconductance AEA GEA GCS 400 800 5.2 V/V µA/V A/V TOTSD THYS 160 20 ºC ºC 15 5 ms µA THERMAL SHUTDOWN Thermal Shutdown (Note 3) Thermal Shutdown Hysteresis (Note 3) SOFT START (SS PIN) Soft-start Time (Note 3) Soft-start Current Note 2: RDSON= tSS C4=0.1µF,IOUT=500mA VSW1 - VSW2 ISW1 - ISW2 Note 3: Not tested, guaranteed by design. May. 2012 Rev. 1. 6 BCD Semiconductor Manufacturing Limited 5 Preliminary Datasheet 340kHz, 3A Synchronous DC-DC Buck Converter AP3503E Typical Performance Characteristics TA=25ºC, VIN=12V, VOUT=3.3V, unless otherwise noted. 1.30 100 1.25 90 1.20 Quiescent Current (mA) 80 Efficiency (%) 70 60 50 40 o VOUT=3.3V,L=10µH,TA=25 C 30 1.10 1.05 1.00 0.95 0.90 VIN=5V VIN=12V 20 1.15 0.85 0.80 10 0.01 0.1 1 -50 -25 0 25 75 100 125 150 o Figure 4. Efficiency vs. Load Current Figure 5. Quiescent Current vs. Temperature 1.2 3.6 1.1 3.5 1.0 3.4 Output Voltage (V) Feedback Voltage (V) 50 Temperature ( C) Load Current (A) 0.9 0.8 3.3 3.2 3.1 0.7 3.0 0.6 -50 -25 0 25 50 75 100 125 0.0 150 Temperature ( C) 0.8 1.2 1.6 2.0 2.4 2.8 3.2 Figure 7. Output Voltage vs. Load Current Figure 6. Feedback Voltage vs. Temperature May. 2012 0.4 Load Current (A) o Rev. 1. 6 BCD Semiconductor Manufacturing Limited 6 Preliminary Datasheet 340kHz, 3A Synchronous DC-DC Buck Converter AP3503E Typical Performance Characteristics (Continued) TA=25ºC, VIN=12V, VOUT=3.3V, unless otherwise noted. 3.6 6 3.5 Maximum Load Current (A) Output Voltage (V) 5 3.4 3.3 3.2 IOUT=1.5A 3.1 4 3 2 VOUT=3.3V L=10µH 1 3.0 4 8 12 16 4 20 Figure 8. Output Voltage vs. Input Voltage VIN(AC) 200mV/div 8 12 16 20 Input Voltage (V) Input Voltage (V) Figure 9. Maximum Load Current vs. Input Voltage VOUT (AC) 100mV/div VOUT (AC) 10mV/div IL 1A/div IOUT 1A/div VSW 10V/div Time 2µs/div Time 200µs/div Figure 10. Output Ripple (IOUT=3A) May. 2012 Figure 11. Load Transient (IOUT=1.5 to 3A) Rev. 1. 6 BCD Semiconductor Manufacturing Limited 7 Preliminary Datasheet 340kHz, 3A Synchronous DC-DC Buck Converter AP3503E Typical Performance Characteristics (Continued) TA=25ºC, VIN=12V, VOUT=3.3V, unless otherwise noted. VEN 2V/div VEN 2V/div VSS 2V/div VSS 2V/div VOUT 2V/div IL 2A/div VOUT 2V/div IL 2A/div Time 10ms/div Time 200µs/div Figure 12. Enable Turn-on Characteristic (VIN=12V, VEN=3.3V, VOUT=3.3V, IOUT=3A) VOUT 2V/div Figure 13. Enable Turn-off Characteristic (VIN=12V, VEN=3.3V, VOUT=3.3V, IOUT=3A) VOUT 2V/div VSW 10V/div VSS 1V/div IL 2A/div VSW 10V/div VSS 1V/div IL 2A/div Time 100ms/div Time 100ms/div Figure 14. Short Circuit Protection (IOUT=3A) May. 2012 Figure 15. Short Circuit Recovery (IOUT=3A) Rev. 1. 6 BCD Semiconductor Manufacturing Limited 8 Preliminary Datasheet 340kHz, 3A Synchronous DC-DC Buck Converter AP3503E Typical Application Input Voltage=12V 1 2 Output Voltage=3.3V L 10µH C4 10nF 3 4 C22 C21 22µF/25V 22µF/25V BS IN SW GND AP3503E R4 100k SS EN COMP FB C12 10µF/25V 8 C5 0.1µF 7 C6 Optional 6 C3 3.3nF 5 R2 D1 Optional C11 10µF/25V R3 13k 10k R1 26.1k Figure 16. Typical Application of AP3503E May. 2012 Rev. 1. 6 BCD Semiconductor Manufacturing Limited 9 Preliminary Datasheet 340kHz, 3A Synchronous DC-DC Buck Converter AP3503E Mechanical Dimensions Unit: mm(inch) 3.202(0.126) 3.402(0.134) PSOP-8 May. 2012 Rev. 1. 6 BCD Semiconductor Manufacturing Limited 10 BCD Semiconductor Manufacturing Limited http://www.bcdsemi.com IMPORTANT NOTICE IMPORTANT NOTICE BCD Semiconductor BCD Semiconductor Manufacturing Manufacturing Limited Limited reserves reserves the the right right to to make make changes changes without without further further notice notice to to any any products products or or specifispecifications herein. cations herein. BCD BCD Semiconductor Semiconductor Manufacturing Manufacturing Limited Limited does does not not assume assume any any responsibility responsibility for for use use of of any any its its products products for for any any particular purpose, particular purpose, nor nor does does BCD BCD Semiconductor Semiconductor Manufacturing Manufacturing Limited Limited assume assume any any liability liability arising arising out out of of the the application application or or use use of any of any its its products products or or circuits. circuits. BCD BCD Semiconductor Semiconductor Manufacturing Manufacturing Limited Limited does does not not convey convey any any license license under under its its patent patent rights rights or or other rights other rights nor nor the the rights rights of of others. others. MAIN SITE SITE MAIN - Headquarters BCD Semiconductor Manufacturing Limited BCD Semiconductor Manufacturing Limited - Wafer Fab No. 1600, Zi Xing Road, Shanghai ZiZhu Science-basedLimited Industrial Park, 200241, China Shanghai SIM-BCD Semiconductor Manufacturing Tel: Fax: +86-21-24162277 800,+86-21-24162266, Yi Shan Road, Shanghai 200233, China Tel: +86-21-6485 1491, Fax: +86-21-5450 0008 REGIONAL SALES OFFICE Shenzhen OfficeSALES OFFICE REGIONAL - Wafer FabSemiconductor Manufacturing Limited BCD Shanghai SIM-BCD Semiconductor Manufacturing Co., Ltd. - IC Design Group 800 Yi Shan Road, Shanghai 200233, China Corporation Advanced Analog Circuits (Shanghai) Tel: +86-21-6485 1491,YiFax: 0008200233, China 8F, Zone B, 900, Shan+86-21-5450 Road, Shanghai Tel: +86-21-6495 9539, Fax: +86-21-6485 9673 Taiwan Office Shanghai Semiconductor Manufacturing Co., Ltd., Shenzhen Office BCD Taiwan Semiconductor Shenzhen SIM-BCD Office Office (Taiwan) Company Limited Unit A Room 1203, Skyworth Bldg., Gaoxin Ave.1.S., Nanshan Shenzhen, 4F, 298-1, Guang Road,(Taiwan) Nei-Hu District, Taipei, Shanghai SIM-BCD Semiconductor Manufacturing Co., Ltd.District, Shenzhen Office BCDRui Semiconductor Company Limited China Taiwan Advanced Analog Circuits (Shanghai) Corporation Shenzhen Office 4F, 298-1, Rui Guang Road, Nei-Hu District, Taipei, Tel: +86-755-8826 Tel: +886-2-2656 2808 Room E, 5F, Noble 7951 Center, No.1006, 3rd Fuzhong Road, Futian District, Shenzhen 518026, China Taiwan Fax: +86-755-88267951 7865 Fax: +886-2-2656 28062808 Tel: +86-755-8826 Tel: +886-2-2656 Fax: +86-755-8826 7865 Fax: +886-2-2656 2806 USA Office BCD Office Semiconductor Corp. USA 30920Semiconductor Huntwood Ave.Corporation Hayward, BCD CA 94544, USA Ave. Hayward, 30920 Huntwood Tel :94544, +1-510-324-2988 CA U.S.A Fax:: +1-510-324-2988 +1-510-324-2788 Tel Fax: +1-510-324-2788